Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 6, Problem 21RQ
While discussing a clutch alignment tool. Technician A says that the part of the tool that fits into the clutch plate must have a slightly larger OD (outside diameter) than the bore in the disc. Technician B says that the OD of the part of the tool that goes into the pilot must be slightly smaller than the ID (inside diameter) of the pilot bushing. Who is correct?
- Technician A
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
technician a says that an oil-soaked clutch dis can cause clutch chatter technician b says that clutch chatter can be caused by the loose bell housing bolts
A car jumps out of gear into neutral, particularlywhen decelerating or going down hills: Technician Achecks the shift lever and external gearshift linkagefirst. Technician B says that the clutch pilot bearingcould be the problem. Who is correct?a. Technician A onlyb. Technician B onlyc. Both A and Bd. Neither A nor B
Which of the following screwdrivers is like a Phillips but has a flatter and blunter tip?
a.Standard
b.Torx
c.Pozidriv
d.Clutch head
Chapter 6 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 6 - Explain why testlights are not recommended for...Ch. 6 - True or False? A compression gauge will show the...Ch. 6 - Name the two basic types of compression gauges.Ch. 6 - What tool is used to test engine manifold vacuum.Ch. 6 - Prob. 5RQCh. 6 - Technician A says that a brake drum micrometer has...Ch. 6 - Technician A says that a pyrometer measures...Ch. 6 - True or False? A lab scope is a visual voltmeter...Ch. 6 - Prob. 9RQCh. 6 - Technician A uses a digital volt/ohmmeter to test...
Ch. 6 - Technician A says that a charging station removes...Ch. 6 - Which of the following statements about manifold...Ch. 6 - True or False? A brake shoe adjusting gauge is an...Ch. 6 - When conducting an oil pressure test: Technician A...Ch. 6 - Which of the following conditions can be revealed...Ch. 6 - Technician A uses a high-impedance testlight on...Ch. 6 - Technician A says that a sulfated and plugged fuel...Ch. 6 - The tests conducted by a scan tool can also be...Ch. 6 - When using a fuel injector pulse tester....Ch. 6 - To measure engine cranking current, a DNIM...Ch. 6 - While discussing a clutch alignment tool....Ch. 6 - True or False? The angle of the drive shaft at the...Ch. 6 - Technician A says that ball joints may be pressed...Ch. 6 - Which of the following is not a suitable way to...Ch. 6 - Prob. 25RQ
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A car jumps out of gear into neutral, particularly when decelerating or going down hills: Technician A checks the shift lever and external gearshift linkage first. Technician B says that the clutch pilot bearing could be the problem. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardWhile discussing the purpose of a clutch pressure plate: Technician A says that the pressure plate assembly squeezes the clutch disc onto the flywheel. Technician B says that the pressure plate moves away from the clutch disc so that the disc can stop rotating. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardAll of the following are functions of the flywheel, except it ____ . a. provides a mounting place for the clutch assembly b. smooths out cylinder firing pulsations c. has marks used to set the valve timing d. meshes with the starter drive geararrow_forward
- Technician A says that if the shift for all forward gears is delayed, a slipping forward clutch is normally indicated. Technician B says that a bad forward clutch is indicated when there is a slip when the transmission shifts into any forward gear. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardWhich of the following is the most likely cause for a shudder during the engagement of a lock-up torque converter? a. A bad converter b. Worn or damaged CV or U-joints c. A worn front planetary gearset d. Loose flexplatearrow_forwardTechnician A says that delayed shifting can be caused by worn planetary gearset members. Technician B says that delayed shifts or slippage may be caused by leaking hydraulic circuits or sticking spool valves in the valve body. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
- While discussing ways to determine if a pilot bushing is faulty: Technician A says that if it operated quietly, it does not need to be replaced. Technician B says that a careful inspection of the transmissions input shaft can determine the condition of the pilot bushing. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardWhich of the following is probably not the cause of a vibrating clutch? a. Excessive crankshaft end play b. Out-of-balance pressure plate assembly c. Excessive flywheel runout d. Loose flywheel boltsarrow_forwardTechnician A says that the clutch-style limited slip differential uses a multi-plate clutch pack between each side gear and the differential case. Technician B says that if the clutch discs are worn, rotating torque will be higher than specifications. Who is correct?arrow_forward
- Which of the following screwdrivers is like a Phillipsbut has a flatter and blunter tip?a. Standardb. Torx®c. Pozidriv®d. Clutch headarrow_forwardWhen the clutch pedal is released on a hydraulic clutch linkage, the ------• a. master cylinder piston is released by spring tension b. master cylinder piston is released by hydraulic pressure c. slave cylinder is released by hydraulic pressure d. slave cylinder piston does not movearrow_forwardWhat is the purpose of of the viscous clutch?a. to engage engine otrque to the transmission.b. to improve mobility when driving conditions become difficultc. to drive both rear driving wheels when vehicle is stuck.d. to drive the rear axle assemblyarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Mechanical Design (Machine Design) Clutches, Brakes and Flywheels Intro (S20 ME470 Class 15); Author: Professor Ted Diehl;https://www.youtube.com/watch?v=eMvbePrsT34;License: Standard Youtube License