Package: Loose Leaf for Heat and Mass Transfer: Funamentals & Applications with 1 Semester Connect Access Card
5th Edition
ISBN: 9781259290534
Author: CENGEL
Publisher: MCG
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 4, Problem 176P
A large chunk of tissue at 35°C with a thermal diffusivity of
(a) 5°C
(b) 30°C
(c) 25°C
(d) 20°C
(e) 10°C
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Consider a cold aluminum canned drink that is initially at a uniform temperature of 4°C. The can is 12.5 cm high and has a diameter of 6 cm. If the combined convection/radiation heat transfer coefficient between the can and the surrounding air at 25°C is 10 W/m2 · °C, determine how long it will take for the average temperature of the drink to rise to 15°C. In an effort to slow down the warming of the cold drink, a person puts the can in a perfectly fitting 1-cm-thick cylindrical rubber insulator (k = 0.13 W/m · °C). Now how long will it take for the average temperature of the drink to rise to 15°C? Assume the top of the can is not covered.
During a picnic on a hot summer day, the only available drinks were those at the ambient temperature of 90°F. In an effort to cool a 12-fluid-oz drink in a can, which is 5 in high and has a diameter of 2.5 in, a person grabs the can and starts shaking it in the iced water of the chest at 32°F. The temperature of the drink can be assumed to be uniform at all times, and the heat transfer coefficient between the iced water and the aluminum can is 30 Btu/h·ft2·°F. Using the properties of water for the drink, estimate how long it will take for the canned drink to cool to 40°F.
An average man has a body surface area of 1.8 m2
and a skin temperature
of 330C. The convective heat transfer coefficient for a clothed person
walking in still air is expressed as
h= 8.6V0.53 where V is the walking velocity in m/s. Assuming the average
surface temperature of the clothed person to be 300C, determine the rate
of heat lost by convection from an average man walking in still air at 100C at
a walking velocity of 1.2 m/s.
Chapter 4 Solutions
Package: Loose Leaf for Heat and Mass Transfer: Funamentals & Applications with 1 Semester Connect Access Card
Ch. 4 - What is the physical significance of the Biot...Ch. 4 - What is lumped system analysis? When is it...Ch. 4 - In what medium is the lumped system analysis more...Ch. 4 - For which solid is the lumped system analysis more...Ch. 4 - For which kinds of bodies made of the same...Ch. 4 - Consider heat transfer between two identical hot...Ch. 4 - Consider heat transfer between two identical hot...Ch. 4 - Consider a hot baked potato on a plate. The...Ch. 4 - Consider a potato being baked in an oven that is...Ch. 4 - Consider two identical 4-kg pieces of roast beef....
Ch. 4 - Consider a sphere and a cylinder of equal volume...Ch. 4 - Obtain relations for the characteristic lengths of...Ch. 4 - Obtain a relation for the time required for a...Ch. 4 - A brick of 20310257mm in dimension is being burned...Ch. 4 - Prob. 15PCh. 4 - Prob. 16PCh. 4 - Metal plates...Ch. 4 - Prob. 18PCh. 4 - Prob. 19PCh. 4 - A 6-mm-thick stainless steel strip...Ch. 4 - After heat treatment, the 2-cm-thick metal plates...Ch. 4 - A long copper rod of diameter 2.0 cm is initially...Ch. 4 - Prob. 23PCh. 4 - Steel rods...Ch. 4 - To warm up some milk for a baby, a mother pours...Ch. 4 - A person is found dead at 5 p.m. in a room whose...Ch. 4 - Prob. 27PCh. 4 - In an experiment, the temperature of a hot gas...Ch. 4 - Prob. 29PCh. 4 - Pulverized coal particles are used in oxy-fuel...Ch. 4 - Oxy-fuel combustion power plants use pulverized...Ch. 4 - Plasma spraying is a process used for coating a...Ch. 4 - Consider a spherical shell satellite with outer...Ch. 4 - Prob. 34PCh. 4 - Prob. 35PCh. 4 - Prob. 36EPCh. 4 - Consider a sphere of diameter 5 cm, a cube of side...Ch. 4 - Prob. 38PCh. 4 - An egg is to be cooked to a certain level of...Ch. 4 - What is an infinitely long cylinder? When is it...Ch. 4 - What is the physical significance of the Fourier...Ch. 4 - Prob. 42CPCh. 4 - Prob. 43CPCh. 4 - Prob. 44CPCh. 4 - The Biot number during a heat transfer process...Ch. 4 - A body at an initial temperature of Ti, is brought...Ch. 4 - Prob. 47PCh. 4 - In a meat processing plant, 2-cm-thick steaks...Ch. 4 - Prob. 49PCh. 4 - Prob. 50PCh. 4 - Prob. 51PCh. 4 - Layers of 23-cm-thick meat slabs...Ch. 4 - Prob. 53PCh. 4 - Prob. 54PCh. 4 - Prob. 55EPCh. 4 - Prob. 56PCh. 4 - Prob. 57EPCh. 4 - Prob. 58PCh. 4 - A 30-cm-diameter, 4-m-high cylindrical column of a...Ch. 4 - Prob. 60PCh. 4 - Prob. 61PCh. 4 - Prob. 62PCh. 4 - Prob. 63PCh. 4 - Prob. 64PCh. 4 - Prob. 65PCh. 4 - Prob. 66PCh. 4 - Prob. 67PCh. 4 - Prob. 68PCh. 4 - Prob. 69PCh. 4 - For heat transfer purposes, an egg can be...Ch. 4 - Citrus fruits are very susceptible to cold...Ch. 4 - Prob. 72PCh. 4 - Prob. 73PCh. 4 - A 9-cm-diameter potato...Ch. 4 - Chickens with an average mass of 1.7 kg...Ch. 4 - Prob. 76PCh. 4 - In Betty Crocker s Cookbook, it is stated that it...Ch. 4 - Prob. 78PCh. 4 - Prob. 79PCh. 4 - Oranges of 2.5-in-diameter...Ch. 4 - Prob. 81EPCh. 4 - Under what conditions can a plane wall be treated...Ch. 4 - What is a semi-infinite medium? Give examples of...Ch. 4 - Consider a hot semi-infinite solid at an initial...Ch. 4 - Prob. 85EPCh. 4 - Prob. 86PCh. 4 - In areas where the air temperature remains below...Ch. 4 - Prob. 88PCh. 4 - A highway made of asphalt is initially at a...Ch. 4 - A thick aluminum block initially at 20C is...Ch. 4 - Prob. 91PCh. 4 - A thick wall made of refractory bricks...Ch. 4 - Prob. 93PCh. 4 - Prob. 94PCh. 4 - A thick wood slab (k=0.17W/m.K,=1.2810-7m2/s) and...Ch. 4 - Prob. 96PCh. 4 - Prob. 97PCh. 4 - Prob. 98PCh. 4 - Prob. 99PCh. 4 - Prob. 100PCh. 4 - Prob. 101PCh. 4 - A barefooted person whose feet are at 32C steps on...Ch. 4 - What is the product solution method? How is it...Ch. 4 - How is the product solution used to determine the...Ch. 4 - Prob. 105CPCh. 4 - Consider a short cylinder whose top and bottom...Ch. 4 - Prob. 107PCh. 4 - Prob. 108PCh. 4 - A hot dog can be considered to be a cylinder 5 in...Ch. 4 - Prob. 110PCh. 4 - Prob. 111PCh. 4 - A 2-cm-high cylindrical ice block...Ch. 4 - Prob. 113PCh. 4 - Prob. 114PCh. 4 - Prob. 115PCh. 4 - Prob. 116PCh. 4 - Prob. 117PCh. 4 - Prob. 118PCh. 4 - Prob. 119CPCh. 4 - How does refrigeration prevent or delay the...Ch. 4 - What are the environmental factors that affect the...Ch. 4 - What is the effect of cooking on the...Ch. 4 - Prob. 123CPCh. 4 - Prob. 124CPCh. 4 - Prob. 125CPCh. 4 - Prob. 126CPCh. 4 - How does the rate of freezing affect the...Ch. 4 - Prob. 128CPCh. 4 - Prob. 129CPCh. 4 - Prob. 130CPCh. 4 - Prob. 131CPCh. 4 - Prob. 132CPCh. 4 - Prob. 133PCh. 4 - Prob. 134PCh. 4 - Chickens with an average mass of 2.2 kg and...Ch. 4 - Prob. 136EPCh. 4 - Prob. 137PCh. 4 - Prob. 138PCh. 4 - A long roll of 2-m-wide and 0.5-cm-thick 1-Mn...Ch. 4 - Prob. 140PCh. 4 - Prob. 141PCh. 4 - Prob. 142PCh. 4 - During a picnic on a hot summer day, the only...Ch. 4 - Two metal rods are being heated in an oven with...Ch. 4 - Stainless steel ball bearings...Ch. 4 - Prob. 146PCh. 4 - Prob. 147PCh. 4 - In Betty crockers Cookbook, it is stated that it...Ch. 4 - A watermelon initially at 35C is to be cooled by...Ch. 4 - Prob. 150PCh. 4 - Prob. 151PCh. 4 - Prob. 152PCh. 4 - Prob. 153PCh. 4 - Prob. 154PCh. 4 - Prob. 155PCh. 