Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 11, Problem 7MC
All of the following are functions of the flywheel, except it ____ .
a. provides a mounting place for the clutch assembly
b. smooths out cylinder firing pulsations
c. has marks used to set the valve timing
d. meshes with the starter drive gear
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Which of the following is probably not the cause of avibrating clutch?a. Excessive crankshaft end playb. Out-of-balance pressure plate assemblyc. Excessive flywheel runoutd. Loose flywheel bolts
What can too much clutch pedal free play cause?
a.hard gear shifting
b.fast release bearing wear
c.release fork wear
d.clutch slipping
Which of the following screwdrivers is like a Phillips but has a flatter and blunter tip?
a.Standard
b.Torx
c.Pozidriv
d.Clutch head
Chapter 11 Solutions
Automotive Technology
Ch. 11 - Describe how to inspect an oil pump.Ch. 11 - What is the cylinder taper?Ch. 11 - Describe how to measure main bearing oil...Ch. 11 - Where does maximum cylinder bore wear occur and...Ch. 11 - List three types of compression rings.Ch. 11 - What is the purpose of a thrust main bearing?Ch. 11 - How should the oil pump be primed when installing...Ch. 11 - Most pistons used today are made of. cast iron...Ch. 11 - Cam bearings in OHV engines are typically which...Ch. 11 - Which of the following is not of concern when...
Ch. 11 - Each halt' of a split bearing is made slightly...Ch. 11 - Prob. 5MCCh. 11 - Which of the following are not typically found in...Ch. 11 - All of the following are functions of the...Ch. 11 - Which type of oil ring is slotted so that excess...Ch. 11 - When removing the balance shaft assembly:...Ch. 11 - After installing cam bearings: Technician A checks...Ch. 11 - Technician A says that a cylinder wall with too...Ch. 11 - Technician A installs a cup-type core plug with...Ch. 11 - Technician A uses a micrometer to measure the...Ch. 11 - Technician A says that piston ring end gaps should...Ch. 11 - Technician A checks crankshaft oil clearance with...Ch. 11 - When removing the piston and rod assemblies from a...Ch. 11 - Technician A says that crankshaft counterweights...Ch. 11 - Technician A uses a feeler gauge and straightedge...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Which of the following is probably not the cause of a vibrating clutch? a. Excessive crankshaft end play b. Out-of-balance pressure plate assembly c. Excessive flywheel runout d. Loose flywheel boltsarrow_forwardWhich of the following would not cause clutch binding? a. A warped clutch disc b. Improper pedal adjustment c. An oil-soaked clutch disc d. A cracked fire wallarrow_forwardwhere are the wave springs or cushion springs located in a clutch disc? a. between the drive hub and disc assembly b.on the drive hub c. between the two clutch facing d. between the rear clutch facing and pressure platearrow_forward
- Which of the following is the most likely cause for a shudder during the engagement of a lock-up torque converter? a. A bad converter b. Worn or damaged CV or U-joints c. A worn front planetary gearset d. Loose flexplatearrow_forwardIn briefly Explain why Remaining Options are incorrect. 1)The cone clutches have become obsolete because of (a) small cone angles (b) exposure to dirt and dust (c) difficulty in disengaging (d) all of thesearrow_forwardWhile inspecting a planetary gear-type final drive, Technician A says blackened pinion shafts indicate severe overloading. Technician B says bluish gears indicate overheating. Who is correct?arrow_forward
- What is the purpose of of the viscous clutch?a. to engage engine otrque to the transmission.b. to improve mobility when driving conditions become difficultc. to drive both rear driving wheels when vehicle is stuck.d. to drive the rear axle assemblyarrow_forwardwhen discussing shift problems, technician A says that worn or broken engine and transaxle mounts can cause a transaxle to have shifting problems. technician b says that poor shift boot alignment can cause a transaxle to jump out of geararrow_forwardWhen discussing shift problems,Technician A says that worn or broken engine and transaxle mounts can cause a transaxle to have shifting problems.Technician B says that poor shift boot alignment can cause a transaxle to jump out of gear?arrow_forward
- The clutch friction disc always rotates with thearrow_forwardWhile discussing a clutch alignment tool. Technician A says that the part of the tool that fits into the clutch plate must have a slightly larger OD (outside diameter) than the bore in the disc. Technician B says that the OD of the part of the tool that goes into the pilot must be slightly smaller than the ID (inside diameter) of the pilot bushing. Who is correct? Technician A Both A and B Technician B Neither A nor Barrow_forwardTechnician A says that delayed shifting can be caused by worn planetary gearset members. Technician B says that delayed shifts or slippage may be caused by leaking hydraulic circuits or sticking spool valves in the valve body. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Mechanical Design (Machine Design) Clutches, Brakes and Flywheels Intro (S20 ME470 Class 15); Author: Professor Ted Diehl;https://www.youtube.com/watch?v=eMvbePrsT34;License: Standard Youtube License