PROGRAMMABLE LOGIC CONTROLLERS (LL)
5th Edition
ISBN: 9781260844146
Author: Petruzella
Publisher: MCG
expand_more
expand_more
format_list_bulleted
Concept explainers
Expert Solution & Answer
thumb_up100%
Chapter 6, Problem 8RQ
Explanation of Solution
Comparison on the method of operation of different switches:
Based on the operational point of view, switches are divided into three types as follows:
- Manually operated switch
Mechanically operated switch- Proximity switch
| Manually operated switch | Mechanically operated switch | Proximity switch |
| Manually operated switches are controlled by hand. | Mechanically operated switches are automatically controlled by parameters such as pressure, position, or temperature. | Proximity switches does not need any physical contact to sense the presence or absence of a target. |
| These include toggle switches, pushbuttons switches, selector switches, Push button switches are most commonly used as manually operated switches... |
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Write an Arduino program to make LED connected at pin(5) turnON,when pressed on first switch and turn "OFF" after press second switch,the two switches are connected on pin(7) and pin(8) respectively,draw thecircuit diagram.
Using the sim8085 write the following code:
In a sensor network, three pressure sensors are connected which gives the reading of 4 psi, 8 psi and 10 psi. All the sensor readings are to be summed up and store as a single reading
1. Refer to the circuit shown in Figure 27–2. Would it be possible to replace the hand-off-auto switch in this circuit with a hand-off-auto switch that contained a common terminal and center Off position like the HOA switch shown in Figure 27–1? Explain your answer.
Chapter 6 Solutions
PROGRAMMABLE LOGIC CONTROLLERS (LL)
Ch. 6 - Prob. 1RQCh. 6 - Prob. 2RQCh. 6 - Prob. 3RQCh. 6 - Prob. 4RQCh. 6 - Prob. 5RQCh. 6 - Prob. 6RQCh. 6 - Prob. 7RQCh. 6 - Prob. 8RQCh. 6 - What do the abbreviations NO and NC represent when...Ch. 6 - Prob. 10RQ
Ch. 6 - Prob. 11RQCh. 6 - Prob. 12RQCh. 6 - Compare the operation of a photovoltaic solar cell...Ch. 6 - What are the two basic components of a...Ch. 6 - Prob. 15RQCh. 6 - Give an explanation of how a scanner and a decoder...Ch. 6 - Prob. 17RQCh. 6 - Prob. 18RQCh. 6 - Prob. 19RQCh. 6 - Prob. 20RQCh. 6 - Prob. 21RQCh. 6 - Prob. 22RQCh. 6 - Prob. 23RQCh. 6 - Prob. 24RQCh. 6 - Prob. 25RQCh. 6 - Prob. 26RQCh. 6 - Prob. 27RQCh. 6 - Prob. 28RQCh. 6 - Prob. 29RQCh. 6 - Prob. 30RQCh. 6 - Prob. 31RQCh. 6 - Prob. 32RQCh. 6 - Prob. 33RQCh. 6 - Prob. 1PCh. 6 - Prob. 2PCh. 6 - Prob. 3PCh. 6 - Prob. 4PCh. 6 - Design a PLC program and prepare a typical I/O...Ch. 6 - Prob. 6PCh. 6 - Prob. 7PCh. 6 - Prob. 8P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.Similar questions
- In TSSST switch (where SSS stands for a three-stage space-division switch) with N=150. It is used 15 time division switches in the first stage and 15 time division switches in the fifth stage. We use 3 crossbar switches in the second stage, 2 crossbars at the third stage, and 3 crossbars at the fourth stage. What is the total number of crosspoints?arrow_forward1- Write an Arduino program to make LED connected at pin(5) turn ON,when pressed on first switch and turn "OFF" after press second switch, the two switches are connected on pin(7) and pin(8) respectively,draw the circuit diagram.arrow_forwardCheck applicable statements that describes a typical network switch (L2 switch) and its usage:arrow_forward
- Draw a ladder diagram that will have the following results: a. Lamp L2 and Lamp L3 deactivated while Lamp L1 activated the moment power is turned ON. b. Lamp L1 and Lamp L3 deactivated while Lamp L2 activated when switch S2 is pressed and released. c. Lamp L1 and Lamp L2 deactivated while Lamp L3 activated when switch S3 is pressed and released. d. Lamp L2 and Lamp L3 deactivated while Lamp L1 activated when switch S1 is pressed and released.arrow_forwardQ2) Consider three-stage space-division switch with N=500, n= 50, k=5.4. What is the number of simultaneous connections if single-stage crossbar is to be used?arrow_forwardGround loops, or low-level circulating current, are commonly present when computer equipment is connected to multiple circuits supplied from different power sources and then those power sources are interconnected with shielded communication cables 1.true 2.falsearrow_forward
- Develop an algorithm in Arduino to repeatedly count the number of times a button has been pushed and released and show the count on the Arduino serial monitor. When the count reaches 13, turn on a LED and reset the count, to zero, on the next push and release of the button.arrow_forwardWhat is the main function of switcharrow_forwardCreate a program in SFC for the following: A three way switch where the left position operates “Indicator 1”, right position operates “Indicator 2” and the middle position where both the indicators are OFF.arrow_forward
- 50. The meaning of Straight-through Cable is a. Four wire pairs connect to the same pin on each end b. The cable Which Directly connects Computer to Computer c. Four wire pairs not twisted with each other d. The cable which is not twistedarrow_forwardComment on the following line: "Using a 7219 you can drive 64 LEDs while you only need 3 wires to interface it to a microcontroller"arrow_forwardExplain the functions of the switches (-T, -A, -v)arrow_forward
arrow_back_ios
arrow_forward_ios
Recommended textbooks for you
Systems ArchitectureComputer ScienceISBN:9781305080195Author:Stephen D. BurdPublisher:Cengage Learning
Systems Architecture
Computer Science
ISBN:9781305080195
Author:Stephen D. Burd
Publisher:Cengage Learning