Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Question
Chapter 6, Problem 4MC
To determine
The technician with correct approach.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
While testing variable resistors: Technician A saysthat while checking a rheostat with a voltmeter, thevoltage should change smoothly with a change in thecontrol. Technician B says that a potentiometer canbe checked with a scope. Who is correct?a. Technician Ab. Technician Bc. Both A and Bd. Neither A nor B
In anodizing process the cathode is used to complete the circuit only.
Select one:
True
False
Basically a NC machine runs on a program fed to it through Punched tapes
Select one:
True
False
Chapter 6 Solutions
Automotive Technology
Ch. 6 - Explain why testlights are not recommended for...Ch. 6 - Name the two basic types of compression gauges.Ch. 6 - What tool is used to test engine manifold vacuum.Ch. 6 - Describe two methods of trapping asbestos/brake...Ch. 6 - True or False? A compression gauge will show the...Ch. 6 - True or False? A lab scope is a visual voltmeter...Ch. 6 - True or False? A brake shoe adjusting gauge is an...Ch. 6 - Prob. 1MCCh. 6 - Technician A says that a brake drum micrometer has...Ch. 6 - Technician A says that a pyrometer measures...
Ch. 6 - Prob. 4MCCh. 6 - Technician A uses a digital volt/ohmmeter to test...Ch. 6 - Technician A says that a charging station removes...Ch. 6 - Which of the following statements about manifold...Ch. 6 - When conducting an oil pressure test: Technician A...Ch. 6 - Which of the following conditions can be revealed...Ch. 6 - Technician A uses a high-impedance testlight on...Ch. 6 - Technician A says that a sulfated and plugged fuel...Ch. 6 - The tests conducted by a scan tool can also be...Ch. 6 - When using a fuel injector pulse tester....Ch. 6 - To measure engine cranking current, a DNIM...Ch. 6 - While discussing a clutch alignment tool....Ch. 6 - Technician A says that ball joints may be pressed...Ch. 6 - Which of the following is not a suitable way to...Ch. 6 - Prob. 18MC
Knowledge Booster
Similar questions
- Technician A uses a testlight to test circuit protection devices. Technician B uses a voltmeter to test circuit protection devices. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTechnician A uses a testlight to detect resistance. Technician B uses a jumper wire to test circuit breakers, relays, and lights. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhile measuring the resistance of a wire with an ohmmeter: Technician A says that if low resistance is shown on the meter, the wire is shorted. Technician B says that if no resistance is measured, the wire is shorted. Who is correct? Technician A Technician B Both A and B d. Neither A nor Barrow_forward
- True or False? A zero reading on an ohmmeter means the circuit or component is open.arrow_forwardWhile measuring resistance: Technician A uses an ohmmeter to measure resistance of a component before disconnecting it from the circuit. Technician B uses a voltmeter to measure voltage drop. A circuit with very low resistance will drop zero or very little voltage. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhile checking an A/C compressor clutch coil clamping diode with a DMM, the meter shows infinite resistance when the diode is measured in both directions: Technician A says that the diode is open. Technician B says that all diodes should behave this way until a specified voltage is applied to them. Who is correct? a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forward
- Technician A uses a digital volt/ohmmeter to test amperage. Technician B uses the same tool to test resistance. Who is correct? Technician A Both A and B Technician B Neither A nor Barrow_forwardWhile discussing the AWG system: Technician A says that most automotive wiring range from 0 to 4 gauge. Technician B says that the higher the gauge number, the larger the diameter of the wire. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhich of the following tests would not be performed to check for high resistance in the battery' cables? Cranking voltage test Insulated circuit resistance test Starter relay by-pass test Ground circuit resistance testarrow_forward
- While diagnosing the location of a wire-to-wire short: Technician A checks the wiring of the affected circuits for signs of burned insulation and melted conductors. Technician B checks common connectors shared by the two affected circuits. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhile testing variable resistors: Technician A says that while checking a rheostat with a voltmeter, the voltage should change smoothly with a change in the control. Technician B says that a potentiometer can be checked with a scope. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTrue or False? The same information available in service manuals and bulletins may also be available electronically on DVDs and the Internet.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning