Applied Fluid Mechanics
7th Edition
ISBN: 9780133414622
Author: UNTENER
Publisher: YUZU
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 5, Problem 5.2PP
A
concrete has a specific weight of
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
The density of a floating body can be determined by tying weights to the body until both the body and the weights are completely submerged, and then weighing them separately in air. Consider a wood log that weighs 1400 N in air. If it takes 34 kg of lead (? = 11,300 kg/m3) to completely sink the log and the lead in water, determine the average density of the log.
Solve Correctly
A cylinder object is suspended in a liquid at a distance of 38cm below the surface. The diameter of the object is 140cm and the density of the object is 960 kg/m3. The density ratio is 1.
Determine the height of the cylinder, if the buoyant force is 7N.
right cylindrical object has a diameter of 1526 mm and a height of 2.1m. The density of water is 1000 kg/m3. If the right cylindrical object is placed in the water, what is the buoyant force?
Chapter 5 Solutions
Applied Fluid Mechanics
Ch. 5 - The instrument package shown in Fig. 5.18 weighs...Ch. 5 - A 1.0 -m-diameter hollow sphere weighing 200 N is...Ch. 5 - A certain standard steel pipe has an outside...Ch. 5 - A cylindrical float has a 10 -in diameter and is...Ch. 5 - A buoy is a solid cylinder 0.3 m in diameter and...Ch. 5 - A float to be used as a level indicator is being...Ch. 5 - A concrete block with a specific weight of...Ch. 5 - Figure 5.19shows a pump partially submerged in oil...Ch. 5 - A steel cube 100mm on a side weighs 80N. We want...Ch. 5 - A cylindrical drum is 2 ft in diameter, 3 ft long,...
Ch. 5 - If the aluminum weights described in Problem 5.10...Ch. 5 - Figure 5.20 shows a cube floating in a fluid....Ch. 5 - A hydrometer is a device for indicating the...Ch. 5 - For the hydrometer designed in Problem 5.13 what...Ch. 5 - For the hydrometer designed in Problem 5.13 , what...Ch. 5 - A buoy is to support a cone-shaped instrument...Ch. 5 - A cube has side dimensions of 18.00 in. It is made...Ch. 5 - A cube has side dimensions of 18.00 in. It is made...Ch. 5 - A ship has a mass of 292 Mg. Compute the volume of...Ch. 5 - An iceberg has a specific weight of 8.72kN/m3....Ch. 5 - A cylindrical log has a diameter of 450 mm and a...Ch. 5 - The cylinder shown in Fig. 5.23 is made from a...Ch. 5 - If the cylinder from Problem 5.22 is placed in...Ch. 5 - A brass weight is to be attached to the bottom of...Ch. 5 - For the cylinder with the added brass (described...Ch. 5 - For the composite cylinder shown in Fig. 5.25 what...Ch. 5 - A vessel for a special experiment has a hollow...Ch. 5 - A light foam cup similar to a disposable coffee...Ch. 5 - A light foam cup similar to a disposable coffee...Ch. 5 - Repeat Problem 5.29, but consider that the steel...Ch. 5 - Figure 5.27 shows a raft made of four hollow drums...Ch. 5 - Figure 5.28 shows the construction of the platform...Ch. 5 - For the raft shown in Fig. 5.27, how much of the...Ch. 5 - For the raft and platform shown in Figs. 5.27 and...Ch. 5 - A float in an ocean harbor is made from a uniform...Ch. 5 - Describe how the situation described in Problem...Ch. 5 - A cube 6.00 in on a side is made from aluminum...Ch. 5 - Prob. 5.38PPCh. 5 - A cylindrical block of wood is 1.00 m in diameter...Ch. 5 - A container for an emergency beacon is a...Ch. 5 - The large platform shown in Fig. 5.29 carries...Ch. 5 - Will the cylindrical float described in Problem...Ch. 5 - Will the buoy described in Problem 5.5 be stable...Ch. 5 - Will the float described in Problem 5.6 be stable...Ch. 5 - A closed, hollow, empty drum has a diameter of...Ch. 5 - Figure 5.30 shows a river scow used to carry bulk...Ch. 5 - Prob. 5.47PPCh. 5 - For the vessel shown in Fig. 5.26and described in...Ch. 5 - For the foam cup described in Problem 5.28, will...Ch. 5 - Referring to Problem 5.29, assume that the steel...Ch. 5 - Referring to Problem 5.30, assume that the steel...Ch. 5 - Prob. 5.52PPCh. 5 - Will the cylinder together with the brass plate...Ch. 5 - A proposed design for a part of a seawall consists...Ch. 5 - A platform is being designed to support some water...Ch. 5 - Prob. 5.56PPCh. 5 - A barge is 60 ft long, 20 ft wide, and 8 ft deep....Ch. 5 - If the barge in Problem 5.57 is loaded with 240000...Ch. 5 - A piece of cork having a specific weight of...Ch. 5 - Figure 5.20 shows a cube floating in a fluid, (a)...Ch. 5 - A boat is shown in Fig. 5.33(a). Its geometry at...Ch. 5 - (a) If the cone shown in Fig. 5.34 is made of pine...Ch. 5 - Refer to Fig. 5.35. The vessel shown is to be used...Ch. 5 - Prob. 5.64PPCh. 5 - Wetsuits are prohibited in some triathlons due to...Ch. 5 - A cylinder that is 500 mm in diameter and 2.0 m...Ch. 5 - The diving bell shown in Fig. 5.2 weighs 72 kN and...Ch. 5 - Prob. 5.68PPCh. 5 - A scuba diver with wet suit, tank, and gear has a...Ch. 5 - Prob. 5.70PPCh. 5 - Does steel float? It has a specific gravity of...Ch. 5 - Prob. 5.72PPCh. 5 - An undersea camera (Figure 5.36 ) is to hang from...Ch. 5 - Work Problem 5.73 again, but this time the camera...Ch. 5 - Write a program for evaluating the stability of a...Ch. 5 - For any cylinder of a uniform density floating in...Ch. 5 - For the results found in Project 2, compute the...Ch. 5 - Write a program for evaluating the stability of a...Ch. 5 - Write a program for determining the stability of a...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
Select a mechanical component from Part 3 of this book (roller bearings, springs, etc.), go to the Internet, an...
