Activities Manual for Programmable Logic Controllers
5th Edition
ISBN: 9781259679568
Author: Petruzella, Frank
Publisher: MCGRAW-HILL HIGHER EDUCATION
expand_more
expand_more
format_list_bulleted
Concept explainers
Expert Solution & Answer
thumb_up100%
Chapter 6, Problem 8RQ
Explanation of Solution
Comparison on the method of operation of different switches:
Based on the operational point of view, switches are divided into three types as follows:
- Manually operated switch
Mechanically operated switch- Proximity switch
Manually operated switch | Mechanically operated switch | Proximity switch |
Manually operated switches are controlled by hand. | Mechanically operated switches are automatically controlled by parameters such as pressure, position, or temperature. | Proximity switches does not need any physical contact to sense the presence or absence of a target. |
These include toggle switches, pushbuttons switches, selector switches, Push button switches are most commonly used as manually operated switches... |
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Q. No.6 : An alarm system has three different control panels in three different locations. To enable the system, switches in at least two of the panels must be in the on position. If fewer than two are in the on position, the system is disabled. Design a circuit to control the switches.
1. Refer to the circuit shown in Figure 27–2. Would it be possible to replace the hand-off-auto switch in this circuit with a hand-off-auto switch that contained a common terminal and center Off position like the HOA switch shown in Figure 27–1? Explain your answer.
In DC power Supply Unit the function of transformer is to Convert 230V AC into Lower Dc Voltage
Select one:
O True
O False
Chapter 6 Solutions
Activities Manual for Programmable Logic Controllers
Ch. 6 - Prob. 1RQCh. 6 - Prob. 2RQCh. 6 - Prob. 3RQCh. 6 - Prob. 4RQCh. 6 - Prob. 5RQCh. 6 - Prob. 6RQCh. 6 - Prob. 7RQCh. 6 - Prob. 8RQCh. 6 - What do the abbreviations NO and NC represent when...Ch. 6 - Prob. 10RQ
Ch. 6 - Prob. 11RQCh. 6 - Prob. 12RQCh. 6 - Compare the operation of a photovoltaic solar cell...Ch. 6 - What are the two basic components of a...Ch. 6 - Prob. 15RQCh. 6 - Give an explanation of how a scanner and a decoder...Ch. 6 - Prob. 17RQCh. 6 - Prob. 18RQCh. 6 - Prob. 19RQCh. 6 - Prob. 20RQCh. 6 - Prob. 21RQCh. 6 - Prob. 22RQCh. 6 - Prob. 23RQCh. 6 - Prob. 24RQCh. 6 - Prob. 25RQCh. 6 - Prob. 26RQCh. 6 - Prob. 27RQCh. 6 - Prob. 28RQCh. 6 - Prob. 29RQCh. 6 - Prob. 30RQCh. 6 - Prob. 31RQCh. 6 - Prob. 32RQCh. 6 - Prob. 33RQCh. 6 - Prob. 1PCh. 6 - Prob. 2PCh. 6 - Prob. 3PCh. 6 - Prob. 4PCh. 6 - Design a PLC program and prepare a typical I/O...Ch. 6 - Prob. 6PCh. 6 - Prob. 7PCh. 6 - Prob. 8P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.Similar questions
- Arduino programming exercises using Uno Microcontroller Write a program that turns on an LED attached to pin 3 for 5 seconds then turns it off. The light should stay off for 3 seconds and then the LED should blink 10 times at a rate of 1 Hz (on and off each second).arrow_forwardAnswer these questions please. Ctrarrow_forwardThere are two lamps used to illuminate the well, the first lamp is installed at the top of the wellI, and the second lamp is installed at a distance from the first using the Arduino board. Make the two lamps light at the same time using only one switcharrow_forward
- traffic light is installed at a junction of a railroad and a road. the traffic light is controlled by two switches in the rails placed one mile apart on either side of the junction. a switch is turned on when the train is over it and is turned off otherwise. the traffic light changes from green (logic 0) to red (logic 1) when the beginning of the train is one mile from the junction. the light changes back to green when the end of the train is one mile away from the junction. all trains are less than 2 miles long. Draw circuit diagramarrow_forwardDraw the truth table,according to the given below The alarm circuit in a car is controlled by 5 switches. These are:A: ignition switch, B: driver,C: driver's belt, D: front passenger andE: front passenger belt. Switches are initially in the off state. Switch A opens in the ignitionstate. When the person sits, the relevant key opens. If the belt isattached, the relevant key opens. Design the circuit that will alarmwhen the car is moving and any of the front seats are occupied and theseat belt is not fastened.arrow_forwardDefine Watch Dog Timer.arrow_forward
- Find the nodal voltages of the circuit shown below. 20hms. MVarrow_forwardConvert the state diagram given below to ASM chart. Additionally, implement the control circuit using multiplexors. A/1 00 01, 10 11 11. C/O 01,10 00 ó1,10 B/0 11 00arrow_forwardDraw a ladder diagram that will have the following results: a. Lamp L2 and Lamp L3 deactivated while Lamp L1 activated the moment power is turned ON. b. Lamp L1 and Lamp L3 deactivated while Lamp L2 activated when switch S2 is pressed and released. c. Lamp L1 and Lamp L2 deactivated while Lamp L3 activated when switch S3 is pressed and released. d. Lamp L2 and Lamp L3 deactivated while Lamp L1 activated when switch S1 is pressed and released.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Systems ArchitectureComputer ScienceISBN:9781305080195Author:Stephen D. BurdPublisher:Cengage Learning
Systems Architecture
Computer Science
ISBN:9781305080195
Author:Stephen D. Burd
Publisher:Cengage Learning