![EBK GENERAL, ORGANIC, AND BIOLOGICAL CH](https://www.bartleby.com/isbn_cover_images/8220100853180/8220100853180_largeCoverImage.jpg)
(a)
Interpretation:
Between
Concept Introduction:
Boiling point:
Boiling is a form of evaporation where the conversion from the liquid state to vapor state occurs within the body of the liquid through bubble formation.
A normal boiling point is the temperature at which the liquid boils under a pressure of
London force:
London force is a type of weak intermolecular force that has an effect on boiling point. This weak temporary force occurs between two atoms or molecules (polar or non-polar)
The cause of London force is the temporary uneven distribution of electrons causing induced polarity. The strength of the London force depends on how easily a molecule can be distorted or polarized by the polarity present in another molecule. For the large molecules the outermost electrons are far from nucleus and as the result the attractive forces of nucleus acting on them are very weak and hence the outermost electrons can be easily polarized. Hence the induced polar molecule and the polar molecule will attract each other more.
Thus the molecules having higher mass have higher boiling point.
(b)
Interpretation:
Between
Concept Introduction:
Boiling point:
Boiling is a form of evaporation where the conversion from the liquid state to vapor state occurs within the body of the liquid through bubble formation.
A normal boiling point is the temperature at which the liquid boils under a pressure of
Hydrogen bonding:
Hydrogen bonding is an intermolecular force. This is an extra strong dipole-dipole interaction between a hydrogen atom covalently bonded to a small electronegative atom mainly
The vapor pressure of liquids having significant hydrogen bonding are much lower than those liquids having no hydrogen bonding. Because of presence of extensive hydrogen bonding the liquid molecules face difficulty to escape from the condensed state and additional energy is required to break the hydrogen bonds and go to the vapor state and as a result the liquids having extensive hydrogen bonding have higher boiling points.
Dipole-dipole interaction:
Dipole- dipole interactions are the strong intermolecular interaction that causes between two polar molecules.
In polar molecules there will be a force of attraction between the positive end and the negative end. Hence the molecules having higher electronegativity difference i.e. having more polarity will have higher dipole-dipole intermolecular attraction acting between them and as a result the boiling point will increase.
(c)
Interpretation:
Between
Concept Introduction:
Dipole-dipole interaction:
Dipole- dipole interactions are the strong intermolecular interaction that causes between two polar molecules.
In polar molecules there will be a force of attraction between the positive end and the negative end. Hence the molecules having higher electronegativity difference i.e. having more polarity will have higher dipole-dipole intermolecular attraction acting between them and as a result the boiling point will increase.
(d)
Interpretation:
Between
Concept Introduction:
Hydrogen bonding:
Hydrogen bonding is an intermolecular force. This is an extra strong dipole-dipole interaction between a hydrogen atom covalently bonded to a small electronegative atom mainly
The vapor pressure of liquids having significant hydrogen bonding are much lower than those liquids having no hydrogen bonding. Because of presence of extensive hydrogen bonding the liquid molecules face difficulty to escape from the condensed state and additional energy is required to break the hydrogen bonds and go to the vapor state and as a result the liquids having extensive hydrogen bonding have higher boiling points.
![Check Mark](/static/check-mark.png)
Want to see the full answer?
Check out a sample textbook solution![Blurred answer](/static/blurred-answer.jpg)
Chapter 7 Solutions
EBK GENERAL, ORGANIC, AND BIOLOGICAL CH
- What coefficient must be placed in the following blanks so that all atoms are accounted for in the products? C6H12O6 ------->___________C2H6O +_____________CO2 a. 1;2 b. 3;1 c. 1;3 d. 2;2arrow_forwardWhen copper and sulfur react, two products are possible: copper(I) sulfide, Cu2S, and copper(II) sulfide, CuS. A scientist hypothesizes that holding a loop of thin copper wire in the vapour from boiling sulfur will produce pure Cu2S when the copper and sulfur react. Suggest what measurements, related to mole ratios, the scientist should make to test this hypothesis.arrow_forwardAt 39.9ºC, a solution of ethanol (XetOH = 0.9006, P * etOH = 130.4 Torr) and isooctane (P * iso = 43.9 Torr) forms a vapor phase with YetOH = 0.6667. The total pressure is 185.9 a. Calculate the activity and the activity coefficient of each component.b. Calculate the total pressure the solution would have if it were ideal.c. Comparing the ideal pressure to the actual pressure, what does this indicate about the molecular interactions?arrow_forward
- Bubbles of CO2 are formed during the reaction between vinegar, water and Alka Seltzer. Provide an argument for why the CO2 molecules do not remain in the solution.arrow_forwardWhich of the following is an organic molecule?a. CO2 c. H2Ob. O2 d. C6H12O6arrow_forwardWhich of the following compounds would be most soluble in carbon tetrachloride, CCl4? a. NH3 d. CH3OHb. H2O e. C6H6c. HClarrow_forward
- What coefficients must be placed in the following blanks so that all atoms are accounted for in the products?C6H12O6 → ________ C2H6O + ________ CO2 Group of answer choices A. 2; 1 B. 3; 1 C. 1; 3 D. 2; 2arrow_forwardHow many liters of dry hydrogen gas, measured at 798 mmHg and 21C, will be released by the decomposition of 230 mL of H20 at 1.42atm and 30C? 2 H20 (g) → 2 H2 (g) + O2 (g) Answer to 3 decimal places. Your Answer: Answer unitsarrow_forwardCao (s) (calcium oxide) is the main ingredient of concrete. While mixing Cao with water, the mixture gets hotter rapidly by its own. The chemical equation of the reaction is given below. Cao (s) + H20 (liq) > Ca(OH)2 (s) Based on the above information, which of the following is correct for the above process to mix Cao (s) with water. O a. AH> 0, AS> 0, AG0, AG 0 , ΔS> 0 , ΔG>0 O e. AH0, AG>0 O f. AH 0arrow_forward