Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 40, Problem 10ASRQ
While reviewing the procedure for setting backlash: Technician A says that backlash is adjusted along with side-bearing preload by loosening or tightening side-bearing adjusting nuts. Technician B says that normally, to decrease the amount of backlash, a thin shim is installed on one side of the gear and a thick one on the other side. Who is correct?
a Technician A only
b. Technician B only
c. Both A and B
d. Neither A nor B
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Technician A says that side-bearing preload limits the amount the differential case is able to move laterally in the axle housing. Technician B says that adjusting backlash sets the depths of the mesh between the ring and pinion gears’ teeth. Who is correct?
Technician A says that a hunting gearset is one in which one drive pinion gear tooth contacts only certain ring gear teeth, Technician B says that a partial nonhunting gearset is one in which one pinion tooth contacts only six ring gear teeth. Who is correct?
What is ''Dynamic load analysis of spur gears"
Chapter 40 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 40 - Prob. 1RQCh. 40 - What type of axle housing resembles a banjo?Ch. 40 - What type of axle merely supports the vehicle load...Ch. 40 - What type of floating axle has one wheel bearing...Ch. 40 - How are problems normally first noticed with the...Ch. 40 - In front-wheel drivetrains, the CV joint nearer...Ch. 40 - A CV joint that is capable of in-and-out movement...Ch. 40 - The double-offset joint is typically used in...Ch. 40 - Which type of joint has a flatter design than any...Ch. 40 - Which of these is the best way to determine which...
Ch. 40 - The single Cardan/Spicer universal joint is also...Ch. 40 - The drive shaft component that provides a means of...Ch. 40 - Large cars with long drive shafts often use a...Ch. 40 - Which type of driving axle supports the weight of...Ch. 40 - Which of the following describes the double-Cardan...Ch. 40 - Technician A says that a gear tooth pattern...Ch. 40 - Technician A says that limited-slip differential...Ch. 40 - Technician A says that side-bearing preload limits...Ch. 40 - Technician A says that a hunting gearset is one in...Ch. 40 - While discussing the possible causes for a...Ch. 40 - While diagnosing the cause of a clicking noise...Ch. 40 - Prob. 7ASRQCh. 40 - Technician A says that when a car is moving...Ch. 40 - While discussing different types of ring and...Ch. 40 - While reviewing the procedure for setting...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Which of the following is the most likely cause for a shudder during the engagement of a lock-up torque converter? a. A bad converter b. Worn or damaged CV or U-joints c. A worn front planetary gearset d. Loose flexplatearrow_forwardRadial load which acts on a gear tooth is the a. considerable load. b. horizontal component of normal load. c. vertical component of normal load. d. both a & c. Clear my choicearrow_forwardwhen checking or setting the backlash it is important to have the dial indicator tip in the correct place on the ring gear. where should the tip contact the ring geararrow_forward
- While inspecting a planetary gear-type final drive, Technician A says blackened pinion shafts indicate severe overloading. Technician B says bluish gears indicate overheating. Who is correct?arrow_forwardA noise occurs in forward and reverse gears but not in neutral: Technician A says that the input shaft bearing may be bad. Technician B says that the mainshaft bearing may be bad. Who is correct? a. Technician A only b. Technician B only c. Both Aand B d. Neither A nor Barrow_forwardWhen a transmission is described as having two planetary gearsets in tandem, what does this mean?arrow_forward
- In a simple planetary gearset, when the planetary carrier is held, the gearset produces a______. a. reverse b. direct drive c. fast overdrive d. forward reductionarrow_forwardTech A says that if a noise is caused by a set of worn gears, it will normally be loudest in that gear while driving under a load. Tech B says that if the bearings on the input shaft, countershaft, or main shaft are worn, either front or rear, a growling noise will result when stopped in gear. Who is correct?arrow_forwardA 1.5 kW motor is running at 1440 rev/min. It is to be connected to a stirrer running at 36 rev/min. The gearing arrangement suitable for this application is, (a) differential gear (b) helical gear (c) spur gear (d) worm geararrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
BEARINGS BASICS and Bearing Life for Mechanical Design in 10 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=aU4CVZo3wgk;License: Standard Youtube License