Concept explainers
The Manning equation can be written for a rectangular open channel as
where
Want to see the full answer?
Check out a sample textbook solutionChapter 8 Solutions
Package: Numerical Methods For Engineers With 2 Semester Connect Access Card
Additional Math Textbook Solutions
Fundamentals of Differential Equations (9th Edition)
Advanced Engineering Mathematics
Basic Technical Mathematics
Algebra And Trigonometry (11th Edition)
Developmental Mathematics (9th Edition)
- If the flow depth remains constant in an open-channel flow, the flow is called(a) Uniform flow (b) Steady flow (c) Varied flow (d) Unsteady flow (e) Laminar flowarrow_forwardQ1/ Neglecting losses, determine the discharge in Fig. below Oil sp gr 0.75 3 ft 4 ft 4 in, diam Waterarrow_forwardQ1/ Neglecting losses, determine the discharge in Fig. below Oil sp gr 0.75 3 ft 4 in, diam Waterarrow_forward
- 2.Water flows through a rectangular channel with a width b = 2 m and a height (Pw) = 1 m, the flow rate ranges from Qmin = 0.02 m^3/s and Qmax = 0.60 m^3/s. This flow rate is measured using Rectangular sharp-crested weir Triangular sharp-crested with = 90^o Broad-crested weir Plot onto the graph Q = Q(H) for each type of weir and give your analysis which type of weir is most appropriate to applyarrow_forwardA channel step, shown in the figure below, is in a 12 m wide channel with discharge, Q, of 46 m3/s. The flow depth at section 1 is 1.6 m and the step height is 0.4 m. The bed of the channel, upstream and downstream of the step, is horizontal and smooth. Part A. Sketch on the figure the variation of the pressure with depth at sections 1 and 2, and on the verticalface of the step. Sections 1 and 2 are located far enough from the step for the velocity to be essentially horizontal and uniform. Part B. Draw the control volume contained between sections 1 and 2 and show on the figure the forces acting on it. Show also your choice for the positive direction of distance and of force. Part C. Write the momentum equation as applied to the control volume between sections 1 and 2, using the sign convention you have chosen. Show the forces and velocities used in the momentum equation. Part D. Compute the following quantities: (a) Velocity of flow at section 1. (b) Specific energy at section 1. (c)…arrow_forwardIn flowing from section (1) to section (2) along a rectangular open channel, the water depth decreases by a factor of three and the Froude number changes from a subcritical value of 0.7 to a supercritical value of 3.4. Determine the channel width at (2) if it is 8 ft. wide at section (1). Assume stead-state flow.arrow_forward
- Given a straight channel with a rectangular cross section, width = 200 μm, height = 120 µm, if the volumetric flow rate is 0.1 mL/min, and dynamic viscosity of the water is 1 CP. would it be a laminar flow? Under the same pressure gradient (), if we change to a circular cross section, what would be the diameter of the channel if we would like to maintain the same volumetric flow rate?arrow_forwardConsider a rectangular channel 3 m wide laid on a 1°slope. If the water depth is 2 m, the hydraulic radius is(a) 0.43 m, (b) 0.6 m, (c) 0.86 m, (d ) 1.0 m, (e) 1.2 marrow_forwardThe equilateral-triangle channel in Fig. has constantslope So and constant Manning factor n. If y= a/2,fi nd an analytic expression for the fl ow rate Q.arrow_forward
- Water flows in an open channel across a weir which occupies the full width of the channel. The lenght of the weir is 0.5 m and the height of water over the weir is 100 mm. What is the flow rate of water?arrow_forwardWater flows in a rectangular open channel of width 0.6 m at a rate of 0.25 m3/s. If the flow depth is 0.2 m, what is the alternate flow depth if the character of flow were to change? (a) 0.2 m (b) 0.26 m (c) 0.35 m (d) 0.6 m (e) 0.8 marrow_forwardConsider uniform flow through an open channel lined with bricks with a Manning coefficient of n = 0.015. If the Manning coefficient doubles (n = 0.030) as a result of some algae growth on surfaces while the flow cross section remains constant, the flow rate will (a) double, (b) decrease by a factor of √2, (c) remain unchanged, (d) decrease by half, or (e) decrease by a factor of 21/3.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY