AUTOMOTIVE TECHNOLOGY TECH MANUAL
7th Edition
ISBN: 9781337794220
Author: ERJAVEC
Publisher: CENGAGE L
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 39, Problem 1TF
To determine
The truth of the statement.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Technician A says that some manual transmissions use 85/90 weight gear oil or synchromesh transmission fluid.Technician B says that some manual transmissions use automatic transmission fluid.Who is correct?
While discussing valve body assemblies in late-model transmissions: Technician A says that the valve body is no longer needed in some electronically controlled transmissions. Technician B says that an EPC solenoid maintains constant fluid pressure through the valve body regardless of the vehicle’s operating condition. Who is correct?
manual transmissions are being discussed. technician a says that if it requires gear oil, to always use gl-5 rated oil to protect the synchronizers. technician b says that if it requires engine oil that you should add a friction modifier to it. who is correct?
Chapter 39 Solutions
AUTOMOTIVE TECHNOLOGY TECH MANUAL
Ch. 39 - After draining gear oil from a transaxie, the...Ch. 39 - Prob. 2SACh. 39 - Prob. 3SACh. 39 - What tool is often required to remove gears and...Ch. 39 - When removing or installing bearings, where should...Ch. 39 - List five common sources for transmission fluid...Ch. 39 - What should you do to properly identify the type...Ch. 39 - List at least five items that are typically...Ch. 39 - Prob. 1TFCh. 39 - True or False? Bearing noise increases under load...
Ch. 39 - A rough, growling noise that is heard from a...Ch. 39 - A clicking noise during transrnission/transaxle...Ch. 39 - Worn teeth on a speed gear can cause_______. a....Ch. 39 - Using a lubricant that is thicker than the...Ch. 39 - A poorly adjusted shift linkage can cause which of...Ch. 39 - Technician A says that the transmission rear seal...Ch. 39 - A noise occurs in forward and reverse gears but...Ch. 39 - A rough, growling noise occurs when a vehicle with...Ch. 39 - A car jumps out of gear into neutral, particularly...Ch. 39 - While diagnosing a noise from a transmission:...Ch. 39 - Technician A says that broken or worn engine and...Ch. 39 - Technician A says that shims may be used to adjust...Ch. 39 - During a test drive, a noise that appears to be...Ch. 39 - While inspecting the synchronizers of a transaxle:...Ch. 39 - Technician A says that the proper fluid level for...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Technician A says that all manual transmission vehicles have at least one pilot bearing or bushing for the input shaft. Technician B says that the pressure plate always rotates with the input shaft when the engine is running. ‘Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardTrue or False? The vent in a transmission housing is designed to allow fluid to escape when there is excessive pressure in the system.arrow_forwardWhen servicing transfer cases, all of the following are correct, except_____. a. it must be supported on a transmission jack or safety stands b. the chain drive and a planetary gearset must be adjusted to specifications c. visual inspections for leaks and damage are necessary d. follow the manufacturers recommendations for lubricantsarrow_forward
- While checking the engine and transmission mounts on a FWD car: Technician A says that any engine movement may change the effective length of the shift and throttle cables and therefore may affect the engagement of the gears. Technician B says that delayed or missed shifts are caused by hydraulic prob lems, not linkage or control problems. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardTechnician A says that the proper fluid level for a manual transmission is normally to the bottom of the filler hole. Technician B says that low lubricant levels can cause a standard transmission to clash during shifting. Who is correct?arrow_forward128) Technician A says slide hammer pullers are usually required to remove the front pump from the transmission housing. Technician B says a special tool is available to remove the front pump on some transmissions. Which technician is correct? O Technician A Technician B O Both technicians A and B Neither technician A nor Barrow_forward
- 122) Technician A says when removing a transmission, the rear of the engine will usually need to be tilted down to allow room. Technician B says moving the position of the engine could pull electrical harnesses or coolant hoses loose. Which technician is correct? O Technician A O Technician B Both technicians A and B O Neither technician A nor Barrow_forwardTechnician A says that an in-line six-cylinder diesel engine is usually longer and heavier than a V8 engine of the same displacement. Technician B says that there are twice as many teeth on the crankshaft as there are on the camshaft sprocket. Who is correct? and why? Technician A Technician B Both A and B Neither A nor Barrow_forwardTrue or False? Make sure you locate and adhere to the wet torque specs when tightening a bolt that has been lubricated with oil or any other liquid.arrow_forward
- Which type of transmission uses pulleys to change engine speed? Dual-dutch Manual Continuously varaible Automaticarrow_forwardTechnician A says that changes in engine load cause changes in hydraulic pressure inside the transmission. Technician B says that engine load is monitored by throttle pedal movement or by engine vacuum. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardWhy do we need to diagnose the transmission/transaxle failure?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Understanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Understanding Motor Controls
Mechanical Engineering
ISBN:9781337798686
Author:Stephen L. Herman
Publisher:Delmar Cengage Learning