Manufacturing Engineering & Technology
7th Edition
ISBN: 9780133559897
Author: KALPAKJIAN
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Question
Chapter 32, Problem 41SDP
To determine
Comment on workpiece size and shape limitations, if any, for each of the processes described in this chapter.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Explain the importance of lubrication in wire drawing
Q#4: (b) Explain the disadvantages of Tube Drawing process in which mandrel is not used.
What is the difference between caulking and fullering? Explain with the help of neat sketches.
Chapter 32 Solutions
Manufacturing Engineering & Technology
Ch. 32 - What is the difference between brazing and...Ch. 32 - Are fluxes necessary in brazing? If so, why?Ch. 32 - Why is surface preparation important in...Ch. 32 - What materials are typically used in solder?Ch. 32 - Soldering is generally applied to thinner...Ch. 32 - Explain the reasons why a variety of mechanical...Ch. 32 - List three brazing and three soldering techniques.Ch. 32 - Describe the similarities and differences between...Ch. 32 - What precautions should be taken in the...Ch. 32 - What difficulties are involved in joining...
Ch. 32 - Prob. 11RQCh. 32 - What are the principles of (a) wave soldering...Ch. 32 - What is a peel test? Why is it useful?Ch. 32 - What is a combination joint?Ch. 32 - Prob. 15RQCh. 32 - Prob. 16QLPCh. 32 - Prob. 17QLPCh. 32 - Comment on your observations concerning the...Ch. 32 - Give examples of combination joints other than...Ch. 32 - Discuss the need for fixtures for holding...Ch. 32 - Explain why adhesively bonded joints tend to be...Ch. 32 - It is common practice to tin-plate electrical...Ch. 32 - Give three applications where adhesive-bonding is...Ch. 32 - Prob. 24QLPCh. 32 - If you are designing a joint that must be strong...Ch. 32 - Prob. 26QLPCh. 32 - Rate lap, butt, and scarf joints in terms of...Ch. 32 - Prob. 28QLPCh. 32 - Prob. 29QTPCh. 32 - Prob. 30QTPCh. 32 - Prob. 31QTPCh. 32 - Figure 32.4 shows qualitatively the tensile and...Ch. 32 - When manufacturing the fuselage of a commuter...Ch. 32 - Prob. 34SDPCh. 32 - Name several products that have been assembled...Ch. 32 - Suggest methods of attaching a round bar (made of...Ch. 32 - Prob. 38SDPCh. 32 - Prob. 39SDPCh. 32 - Prob. 40SDPCh. 32 - Prob. 41SDPCh. 32 - Describe part shapes that cannot be joined by...Ch. 32 - Prob. 43SDPCh. 32 - Prob. 44SDPCh. 32 - Prob. 45SDPCh. 32 - Prob. 46SDPCh. 32 - Review Fig. 32.9a and explain the shortcoming...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Explain the difference between deep drawing and redrawing.arrow_forwardExplain process in which there is continuous supply of molten metal available, with a neat diagram with labelling.arrow_forwardDescribe with the aid of a neat sketches two forging processes and briefly discuss their relative merits and limitations:arrow_forward
- Explain why friction is undesirable in metal forming operations.arrow_forwardExplain what you know about crystallographic anisotropy, which has an important place in sheet metal forming operations, with the help of shapes and formulations.arrow_forwardForging procedures may be characterised in part by the degree to which the amount of work that can be done is restricted in the die. Give me the names of the three primary categories that result from this grouping.arrow_forward
- A cup of internal diameter 80 mm and height 45 mm is to be drawn from a sheet metal 2 mm thick. Four blank sizes are available for the operation. You want to ensure the blank is large enough to make the required cup height while minimizing the material waste. Calculate the starting blank diameter for this operation?arrow_forwardExplain in detail the different types of friction?arrow_forwardexplain the difference between cold rolling and hot rolling and why the surface finish is better on cold-rolled metals compared to hot-rolled metalsarrow_forward
arrow_back_ios
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Types of Manufacturing Process | Manufacturing Processes; Author: Magic Marks;https://www.youtube.com/watch?v=koULXptaBTs;License: Standard Youtube License