Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 43, Problem 3ASRQ
Technician A says that if the shift for all forward gears is delayed, a slipping forward clutch is normally indicated. Technician B says that a bad forward clutch is indicated when there is a slip when the transmission shifts into any forward gear. Who is correct?
a. Technician A only
b. Technician B only
c. Both A and B
d. Neither A nor B
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Technician A says that the clutch-style limited slip differential uses a multi-plate clutch pack between each side gear and the differential case. Technician B says that if the clutch discs are worn, rotating torque will be higher than specifications. Who is correct?
4) Explain the importance of a cone clutch with an application.
When discussing the various gear positions of a transfer case, Technician A says that when the transfer case is in low, the overall gear ratio is numerically increased. Technician B says that when the transfer case is in the high position, the vehicle operates in an overdrive mode due to the decrease in torque multiplication. Who is correct?
Chapter 43 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 43 - What is the most probable cause of a low fluid...Ch. 43 - What does milky colored ATF indicate?Ch. 43 - What do varnish or gum deposits on the dipstick...Ch. 43 - Typically during a pressure test, the pressure...Ch. 43 - What should you do if a valve does not move freely...Ch. 43 - Which of the following is the most likely cause...Ch. 43 - Ifa transmission does not have a dipstick, how do...Ch. 43 - What is checked during a stall test?Ch. 43 - When should the ATF level be checked on most...Ch. 43 - List five reasons for replacing a torque...
Ch. 43 - Pressure readings reveal possible problems in...Ch. 43 - Which of the following is a probable cause for a...Ch. 43 - When rebuilding an automatic transmission, which...Ch. 43 - Explain why oil circuit diagrams are invaluable...Ch. 43 - Explain how a plugged fluid cooler can cause a...Ch. 43 - Technician A says that a prerequisite to accurate...Ch. 43 - While discussing proper band adjustment...Ch. 43 - Technician A says that if the shift for all...Ch. 43 - Technician A says that the only positive way to...Ch. 43 - Technician A says that delayed shifting can be...Ch. 43 - While checking the condition of a cars ATF:...Ch. 43 - While discussing the results of an oil pressure...Ch. 43 - While discussing a pressure test: Technician A...Ch. 43 - While checking the engine and transmission mounts...Ch. 43 - While discussing the cause of aerated fluid in a...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- When a transmission is described as having two planetary gearsets in tandem, what does this mean?arrow_forwardExplain the role of shift rails and shift forks in the operation of a transmission or transaxle.arrow_forwardWhile discussing a Lepelletier system: Technician A says that two simple planetary gearsets are connected in tandem. Technician B says that these systems rely on various combinations of the planetary gears to obtain many forward gears. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
- How does a viscous clutch assembly work? Why is it used in AWD systems?arrow_forwardWhile inspecting a planetary gear-type final drive, Technician A says blackened pinion shafts indicate severe overloading. Technician B says bluish gears indicate overheating. Who is correct?arrow_forwardTo achieve a slow overdrive in a simple planetary gearset, the . a.sun gear must be the input member b.ring gear must be the input member c.planetary cart"ier must be the input memberring gear must be held d. ring gear must be heldarrow_forward
- In the operation of some automatic transmissions both blank and blank overrunning clutches are used to hold members of the planetary gearsetarrow_forwardFlat belt can be used as a clutch. Give an example of that with a diagram and explain.arrow_forwardTechnician A says that a hunting gearset is one in which one drive pinion gear tooth contacts only certain ring gear teeth, Technician B says that a partial nonhunting gearset is one in which one pinion tooth contacts only six ring gear teeth. Who is correct?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Mechanical Design (Machine Design) Clutches, Brakes and Flywheels Intro (S20 ME470 Class 15); Author: Professor Ted Diehl;https://www.youtube.com/watch?v=eMvbePrsT34;License: Standard Youtube License