Linear systems are so easy to work with that engineers often construct linear models of real (nonlinear) systems to assist in analysis and design. Such models are often surprisingly accurate over a limited range. For example, consider the simple exponential function ex. The Taylor series representation of this function is
(a) Construct a linear model for this function by truncating the Taylor series expansion alter the linear (first-order) term. (b) Evaluate your model function at x = 0.000005,.0.0005,0.05,0.5, and 5.0. (c) For which values of x does your model yield a “reasonable” approximation to ex? Explain your reasoning.
(a)
Construct a linear model for the given function by truncating the Taylor series expansion after the linear (first-order) term.
Answer to Problem 1E
Linear function for the given function is
Explanation of Solution
Given Data:
The Taylor series expansion of the given function is
Calculation:
A linear function is a simple function composed of constant terms and simple variable without exponent.
To make given function linear, remove all terms for which power of
So,
Conclusion:
Thus, linear function for the given function is
(b)
Evaluate linear function for given values of
Answer to Problem 1E
The percentage change in given function for
Explanation of Solution
Given Data:
Values of
Calculation:
The expression for percentage change in given function is as follows.
Here,
For
Substitute
Substitute
So percentage change in given function for
For
Substitute
Substitute
So percentage change in given function for
For
Substitute
Substitute
So percentage change in given function for
For
Substitute
Substitute
So percentage change in given function for
For
Substitute
Substitute
So percentage change in given function for
Conclusion:
Thus, the percentage change in given function for
(c)
For which values of
Answer to Problem 1E
The values for which the approximation yields a reasonable result is
Explanation of Solution
Calculation:
For
is
As for
Conclusion:
Thus, the values for which the approximation yields a reasonable result is
Want to see more full solutions like this?
Chapter 5 Solutions
Engineering Circuit Analysis
Additional Engineering Textbook Solutions
ANALYSIS+DESIGN OF LINEAR CIRCUITS(LL)
Fundamentals of Applied Electromagnetics (7th Edition)
Electric Motors and Control Systems
Principles Of Electric Circuits
Electrical Engineering: Principles & Applications (7th Edition)
Electric Circuits (10th Edition)
- Which of the following is not true? a.Increasing system gain increases stability b.poles farther to the left of imaginary axisimprove speed c.steady-state errors are important in the studyof unstable systems d.multiple poles on the imaginary axis improvessystem stabilityarrow_forwardPlease help with the following question. With detail on how to do it. Thank you. Given the difference equation y[n]+2y[n−1]+y[n−2] = 2x[n]−x[n−1] with initial conditions y[−1] = 3, y[−2] = 2 and a causal input x[n] =(3)^nu[n]. a) What is the order of this difference equations? b) Using the iterative method find the first 3 terms of y(n)arrow_forwardprovide justificationarrow_forward
- Which of the following statement(s) are true for a system with Kp = 99 A. The input to the system is ramp B. The system is not stable C. The Kp value will be finite for Type 1 system D. The steady state error = 0.1 E. The system is Type 0arrow_forwardEvaluate the steady state response of a series RC, where R=20 ohm and C=0.10 uF if the input voltage is 50sin(628,318.50t + 30°) V. a. 1.50 A (rms) b. 1.40 A (rms) c. 1.60 A (rms) d. 1.70 A (rms)arrow_forward. A continuous-time system is defined by an input-output relation as; y(t) = 3x(t) – 5x(t+1) Determine whether this system has the properties given below. i) Memoryless, ii) Causal, iii) Stable, iv) Linear, v) Time-invariant.arrow_forward
- The input-output relationship of the discrete time system is given as y[n] = 2x[n] + 4.5x[n+3]then determine which of these properties are hold by the system. Justify your answer.(i) Memoryless (ii) Time Invariant (iii) Linear (iv) Causal (v) Stablewarrow_forwardThe structural engineering design section within the engineering department of a regional electrical utility corporation has developed several standard designs for a group of similar transmission line towers. The detailed design for each tower is based on one of the standard designs. A transmission line project involving 50 towers has been approved. The estimated number of engineering hours needed to accomplish the first detailed tower design is 126. Assuming a 95% learning curve, a. What is your estimate of the number of engineering hours needed to design the eighth tower and to design the last tower in the project? b. What is your estimate of the cumulative average hours required for the first five designs?arrow_forwardDesign a combinational circuit with three inputs (E,L,Y) and three outputs (F,R,A). If the input is less than 5, then the output is 2 greater than the input. Otherwise, the output is 3 less than the input. if E=0 L=0 and Y=0, then if E=0 L=0 and Y=1, then if E=0 L=1 and Y=0, then if E=0 L=1 and Y=1, then…arrow_forward
- Provide the output equation, c(t). If there is a numerical answer that is nonterminating, it should be expressed up to three decimal places only The input to the system shown is a unit step function, u(t)arrow_forwardFor the Circuit shown, Let: VCC = 3.3V R1 = 85 kΩ RE = 500 Ω R2 = 35 k Ω RC = 4k Ω β = 150 Using approximation, determine the Q-point parameters: IBQ, ICQ, and VCEQ. Indicate the exact numerical values, following the given unit.arrow_forwardidentify the following 1. If the pole’s real value is positive and is located on the right side of the S-plane. The system exponentially ____________.2. Is a continuous connection of branches from one node to another with all arrowheads in the same direction.3. Knowing the location of the pole in the S-plane determines the ______________ of the system.arrow_forward
- Introductory Circuit Analysis (13th Edition)Electrical EngineeringISBN:9780133923605Author:Robert L. BoylestadPublisher:PEARSONDelmar's Standard Textbook Of ElectricityElectrical EngineeringISBN:9781337900348Author:Stephen L. HermanPublisher:Cengage LearningProgrammable Logic ControllersElectrical EngineeringISBN:9780073373843Author:Frank D. PetruzellaPublisher:McGraw-Hill Education
- Fundamentals of Electric CircuitsElectrical EngineeringISBN:9780078028229Author:Charles K Alexander, Matthew SadikuPublisher:McGraw-Hill EducationElectric Circuits. (11th Edition)Electrical EngineeringISBN:9780134746968Author:James W. Nilsson, Susan RiedelPublisher:PEARSONEngineering ElectromagneticsElectrical EngineeringISBN:9780078028151Author:Hayt, William H. (william Hart), Jr, BUCK, John A.Publisher:Mcgraw-hill Education,