PROGRAMMABLE LOGIC CONTROLLERS-ACCESS
5th Edition
ISBN: 9781259680915
Author: Petruzella
Publisher: MCG
expand_more
expand_more
format_list_bulleted
Question
Chapter 4, Problem 5P
Program Plan Intro
Logic gate:
- Logic gate is an electronic circuit that is used to perform logic decisions based on the input.
- It contains one or more number of inputs and one output.
- The working of logic gate is based on the binary principle that has two states either logic 0 or logic 1.
- The output of logic gate is produced when it satisfies any of its logic conditions.
- The logic condition depends upon the type of the gates and the number of inputs.
- The primary logic gates include AND, OR, and NOT and the combinations of these gates are used to implement any of the other logic gates.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Designs a logic circuit that will allow a signal to pass to the output only when control inputs B and C are both HIGH; otherwise, the output will stay LOW
Write a Ladder Logic PLC program for each of the following scenarios. Label all contacts and coils in the PLC program.
Scenario 1
Turn on a light when either one of two switches (I1, I2) is toggled on (construct an OR Gate). Turn on a second light when both switches (Same inputs I1, I2) are toggled on (construct an AND Gate). Turn on a third light when both switches (Same inputs I1, I2) are toggled off (construct a NOR Gate). Turn on a fourth light when either switch (Same inputs I1, I2) is toggled off (construct a NAND Gate). Print a copy of the program showing the construction of the four gate configurations. Also, submit a truth table for the four input configurations.
Then modify your program so, only one light turns on at a time as you toggle the four truth table states.
Scenario 2
Construct a seal-in circuit using a stop-and-start pushbutton and an internal coil to seal in. Turn on a light for 10 seconds when the start button is pushed then turn it off automatically or…
Draw a ladder diagram in PLC programming for manually operated standing A+B+B-A- cylinder sequence.
Chapter 4 Solutions
PROGRAMMABLE LOGIC CONTROLLERS-ACCESS
Knowledge Booster
Similar questions
- onstruct the state diagram, primitive flow table and reduced flow table for a fundamental mode circuit whose behaviour is as follows: Initial condition: Both the inputs and outputs are zero For x1 = 1 and x2 = 0; output (z) = 1 x1 = 0 and x2 = 1; output (z) = 0 x1x2 = 00 and x1x2 = 11; z = previous outpuarrow_forwardCreate a PLC ladder logic diagram for an alarm that turns on when either A counts up to 10, or B counts down to 7.arrow_forwardDraw a ladder logic diagram for the timer scenario shown.arrow_forward
- Use the following state diagram and create the state table for a synchronous to detect the sequence. The circuit has a single input, x, and a single output z. The output is logic-1 whenever the input sequence 101 is detected, logic-0 otherwise. Note that overlapping sequences are allowed, Create the initial state table, and the complete state table. Write the equations for all the state variables and the output z.arrow_forward1. Briefly describe the difference between the different types of counter modules used for PLCs. 2. Design a ladder logic program for a traffic light intersection. Use timers to control the duration of the green, yellow, and red lights for each direction.arrow_forwardDraw a PLC ladder logic program that will control a motor in two different directionsarrow_forward
- Below is the logic diagram of a sequential circuit.Analyze its behavior.arrow_forwardPlease show solution to answer The state diagram for a sequential circuit appears in the following figure. Find the state table for the circuitarrow_forwardDesign a logic circuit with input signal A, control input B, and outputs X and Y to operate as follows: When B = 1, output X will follow input A, and output Y will be 0. When B = 0, output X will be 0, and output Y will follow input A.arrow_forward
- Draw a ladder logic diagram for the timer scenario shown (draw out the timer delays too)arrow_forwardA sequential circuit has two JK flip-flops A and B, two inputs x and y, and oneoutput z. The flip-flop input equations and circuit output equation areJ A = B’y + Bx’ K A = B’xy’J B = A’x’ K B = (A’)’ + x’y’Z = Axy + B’xy’(a) Draw the logic diagram of the circuit.(b) Tabulate the state table.(c) Derive the state equations for A and Barrow_forwardDevelop a PLC-based ladder logic program for automatic packaging system: 1.Draw and explain ladder logic diagram to run a conveyor motor using the following conditions: a.AND Logic Function b.NOR Logic Function Analyze the following conditions: a.Upgrade the ladder diagram such that the motor runs in both clockwise and anti-clockwise direction. b.Use two light indicators to indicate the direction of motor rotation. c.Use a photosensor to detect the package on the conveyor d.Add start stop logic (Use both AND logic and OR logic, where necessary use switches to control the direction)arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Database System ConceptsComputer ScienceISBN:9780078022159Author:Abraham Silberschatz Professor, Henry F. Korth, S. SudarshanPublisher:McGraw-Hill Education
Starting Out with Python (4th Edition)Computer ScienceISBN:9780134444321Author:Tony GaddisPublisher:PEARSON
Digital Fundamentals (11th Edition)Computer ScienceISBN:9780132737968Author:Thomas L. FloydPublisher:PEARSON
C How to Program (8th Edition)Computer ScienceISBN:9780133976892Author:Paul J. Deitel, Harvey DeitelPublisher:PEARSON
Database Systems: Design, Implementation, & Manag...Computer ScienceISBN:9781337627900Author:Carlos Coronel, Steven MorrisPublisher:Cengage Learning
Programmable Logic ControllersComputer ScienceISBN:9780073373843Author:Frank D. PetruzellaPublisher:McGraw-Hill Education
Database System Concepts
Computer Science
ISBN:9780078022159
Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan
Publisher:McGraw-Hill Education
Starting Out with Python (4th Edition)
Computer Science
ISBN:9780134444321
Author:Tony Gaddis
Publisher:PEARSON
Digital Fundamentals (11th Edition)
Computer Science
ISBN:9780132737968
Author:Thomas L. Floyd
Publisher:PEARSON
C How to Program (8th Edition)
Computer Science
ISBN:9780133976892
Author:Paul J. Deitel, Harvey Deitel
Publisher:PEARSON
Database Systems: Design, Implementation, & Manag...
Computer Science
ISBN:9781337627900
Author:Carlos Coronel, Steven Morris
Publisher:Cengage Learning
Programmable Logic Controllers
Computer Science
ISBN:9780073373843
Author:Frank D. Petruzella
Publisher:McGraw-Hill Education