4 - Prob. 156PCh. 4 - Prob. 157PCh. 4 - Prob. 158PCh. 4 - Prob. 159PCh. 4 - Lumped system analysis of transient heat...Ch. 4 - Prob. 161PCh. 4 - Prob. 162PCh. 4 - An 18-cm-long, 16-cm-wide, and 12-cm-high hot iron...Ch. 4 - Prob. 164PCh. 4 - Prob. 165PCh. 4 - Prob. 166PCh. 4 - Prob. 167PCh. 4 - Prob. 168PCh. 4 - A long 18-cm-diameter bar made of hardwood...Ch. 4 - Consider a 7.6-cm-long and 3-cm-diameter...Ch. 4 - Consider a 7.6-cm-diameter cylindrical lamb meat...Ch. 4 - Prob. 172PCh. 4 - A small chicken (k=0.45W/m.K,=0.1510-6m2/s) and...Ch. 4 - A potato may be approximated as a 5.7-cm-diameter...Ch. 4 - When water, as in a pond or lake, is heated by...Ch. 4 - A large chunk of tissue at 35C with a thermal...Ch. 4 - Prob. 177PCh. 4 - Citrus trees are very susceptible to cold weather,...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A long 10-cm-diameter steam pipe whose external surface temperature is 110°C passes through some open area that is not protected against the winds . Determine the rate of heat loss from the pipe per unit of its length when the air is at 1 atm pressure and 10°C and the wind is blowing across the pipe at a velocity of 8 m/s.arrow_forwardA cylindrical fuel rod of 2 cm in diameter is encased in a concentric tube and cooled by water. The fuel generates heat uniformly at a rate of 150 MW/m3. The convection heat transfer coefficient on the fuel rod is 5000 W/m2∙K, and the average temperature of the cooling water, sufficiently far from the fuel rod, is 70°C. Determine the surface temperature of the fuel rod and discuss whether the value of the given convection heat transfer coefficient on the fuel rod is reasonable.arrow_forwardDuring a visit to a plastic sheeting plant, it was observed that a 60-m-long section of a 2-in nominal (6.03-cm-outer-diameter) steam pipe was extended from one end of the plant to the other with no insulation on it. The temperature measurements at several locations revealed that the average temperature of the exposed surfaces of the steam pipe was 170°C, while the temperature of the surrounding air was 20°C. The outer surface of the pipe appeared to be oxidized, and its emissivity can be taken to be 0.7. Taking the temperature of the surrounding surfaces to be 20°C also, determine the rate of heat loss from the steam pipe. Steam is generated in a gas furnace that has an efficiency of 78 percent, and the plant pays $1.10 per therm (1 therm = 105,500 kJ) of natural gas. The plant operates 24 h a day 365 days a year, and thus 8760 h a year. Determine the annual cost of the heat losses from the steam pipe for this facility.arrow_forward
- A person is found dead at 5PM in a room whose temperature is 20°C. Thetemperature of the body is measured to be 25°C when found, Modeling thebody as a 30-cm-diameter, 1.70-m-long cylinder and the heat transfer coefficient estimated to be 8 W/m2·K. and using the lumped system analysis as a rough approximation, estimate the time of death of the person.arrow_forwardConsider water (at a temperature of 276 K ) flowing inside a cylindrical pipe, having a diameter of 0.1 m and a thin wall. Under specific circumstances, temperature at the wall of the pipe reaches 258 K that helps form a layer of ice on the inner side of the wall of the pipe. Temperature and convection heat transfer coefficient at the inner surface of the ice layer are 273 K and 1500m2⋅Kw, respectively. Determine how thick the ice layer should be?arrow_forwardIn a production facility, 3-cm-thick large brass plates (k =110 W/m·K, ρ= 8530kg/m3, Cp = 380 J/kg·K, and α= 33.9 x10-6 m2/s) that are initially at a uniform temperature of 25°C are heated by passing them through an oven maintained at 700°C. The plates remain in the oven for a period of 10 min. Taking the convection heat transfer coefficient to be h = 80 W/m2·K, determine the surface temperature ofthe plates when they come out of the oven. Solve this problem using analytical oneterm approximation method (not the Heisler charts). Can this problem be solved using lumped system analysis? Justify your answer. Answer: 445 ℃arrow_forward
