Activities Manual for Programmable Logic Controllers
5th Edition
ISBN: 9781259679568
Author: Petruzella, Frank
Publisher: MCGRAW-HILL HIGHER EDUCATION
expand_more
expand_more
format_list_bulleted
Question
thumb_up100%
Chapter 6, Problem 1P
Program Plan Intro
NC pushbutton switch:
- The abbreviation NC stands for a Normally Closed pushbutton switch.
- It will be initially at closed contact and will be opened when the switch or coil is energized.
- It opens a circuit when it is pressed and return back to its closed condition when it is released.
- An electrical symbol used to represent NC pushbutton switch is given below
Given:
The conventional hardwired relay circuit should perform the following circuit functions when a NC pushbutton is pressed.
- The pilot light must be switched ON.
- The solenoid must be de-energized.
- Motor running should be started.
- Sound a horn.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
The input waveform shown in the figure below is applied to an inverter, which is used to
operate a light on a control circuit. Draw the timing diagram of the output waveform in
proper relation to the input.
VIN
HIGH
LOW
urr
What is the resistance of a circuit in which a load that draws 3 A is connected to a 24 V supply?
Design and upload a circuit where each time PB1 is pressed and released, data file D0020 in
Chapter 6 Solutions
Activities Manual for Programmable Logic Controllers
Ch. 6 - Prob. 1RQCh. 6 - Prob. 2RQCh. 6 - Prob. 3RQCh. 6 - Prob. 4RQCh. 6 - Prob. 5RQCh. 6 - Prob. 6RQCh. 6 - Prob. 7RQCh. 6 - Prob. 8RQCh. 6 - What do the abbreviations NO and NC represent when...Ch. 6 - Prob. 10RQ
Ch. 6 - Prob. 11RQCh. 6 - Prob. 12RQCh. 6 - Compare the operation of a photovoltaic solar cell...Ch. 6 - What are the two basic components of a...Ch. 6 - Prob. 15RQCh. 6 - Give an explanation of how a scanner and a decoder...Ch. 6 - Prob. 17RQCh. 6 - Prob. 18RQCh. 6 - Prob. 19RQCh. 6 - Prob. 20RQCh. 6 - Prob. 21RQCh. 6 - Prob. 22RQCh. 6 - Prob. 23RQCh. 6 - Prob. 24RQCh. 6 - Prob. 25RQCh. 6 - Prob. 26RQCh. 6 - Prob. 27RQCh. 6 - Prob. 28RQCh. 6 - Prob. 29RQCh. 6 - Prob. 30RQCh. 6 - Prob. 31RQCh. 6 - Prob. 32RQCh. 6 - Prob. 33RQCh. 6 - Prob. 1PCh. 6 - Prob. 2PCh. 6 - Prob. 3PCh. 6 - Prob. 4PCh. 6 - Design a PLC program and prepare a typical I/O...Ch. 6 - Prob. 6PCh. 6 - Prob. 7PCh. 6 - Prob. 8P
Knowledge Booster
Similar questions
- Arduino programming exercises using Uno Microcontroller Write a program that turns on an LED attached to pin 3 for 5 seconds then turns it off. The light should stay off for 3 seconds and then the LED should blink 10 times at a rate of 1 Hz (on and off each second).arrow_forwardIn a certain chemical-processing plant, a liquid chemical is used in a manufacturing process. The chemical is stored in three different tanks. A level sensor in each tank produces a HIGH voltage when the level of chemical in the tank drops below a specified point. Design a circuit that monitors the chemical level in each tank and indicates when the level in any two of the tanks drops below the specified point.arrow_forwardQ1 Using a multiplexer design a combinational circuit design defined by the following boolean expression: F= y'z'+x'y+yzarrow_forward
- Depending on the value of input and reference voltage a comparator can be named asarrow_forwardA taco generator is use as a sensor to detect the speed of a rotating motor. The o/p of the tacho is between Ov and 5v where the midrange (2.5v) is equivalent to that the motor is standstill. When motor accelerates CW toward full speed, the tacho o/p will vary from 2.5v to 5v and when the input of tacho varies from 2.5v down to Ov means the motor is accelerating towards cCW. The Scenario is to reflect the equivalent speed on two SSDS which one will read the equivalent speed of reading 5 for maximum Cw (5v) and the other will also read 5 for maximum CCW (Ov) equivalent speed in the reverse direction. Taco generator input is connected to PA4, the CW SSD on PORTB and the CCW SD on PORTC Write ATmega 16 program sketch to follow the above scenario REFS1 REFSO Voltage Reference Selection AREF, Internal Vref turned off AVCC with external capacitor at AREF pin 1 Reserved 1 Internal 2.56V Voltage Reference with external capacitor at AREF pin ADPS2 ADPS1 ADPSO Division Factor 2 1 1 1 1 16 1 32 1…arrow_forwardDesign an appropriate combinational circuit that implements a digital system with the following output functions an AC remote: ON, OFF, MODE, SHIFT, FAN, SMART, SWING, ECO using a decoder.arrow_forward
- Draw the symbols for a Normally Open (NO) limit switch and a Normally Closed (NC) limit switch, both in the un-actuated and actuated states.arrow_forwardA digital system has a clock generator that produces pulses at a frequency of 80 MHz. Design a circuit that provides a clock with a cycle time of 50 ns.arrow_forwardWhat are the steps in designing a combinational circuit?arrow_forward
- Design a circuit that converts (BCD) code to Gray code.arrow_forwardStepper motor control using ULN2003 IC in 16F877 microcontroller will be carried out. In the program, stepper motor and driver IC will be connected to PORTD. to RA0 pin When the connected button is pressed, the stepper motor will turn to the left with half a step and one speed, to pin RA1. When the connected button is pressed, the motor will turn to the right at a certain speed. button connected to RA2 pin When pressed, the motor will be stopped no matter which direction it turns. During engine operation (right or left) If the button connected to the RA3 pin is pressed, the motor speed will double. Working logic Write the program described (solve with ccs)arrow_forwardCna you draw the circuit in a paper a better one to understand?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Systems ArchitectureComputer ScienceISBN:9781305080195Author:Stephen D. BurdPublisher:Cengage Learning
Systems Architecture
Computer Science
ISBN:9781305080195
Author:Stephen D. Burd
Publisher:Cengage Learning