Shigley's Mechanical Engineering Design (McGraw-Hill Series in Mechanical Engineering)
3.3 It is known that a vertical force of 200 lb is required to remove the nail at C from the board. As the nail...
Vector Mechanics for Engineers: Statics
A number of common substances are
Some of these materials exhibit characteristics of both solid and fluid beha...
Fox and McDonald's Introduction to Fluid Mechanics
Consider a subsonic compressible flow in cartesian coordinates where the velocity potential is given by (x,y)=V...
Fundamentals of Aerodynamics
A biological fluid moves at a flow rate of m=0.02kg/s through a coiled, thin-walled, 5-mm-diameter tube submerg...
Fundamentals of Heat and Mass Transfer
19.8 Calculate the allowable tensile load for the connection shown. The plates are ASTM A36 steel and the weld ...
Applied Statics and Strength of Materials (6th Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- One side of the container has a 03-m square door that is hinged at its top edge. If the container is filled with water, determine the smallest force F that must be applied to the bottom edge of the door to keep it closed.arrow_forwardThe thin-walled cylindrical can with a spherical dimple weighs 0.2 lb. Determine the force P required to push the can into water to a depth of 8 in. Use =0.036lb/in.3 for water.arrow_forwardThe weight of the cylindrical tank is negligible in comparison to the weight of water it contains (water weighs 62.4lb/ft3). The coefficient of static friction between the tank and the horizontal surface is s. (a) Assuming a full tank, find the smallest force P required to tip the tank, and the smallest s that would allow tipping to take place. (b) If the force P = 200 lb initiates tipping, determine the depth of water in the tank.arrow_forward
- An elliptical plate, major axis 6 feet and minor axis 4 feet, is submerged vertically until its minor axis lies in the surface of the water (weight density =p Ib/fr3). Determine the appropriate integral to be used to determine the force on one side of the submergedarrow_forwardAn oil tanker 3m wide 2 m deep and 10 m long contains oil of density 800 kg/m3, if the tanker is closed and completely filled with the oil and accelerated horizontally at 3m/s2. a.) determine the total liquid thrust (hydrostatic force) on the front end. (in kN) b.) determine the total liquid thrust (hydrostatic force) on the rear end. (in kN)arrow_forwardA cylindrical tank 2m diameter and 4 m long, with its axis horizontal, is half filled with water and half filled with oil of density 880 kg/m3. Determine the location of the hydrostatic force from the top of the cylinder. Express your answer in two decimal place and in terms of m.arrow_forward
- A block of wood floats in water with 45 mm projecting above the water’s surface. When placed in glycerine of Relative Density (RD) 1.34, the block projects 70 mm above the surface of that liquid. Determine the density of the woodarrow_forwardDetermine the buoyant force on a 800 ft3 balloon at an altitude of 500 ft. Give the direction of this force.arrow_forwardAn open cubic tank of side length 2 m is completely filled with water. If the surface of the water and the outside of the tank are subject to atmospheric pressure, what are the hydrostatic forces acting on: Each side of the tank? The base of the tank?arrow_forward
- A 1-kg cube of wood floats in an upright position in fresh water. If a side of the cube measures 12.5 cm, determine the pressure acting at the bottom of the cube due to the water. How deep is the cube floating?arrow_forwardA block of wood floats in water with 2 inches projecting above the water surface. When placed in glycerin of relative weight 1.26, the block floats 3 inches above the liquid. Determine the weight density of the wood.arrow_forwardA 10cm x 10 cm x 10cm block of steel (ρsteel = 7900 kg/m3) is suspended from a spring scale. The scale is in Newtons. a. What is the scale reading if the block is in air? b. What is the scale reading after the block has been lowered into a beaker of water and is completely submerged?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- International Edition---engineering Mechanics: St...Mechanical EngineeringISBN:9781305501607Author:Andrew Pytel And Jaan KiusalaasPublisher:CENGAGE L
International Edition---engineering Mechanics: St...
Mechanical Engineering
ISBN:9781305501607
Author:Andrew Pytel And Jaan Kiusalaas
Publisher:CENGAGE L
Physics 33 - Fluid Statics (1 of 10) Pressure in a Fluid; Author: Michel van Biezen;https://www.youtube.com/watch?v=mzjlAla3H1Q;License: Standard YouTube License, CC-BY