Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 50, Problem 7ASRQ
Vehicle dynamics during braking are being discussed: Technician A says that the rear of the car rises during braking. Technician B says that the front of the car lowers during braking. Who is correct?
- Technician A only
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Technician A days that a weak suspension spring can cause a loss of traction during acceleration. Technician B says that a weak suspension spring can cause poor braking power. Who is correct?
Technician A says that on FWD vehicles, the front wheels toe-out while the rear wheels on an independent suspension try to toe-in as the vehicle moves ahead. Technician B says that on RWD vehicles, the front wheels tend to toe-in while the rear wheels toe-out in response to rolling resistance as suspension compliance. Who is correct?
Technician A says the size of the pads, shoes, drums, and rotors is based on the weight of the vehicle. Technician B says their size is based on the top speed the vehicle can achieve. Who is correct?
a. A only b. B only c. both A and B d. neither A nor B
If a force of 150 pounds is applied to a master cylinder with a piston area of 1 square inch, how much force is developed on a wheel cylinder that has a piston area of 2 square inches?
a. 75 pounds b. 150 pounds c. 300 pounds d. 450 pounds
While manually bleeding a brake system, Technician A loosens all the brake bleeder screws at the same time. Technician B uses shop air to push the fluid and air through the lines and out the bleeder screws. Who is correct?
a. A only b. B only c. both A and B d. neither A nor B
Brake fluid serves as a lubricant for the parts of the hydraulic system and ensures smooth and even operation.
a. True b. False
Chapter 50 Solutions
Automotive Technology
Ch. 50 - Explain why bleeding air out of a hydraulic system...Ch. 50 - Explain why modern hydraulic braking systems are...Ch. 50 - Describe the functions of the hydraulic system...Ch. 50 - When the brakes are applied on a moving car, the...Ch. 50 - What is the purpose of the master cylinder vent...Ch. 50 - Explain why a height-sensing proportioning valve...Ch. 50 - A three-function combination valve has a brake...Ch. 50 - Explain how vacuum is used to provide a power...Ch. 50 - True or False? Metering and proportioning valves...Ch. 50 - True or False? Semimetallic brake pads still often...
Ch. 50 - The purpose of the master cylinder is to. generate...Ch. 50 - Which of the following can lead to brake hose...Ch. 50 - Which type of brake requires greater application...Ch. 50 - Which of the following is not a factor in...Ch. 50 - Which of the following could cause an extremely...Ch. 50 - A vehicles power brakes are grabbing: Technician A...Ch. 50 - While discussing what affects the amount of...Ch. 50 - The metering valve portion of a combination valve...Ch. 50 - While discussing quick take-up master cylinders:...Ch. 50 - While bleeding a brake system: Technician A...Ch. 50 - The basic frictional parts of a brake system are...Ch. 50 - Vehicle dynamics during braking are being...Ch. 50 - Pressure bleeding is being discussed: Technician A...Ch. 50 - Technician A says that the master cylinder should...Ch. 50 - The hydraulic system of the hydro-boost and...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Besides indicating ABS faults for some systems, the red brake warning lamp on the instrument panel can indicate failure of the brake system, application of the brake, or low fluid level in the.arrow_forwardWhich of the following would not cause noise while driving in 2WD under a heavy throttle? a. Faulty ignition switch b. Worn transfer case clutch c. Inoperative locking hubs d. Bad front half shaftarrow_forwardWhile discussing pull during braking: Technician A says that this can be caused by one tire being underinflated. Technician B says that a frozen wheel cylinder on one side of the car can cause this. Who is correct? Technician A only Technician B only Both A and B Neither A nor Barrow_forward
- Technician A says the size of the pads, shoes, drums, and rotors is based on the weight of the vehicle. Technician B says their size is based on the top speed the vehicle can achieve. Who is correct? a. A only b. B only c. both A and B d. neither A nor B If a force of 150 pounds is applied to a master cylinder with a piston area of 1 square inch, how much force is developed on a wheel cylinder that has a piston area of 2 square inches? a. 75 pounds b. 150 pounds c. 300 pounds d. 450 pounds While manually bleeding a brake system, Technician A loosens all the brake bleeder screws at the same time. Technician B uses shop air to push the fluid and air through the lines and out the bleeder screws. Who is correct? a. A only b. B only c. both A and B d. neither A nor B Brake fluid serves as a lubricant for the parts of the hydraulic system and ensures smooth and even operation. a. True b. False Rusted-through brake lines are uncommon. a. True b. False A technician is diagnosing a vehicle with…arrow_forwardWhat is a suspension system.arrow_forwardDiscuss about antilock braking system and its importance in modern vehicles?arrow_forward
- True or False? Disc brakes are not as likely to fade during heavy braking as are drum brakes.arrow_forwardAn owners concern indicates excessive play in the steering wheel: Technician A checks the steering shaft U-joints. Technician B performs a dry park check of the linkage. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardTechnician A says that the suspension switch must be turned off before raising any corner of a car with an electronic air suspension. Technician B says that the ignition switch must not be turned on while any corner of a car with electronic air suspension is raised. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
- Which of the following is part of the sprung weight of a vehicle? a. Steering linkage b. Tires c. Engine d. All of the abovearrow_forwardIn a racing situation suspension plays a completely another role what is that?arrow_forwardDescribe how to test the parking brake system in late model vehicles.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Dynamics - Lesson 1: Introduction and Constant Acceleration Equations; Author: Jeff Hanson;https://www.youtube.com/watch?v=7aMiZ3b0Ieg;License: Standard YouTube License, CC-BY