Manufacturing Engineering & Technology
7th Edition
ISBN: 9780133559897
Author: KALPAKJIAN
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Videos
Question
Chapter 32, Problem 43SDP
To determine
Give examples of products in which rivets in a structure or in an assembly may have to be removed and later replaced by new rivets.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
What do you understand by the term welded joint? How it differs from riveted joint?
Explain with neat sketch, the joining process of “Riveting”.
Give a detailed explanation.
Explain why fasteners, such as bolt-and-nut, used in machines operating at high temperature must be re-tightened regularly.
Chapter 32 Solutions
Manufacturing Engineering & Technology
Ch. 32 - What is the difference between brazing and...Ch. 32 - Are fluxes necessary in brazing? If so, why?Ch. 32 - Why is surface preparation important in...Ch. 32 - What materials are typically used in solder?Ch. 32 - Soldering is generally applied to thinner...Ch. 32 - Explain the reasons why a variety of mechanical...Ch. 32 - List three brazing and three soldering techniques.Ch. 32 - Describe the similarities and differences between...Ch. 32 - What precautions should be taken in the...Ch. 32 - What difficulties are involved in joining...
Ch. 32 - Prob. 11RQCh. 32 - What are the principles of (a) wave soldering...Ch. 32 - What is a peel test? Why is it useful?Ch. 32 - What is a combination joint?Ch. 32 - Prob. 15RQCh. 32 - Prob. 16QLPCh. 32 - Prob. 17QLPCh. 32 - Comment on your observations concerning the...Ch. 32 - Give examples of combination joints other than...Ch. 32 - Discuss the need for fixtures for holding...Ch. 32 - Explain why adhesively bonded joints tend to be...Ch. 32 - It is common practice to tin-plate electrical...Ch. 32 - Give three applications where adhesive-bonding is...Ch. 32 - Prob. 24QLPCh. 32 - If you are designing a joint that must be strong...Ch. 32 - Prob. 26QLPCh. 32 - Rate lap, butt, and scarf joints in terms of...Ch. 32 - Prob. 28QLPCh. 32 - Prob. 29QTPCh. 32 - Prob. 30QTPCh. 32 - Prob. 31QTPCh. 32 - Figure 32.4 shows qualitatively the tensile and...Ch. 32 - When manufacturing the fuselage of a commuter...Ch. 32 - Prob. 34SDPCh. 32 - Name several products that have been assembled...Ch. 32 - Suggest methods of attaching a round bar (made of...Ch. 32 - Prob. 38SDPCh. 32 - Prob. 39SDPCh. 32 - Prob. 40SDPCh. 32 - Prob. 41SDPCh. 32 - Describe part shapes that cannot be joined by...Ch. 32 - Prob. 43SDPCh. 32 - Prob. 44SDPCh. 32 - Prob. 45SDPCh. 32 - Prob. 46SDPCh. 32 - Review Fig. 32.9a and explain the shortcoming...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Write down the damage patterns that occur in the rivet joints that are forced axially. Explain how strength calculations are made under static stresses.arrow_forwardEnumerate the different types of riveted joints and rivets.arrow_forwardA strip with cross section 120 X 6 mm is being rolled with 20 % reduction area, using rolls of 400mm diameter the coefficient of friction is 0.1 Determine the final strip thickness the angle of bite, length of deformation zonearrow_forward
- 19. Describe and explain, with the aid of diagrams, the phenomenon of die swell and how it may be reduced or compensated for in polymer extrusion techniques.20. Describe (with the aid of any diagrams as appropriate) two types of defect that may be encountered in a welded metal joint 21. With reference to optimising the use of weld metal, outline (with the aid of any diagrams as appropriate) two considerations given to welded joint design. 22. Outline the use of liquid (dye/fluorescent) penetrants as a non-destructive testing method. 23. Outline (with the aid of any diagrams if needed) four limitations of adhesive bonding. 24. Threaded components (i.e. screws, nuts, bolts) and rivets are commonly used mechanical fasteners. Describe, with the aid of diagrams, two other methods of mechanical fastening that are also used in manufacturing. answer all partsarrow_forwardIf the ratio of the diameter of rivet hole to the pitch of rivets is 0.25, then the tearing efficiency of the joint isarrow_forwardForging procedures may be characterised in part by the degree to which the amount of work that can be done is restricted in the die. Give me the names of the three primary categories that result from this grouping.arrow_forward
- If you were hired to design this bar, what would your suggested load be. Please explain in just simple sentences with concepts/justification.arrow_forwardA solid cylindrical work piece is reduced in height by an open die forging process using flat dies on a mechanical press, powered by a 20 kW motor which operates at 35 strokes per minute with a stroke length of 160 mm. The work piece is 60 mm high and 100 mm in diameter and is to be reduced in height by 15%. The coefficient of friction during the operation is 0,18. Calculate the flow stress of work piece material if the press is set to operate at 90% of its maximum capacity.arrow_forwardWhat is the difference between plate and sheet material?arrow_forward
arrow_back_ios
arrow_forward_ios
Recommended textbooks for you
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Differences between Temporary Joining and Permanent Joining.; Author: Academic Gain Tutorials;https://www.youtube.com/watch?v=PTr8QZhgXyg;License: Standard Youtube License