Manufacturing Engineering & Technology
7th Edition
ISBN: 9780133559897
Author: KALPAKJIAN
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 32, Problem 33QTP
When manufacturing the fuselage of a commuter airplane, aluminum plates are adhesively bonded together with lap joints. Because the elastic deformation for a single plate differs from the deformation for two plates in a lap joint, the maximum shear stress in the adhesive is twice as high as the average shear stress. The shear strength of the adhesive is 20 MPa, the tensile strength of the aluminum plates is 95 MPa, and their thickness is 4.0 mm. Calculate the overlapping length needed to make the adhesive joint twice as strong as the aluminum plate.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A paper clip is made of wire 1 mm in diameter. If the original material from which the wire is made is a rod 50 mm in diameter, calculate the longitudinal engineering and true strains that the wire has undergone during processing.
A polymer straight propeller with a diameter = 15in(measured diameter = 382mm) and pitch = 5.6in(142.24mm). A drawing is given below for the propeller.
Explain the diameter of the propeller, pitch of the propellerand the drawing given.
A paper clip is made of wire 0.7 mm in diameter. If the original material from which thewire is made is a rod 25 mm in diameter, calculate the longitudinal engineering and truestrains that the wire has undergone during processing.
Chapter 32 Solutions
Manufacturing Engineering & Technology
Ch. 32 - What is the difference between brazing and...Ch. 32 - Are fluxes necessary in brazing? If so, why?Ch. 32 - Why is surface preparation important in...Ch. 32 - What materials are typically used in solder?Ch. 32 - Soldering is generally applied to thinner...Ch. 32 - Explain the reasons why a variety of mechanical...Ch. 32 - List three brazing and three soldering techniques.Ch. 32 - Describe the similarities and differences between...Ch. 32 - What precautions should be taken in the...Ch. 32 - What difficulties are involved in joining...
Ch. 32 - Prob. 11RQCh. 32 - What are the principles of (a) wave soldering...Ch. 32 - What is a peel test? Why is it useful?Ch. 32 - What is a combination joint?Ch. 32 - Prob. 15RQCh. 32 - Prob. 16QLPCh. 32 - Prob. 17QLPCh. 32 - Comment on your observations concerning the...Ch. 32 - Give examples of combination joints other than...Ch. 32 - Discuss the need for fixtures for holding...Ch. 32 - Explain why adhesively bonded joints tend to be...Ch. 32 - It is common practice to tin-plate electrical...Ch. 32 - Give three applications where adhesive-bonding is...Ch. 32 - Prob. 24QLPCh. 32 - If you are designing a joint that must be strong...Ch. 32 - Prob. 26QLPCh. 32 - Rate lap, butt, and scarf joints in terms of...Ch. 32 - Prob. 28QLPCh. 32 - Prob. 29QTPCh. 32 - Prob. 30QTPCh. 32 - Prob. 31QTPCh. 32 - Figure 32.4 shows qualitatively the tensile and...Ch. 32 - When manufacturing the fuselage of a commuter...Ch. 32 - Prob. 34SDPCh. 32 - Name several products that have been assembled...Ch. 32 - Suggest methods of attaching a round bar (made of...Ch. 32 - Prob. 38SDPCh. 32 - Prob. 39SDPCh. 32 - Prob. 40SDPCh. 32 - Prob. 41SDPCh. 32 - Describe part shapes that cannot be joined by...Ch. 32 - Prob. 43SDPCh. 32 - Prob. 44SDPCh. 32 - Prob. 45SDPCh. 32 - Prob. 46SDPCh. 32 - Review Fig. 32.9a and explain the shortcoming...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The compressive strength of aramid fiber is about one-eighth of its tensile stress. Estimate the smallest diameter of a rod on which the aramid fiber can be wound without causing kinks, etc., on its compression side.arrow_forwardA direct extrusion operation produces a product with a 20 mm x 60 mm cross sectional area from a brass billet whose diameter = 125 mm and length = 350 mm. The flow curve parameters of the brass are K = 700 MPa and n = 0.35. In the Johnson strain equation, a = 0.7 and b = 1.4. Determine (a) the extrusion ratio, (b) the shape factor, (c) the force required to drive the ram forward during extrusion at the point in the process when the billet length remaining in the container = 300 mm, and (d) the length of the extruded section at the end of the operation if the volume of the butt left in the container is 600,000 mm3arrow_forwardWhen choosing a polymer for fatigue crack propagation resistance, would you typically select an amorphous thermoplastic, a semicrystalline polymer, or a heavily crosslinked material? Other than crystallinity and cross-linking, what characteristic of a polymer can have a profound effect on FCP rate?arrow_forward
- Explain why the fatigue life (Nf) of a polymer specimen should decrease with increasing frequency.arrow_forwardIn a sheet metal forming press, the shape to be formed is hemispherical cup of radius 15 cm in 2mm thick mild steel sheet. The force required to deform sheet is 8 kN. The forming hammer should approach job from a distance of 30 cm. The production rate required is 240 components/hr. Calculate and suggest the following specifications of the various hydraulic components used: a. Hydraulic cylinder (bore & length); b. Pump pressure and flow rate; c. Electric motor HP considering 75% pump efficiency; d. Reservoir size; and e. Size of pump inlet and discharge tubing.arrow_forwarda) A bicycle frame is being designed to carry a pedal force of 800N. Assuming axial loading only, which material will produce the lightest frame out of the two in the table below? Assume a design factor of 1.2 b) If the bicycle frame is being welded together and an internal flaw size of 30mm results, which material will produce the lighter section? (Apply a design factor of 1.2 If the bicycle frame needs to last a minimum 3 x 105 cycles, with an average stress of 150MPa and an alternating stress of 200MPa, use the Soderberg criterion to pick a suitable material from the two alloys listed above. Show all your working.arrow_forward
- A force of 1100 KN is applied to punch a 40-mm-diameter hole in a plate. If the shear strength is limited to 700 MPa then what thickness of the plate is required?arrow_forwardExpound on twinning as a mechanism for plastic deformation and include conditions for which it will take place.arrow_forwardExplain in your own words how the stress test (performance test) is applied to the patient turning apparatus shown in the figure, and guess how the expected result will be. The main part of the product consists of a polyurethane sponge. Stain-proof upholstery fabric will be used as the outer surface material. In addition, there are heating pads working with the logic of electric blankets in this apparatus, please answer by taking these into account when answering.arrow_forward
- A force of 1100 KN is applied to punch a 40-mm-diameter hole in a plate. If the shear strength is limited to 700MPa then what thickness of the plate is required?arrow_forwardA hole is to be punched out on a layer of papers using a puncher with a hole diameter of 100 mm. If the compressive stress in the punch is limited to 15.1 Mpa. Calculate for the maximum stacking depth (mm) of paper for a single punch considering each paper is 125 micron and a shearing strength of 13.5 Mpa. please answer it.arrow_forwardA cylindrical specimen of brass that has a diameter of 15 mm, a tensile modulus of 100 GPa, and a Poisson's ratio of 0.35 is pulled in tension with a force of 40, 000 N. If the deformation is totally elastic and the original length is 120 mm, what is the final diameter of the specimen in mm?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Basic Fabrication Techniques; Author: Weld.com;https://www.youtube.com/watch?v=3OW7iRnC8Ck;License: Standard Youtube License