- When is the heat transfer through a fluid conduction and when is it convection? For which case is the rate of heat transfer higher? How does the convection heat transfer differ from the thermal conductivity of the fluid?arrow_forwardWater is to be heated from 10°C to 80°C as it flows through a 2-cm-internal-diameter, 13-m-long tube. The tube is equipped with an electric resistance heater, which provides uniform heating throughout the surface of the tube. The outer surface of the heater is well insulated, so that in steady operation all the heat generated in the heater is transferred to the water in the tube. If the system is to provide hot water at a rate of 5 L/min, determine the power rating of the resistance heater. Also, estimate the inner surface temperature of the pipe at the exit.arrow_forwardA person puts a few apples into the freezer at 15°C cool them quickly for guestswho are about to arrive. Initially, the apples are at a uniform temperature of 20°C,and the heat transfer coefficient on the surfaces is 8 W/m2·K. Treating the apples as9-cm-diameter spheres and taking their properties to be 840 kg/m3, Cp 3.81 kJ/kg·K, k = 0.418 W/m·K, and α =10-7 m2/s, determine the center and surface temperatures of the apples in 1 h. Also, determine the amount of heat transfer from each apple. Solve this problem using analytical one-term approximation method (notthe Heisler charts). Answer: Center: 11.2 ℃, Surface: 2.7 ℃, heat transfer: 17.2 kJarrow_forward
- Partially-frozen ice cream is being placed in a package before completion of the freezing process. The package has dimensions of 8 cm by 10 cm by 20 cm and is placed in air- blast freezing with convective heat coefficient of 50 W/(m2 K) for freezing. The product temperature is -5°C when placed in the package, and the air temperature is -25°C. The product density is 700 kg/m3, the thermal conductivity (frozen) is 1.2 W/(m K), and the specific heat of the frozen product is 1.9 kJ/(kg K). If the latent heat to be removed during blast freezing is 100 kJ/kg, estimate the freezing time.arrow_forwardA long 8-cm-diameter steam pipe whose external surface temperature is 90°C passes through some open area that is not protected against the winds. Determine the rate of heat loss from the pipe per unit of its length when the air is at 1 atm pressure and 7°C and the wind is blowing across the pipe at a velocity of 50 km/h.arrow_forwardConsider a 1.2-m-high and 2-m-wide glass windowwith a thickness of 6 mm, thermal conductivity k = 0.78W/m·K, and emissivity « = 0.9. The room and the wallsthat face the window are maintained at 25°C, and the averagetemperature of the inner surface of the window is measuredto be 5°C. If the temperature of the outdoors is 25°C,determine (a) the convection heat transfer coefficient on theinner surface of the window, (b) the rate of total heat transferthrough the window, and (c) the combined natural convectionand radiation heat transfer coefficient on the outer surface ofthe window. Is it reasonable to neglect the thermal resistanceof the glass in this case?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Heat Transfer – Conduction, Convection and Radiation; Author: NG Science;https://www.youtube.com/watch?v=Me60Ti0E_rY;License: Standard youtube license