Consider a 7.6-cm-long and 3-cm-diameter cylindrical Iamb meat chunk
(a) 71 kJ
(b) 227kJ
(c) 238 kJ
(d) 269k)
(e) 307 kJ
Want to see the full answer?
Check out a sample textbook solutionChapter 4 Solutions
Package: Loose Leaf for Heat and Mass Transfer: Funamentals & Applications with 1 Semester Connect Access Card
- A person is found dead at 5PM in a room whose temperature is 20°C. Thetemperature of the body is measured to be 25°C when found, Modeling thebody as a 30-cm-diameter, 1.70-m-long cylinder and the heat transfer coefficient estimated to be 8 W/m2·K. and using the lumped system analysis as a rough approximation, estimate the time of death of the person.arrow_forwardA long steel rod 0.305 m in diameter is initially at a temperature of 588 K. It is immersed in an oil bath maintained at 311 K. The surface convective coefficient is 125 W/m2 -K. Calculate the temperature at the center of the rod after 1 h. The average physical properties of the steel are k = 38 W/m-K and α = 0.0381 m2/h.arrow_forwardWhat is heat transfer coefficient?arrow_forward
- If we neglect radiative heat transfer, what is the appropriate heat transfer coefficient value for stagnant ambient air?arrow_forwardIn a food industry, pieces of meat with approximately 30 cm in diameter and 20 mm in thickness are stored in a industrial freezer and thawed by exposure to ambient air at 15°C with convective heat transfer coefficient equal to 10W/(m2.K). Consider a piece of meat that, when removed from the freezer, had a temperature of -12°C. For defrosting, the piece is hung on a "line", so that both larger surfaces are exposed to the ambient air. For frozen meat, the following properties can be assumed ρ=1090 kg/m3, cp=3.54 kJ/(kg.K), k=0.47 W/(m.K). Ask: (1) Indicating the control volume and the simplifications adopted, obtain the differential energy balance equation for the cooling the piece of meat and describe the conditions of outline and initial that apply to the process, justifying them; (2) Use the appropriate analytical solution to determine the time necessary for the complete defrosting of the part. The part is considered to be completely thawed when a minimum temperature of 5oC is reached…arrow_forward. Castor oil at 36 °C flows over a 6 m long and 1 m wide heated plate at 0.06 m/s. For a surfacetemperature of 96 °C, determine (i) the thermal boundary layer thickness at the end of the plate,(ii) the local heat transfer coefficient at the end of the plate, and (iii) the rate of heat transfer fromthe entire platearrow_forward
- -Determine the Reynold's number -Determine the Nusselt number -Determine the heat transfer coefficient -Estimate the heat transfer per unit lengtharrow_forwardCombustion gases passing through a 3-cminternal- diameter circular tube are used to vaporize waste water at atmospheric pressure. Hot gases enter the tube at 115 kPa and 250°C at a mean velocity of 5 m/s, and leave at 150°C. If the average heat transfer coefficient is 120 W/m2?K and the inner surface temperature of the tube is 110°C, determine (a) the tube length and (b) the rate of evaporation of water.arrow_forwardAcertain superinsulation material having a thermal conductivity of 2*10^-4 W/m*^ C is used to insulate a tank of liquid nitrogen that is maintained at - 196 degrees * C : 199 kJ is required to vaporize each kilogram mass of nitrogen at this temperature. Assuming that the tank is a sphere having an inner diameter (ID) of 0.52 m, estimate the amount of nitrogen vaporized per day for an insulation thickness of 2.5 cm and an ambient temperature of 21 degrees * C . Assume that the outer temperature of the insulation is 21 degrees * C .arrow_forward
- A 212-mm-square, 15-mm-thick tile has the thermo-physical properties of Pyrex (ϵ = 0.83) and emerges from a curing process at an initial temperature of Ti = 145°C. The backside of the tile is insulated while the upper surface is exposed to ambient air and surroundings at 25°C. (a) Estimate the time required for the tile to cool to a final, safe-to-touch temperature of Tf = 42°C. Use an average tile surface temperature of T¯=(Ti+Tf)/2 to estimate the average free convection coefficient and the linearized radiation coefficient. How sensitive is your estimate to the assumed value for T¯? (b) Estimate the required cooling time if ambient air is blown in parallel flow over the tile with a velocity of 10 m/sarrow_forward7.43 Liquid sodium is to be heated from 500 K to 600 K by passing it at a flow rate of 5.0 kg/s through a 5-cmID tube whose surface is maintained at 620 K. What length of tube is required?arrow_forward3.10 A spherical shell satellite (3-m-OD, 1.25-cm-thick stainless steel walls) re-enters the atmosphere from outer space. If its original temperature is 38°C, the effective average temperature of the atmosphere is 1093°C, and the effective heat transfer coefficient is , estimate the temperature of the shell after reentry, assuming the time of reentry is 10 min and the interior of the shell is evacuated.arrow_forward
- Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning