Automotive Technology: A Systems Approach - With Manual and Access
6th Edition
ISBN: 9781305513235
Author: ERJAVEC
Publisher: Cengage
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 40, Problem 14RQ
Which type of driving axle supports the weight of the vehicle?
a. Semifloating
b. Three-quarter floating
c. Full-floating
d. None of the above
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Which type of driving axle supports the weightof the vehicle?a. Semifloatingb. Three-quarter floatingc. Full-floatingd. None of the above
When reviewing the service procedures for CV joints and drive axles,
Technician A says that the axle can be used as a slide hammer to help remove a stubborn inboard joint from the transaxle.
Technician B says that a drive axle should never be allowed to hang by its own weight during removal or installation.
Who is correct?
O a. A only
Ob.B only
O c. Both A and B
O d. Neither A nor B
A wheel and axle transfer a force from one wheel to the axle and on to__.
A. The other wheel
B. The load
C. RPM
(answer only)
Chapter 40 Solutions
Automotive Technology: A Systems Approach - With Manual and Access
Ch. 40 - Prob. 1RQCh. 40 - What type of axle housing resembles a banjo?Ch. 40 - What type of axle merely supports the vehicle load...Ch. 40 - What type of floating axle has one wheel bearing...Ch. 40 - How are problems normally first noticed with the...Ch. 40 - In front-wheel drivetrains, the CV joint nearer...Ch. 40 - A CV joint that is capable of in-and-out movement...Ch. 40 - The double-offset joint is typically used in...Ch. 40 - Which type of joint has a flatter design than any...Ch. 40 - Which of these is the best way to determine which...
Ch. 40 - The single Cardan/Spicer universal joint is also...Ch. 40 - The drive shaft component that provides a means of...Ch. 40 - Large cars with long drive shafts often use a...Ch. 40 - Which type of driving axle supports the weight of...Ch. 40 - Which of the following describes the double-Cardan...Ch. 40 - Technician A says that a gear tooth pattern...Ch. 40 - Technician A says that limited-slip differential...Ch. 40 - Technician A says that side-bearing preload limits...Ch. 40 - Technician A says that a hunting gearset is one in...Ch. 40 - While discussing the possible causes for a...Ch. 40 - While diagnosing the cause of a clicking noise...Ch. 40 - Prob. 7ASRQCh. 40 - Technician A says that when a car is moving...Ch. 40 - While discussing different types of ring and...Ch. 40 - While reviewing the procedure for setting...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- What type of floating axle has one wheel bearing per wheel on the outside of the axle housing?arrow_forwardIn front-wheel drivetrains, the CV joint nearer the transaxle is the____. a. inner joint b. inboard joint c. outboard joint d. both a and barrow_forwardFrom the following identify a true statement regarding the adjustment of drive belt tension. а. More than 6 mm should be the correct a deflection for each belt which is under tension O b. More than 6 mm and less than 8 mm should be the correct a deflection for each belt which is under tension. c. More than 8 mm should be the correct a deflection for each belt which is under tension. O d. Less than 8 mm should be the correct a deflection for each belt which is under tensionarrow_forward
- What is the axle pressure on the front axle (which is standing on the quay)?arrow_forwardFrom the following identify a true statement regarding the adjustment of drive belt tension. a. Less than 8 mm should be the correct a deflection for each belt which is under tension b. More than 6 mm should be the correct a deflection for each belt which is under tension c. More than 8 mm should be the correct a deflection for each belt which is under tension. d. More than 6 mm and less than 8 mm should be the correct a deflection for each belt which is under tension.arrow_forwardWhen checking the fifth wheel, coupling device, the Certified Inspector must check the condition and the mounting to the frame. True or False?arrow_forward
- When reviewing the procedure for replacing an axle boot, Technician A says that the position of the old boot should be marked on the shaft before removing it. Technician B says that if the boot is dimpled or collapsed after the new boot is installed, a dulled screwdriver should be used to allow air to enter the boot. Who is correct? O a. A only O b. B only O c. Both A and B O d. Neither A nor Barrow_forwardWhen the clutch is disengauged, where does the power flow stop? Select one: a. the transmission input shaft b. the driven hub c. the pressure plate and flywheel d. the torsion springsarrow_forwardWhen trying to accommodate only axial loading, which of the following bearings is most likely to be used? a. Tapered roller bearing b. Deep groove ball bearing c. Thrust bearing d. Needle bearing e. Spherical bearingarrow_forward
- The output shaft of a reducer is bearing in bearings A and B. From deep groove ball bearings, bed A is fixed and bed B is free-formed. Which of the following is true for the inner and Outer Ring of the bearing in bearing B?Please select one: a. Because the FG force acts on the shaft, there are no forces coming to the bracelets.b. the inner ring has a point, and the Outer Ring has an environmental load.c. Environmental load affects the outer ring.d. environmental load acts on the inner ring and point load acts on the outer ring.e. both environmental and point load affect the inner ring.arrow_forwardExplain the difference between sprung and unsprung weight.arrow_forwardBased on the figure below, if wheel 4 is rotating anticlockwise, which other wheels will also rotate anticlockwise? a. Wheels 1, 2, 3, and 5 b. Wheels 1, 3, and 5 c. Wheels 2 and 5 d. None of the wheels e. None of the abovearrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Column buckling; Author: Amber Book;https://www.youtube.com/watch?v=AvvaCi_Nn94;License: Standard Youtube License