Steel Design (Activate Learning with these NEW titles from Engineering!)
6th Edition
ISBN: 9781337094740
Author: Segui, William T.
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Question
Chapter 8, Problem 8.4.14P
To determine
(a)
The required size of weld on the basis of elastic analysis from Allowed Stress Design.
To determine
(b)
The required size of weld on the basis of ultimate strength method.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Compression member.
Compute:
- Ix̄
- Centroidal y axis
- kL/ry
- rx
- design compressive strength
- allowable compressive strength
Channel sections are used as a purlin. The top chords of the truss are sloped at 6H to 1V. Trusses are spaced 4m on centers. Use the properties of the channel section in the picture.
Loads:
Dead load = 600 Pa
Live load = 800 Pa
Wind load = 1,300Pa
Wind coefficients:
Windward = 0.25
Leeward = -0.4
Use Fbx=Fby=248 MPa. Determine the safe spacing of purlins (Use load combination of 0.75(D+L+W)
Chapter 8 Solutions
Steel Design (Activate Learning with these NEW titles from Engineering!)
Ch. 8 - Prob. 8.2.1PCh. 8 - Prob. 8.2.2PCh. 8 - A plate is used as a bracket and is attached to a...Ch. 8 - Prob. 8.2.4PCh. 8 - Prob. 8.2.5PCh. 8 - Prob. 8.2.6PCh. 8 - Prob. 8.2.7PCh. 8 - Prob. 8.2.8PCh. 8 - Prob. 8.2.9PCh. 8 - Prob. 8.2.10P
Ch. 8 - Prob. 8.2.11PCh. 8 - Prob. 8.2.12PCh. 8 - Prob. 8.2.13PCh. 8 - Prob. 8.3.1PCh. 8 - Prob. 8.3.2PCh. 8 - Prob. 8.3.3PCh. 8 - Prob. 8.3.4PCh. 8 - Prob. 8.3.5PCh. 8 - Prob. 8.3.6PCh. 8 - Prob. 8.3.7PCh. 8 - Prob. 8.3.8PCh. 8 - Prob. 8.3.9PCh. 8 - Prob. 8.3.10PCh. 8 - Use an elastic analysis and determine the maximum...Ch. 8 - Use an elastic analysis and determine the maximum...Ch. 8 - Use an elastic analysis and determine the maximum...Ch. 8 - Prob. 8.4.4PCh. 8 - Prob. 8.4.5PCh. 8 - Prob. 8.4.6PCh. 8 - Use an elastic analysis and compute the extra load...Ch. 8 - Use an elastic analysis and compute the extra load...Ch. 8 - Prob. 8.4.9PCh. 8 - Prob. 8.4.10PCh. 8 - Prob. 8.4.11PCh. 8 - Prob. 8.4.12PCh. 8 - Prob. 8.4.13PCh. 8 - Prob. 8.4.14PCh. 8 - Prob. 8.4.15PCh. 8 - Prob. 8.4.16PCh. 8 - Prob. 8.4.17PCh. 8 - Prob. 8.4.18PCh. 8 - a. Use LRFD and design a welded connection for the...Ch. 8 - Prob. 8.4.20PCh. 8 - Prob. 8.5.1PCh. 8 - Prob. 8.5.2PCh. 8 - Prob. 8.5.3PCh. 8 - Prob. 8.5.4PCh. 8 - Prob. 8.5.5PCh. 8 - Prob. 8.6.1PCh. 8 - Prob. 8.6.2PCh. 8 - Prob. 8.6.3PCh. 8 - Prob. 8.6.4PCh. 8 - Prob. 8.7.1PCh. 8 - Prob. 8.7.2PCh. 8 - Prob. 8.7.3PCh. 8 - Prob. 8.8.1PCh. 8 - Prob. 8.8.2PCh. 8 - Prob. 8.8.3PCh. 8 - Prob. 8.8.4P
Knowledge Booster
Similar questions
- The given beam is laterally supported at the ends and at the 1 3 points (points 1, 2, 3, and 4). The concentrated load is a service live load. Use Fy=50 ksi and select a W-shape. Do not check deflections. a. Use LRFD. b. Use ASD.arrow_forwardUse A992 steel and select the lightest W shape. Use any design procedure.a. Use LRFD.b. Use ASD.arrow_forwardA L 3 x 2 x ¼ is connected to a gusset plate via six bolts. The nominal diameter of the bolt is 0.25 inches, the pitch spacing is 1.75 inches, the gage spacing is 2 inches, and the thickness of the connection is (¼) inch. The yield stress is 50 Ksi and the ultimate stress is 60 Ksi. Consider section line (a-a') for the analysis. . a. What is the effective net area (Ae) of the angle section in inches2 [a-a']?(The shear lag factor is "0.80") b. What is the design tensile yielding strength in Kips for the steel member? c. What is the design tensile rupture strength in Kips for the steel member? d. What is the minimum Factor of Safety if a tensile load of 23 Kips is applied to the angle section? please make sure the answer is correct 100% I only need the final answersarrow_forward
- Compression membersarrow_forwardGive an correct answer with proper method or i will give an dislike A cantilever beam of effective depth 315 mm has span of 2.5 m. The percentage of tensile reinforcement is 1.5% Fe-250 bars. Check the beam for its depth for deflection only. Take M20 conerete.arrow_forwardUse AISC Equation E3-2 or E3-3. Compute both the design strength for LRFD and the allowable strength for ASD.arrow_forward
- Channel sections are used as a purlin. The top chords of the truss are sloped at 5H to 2V. Trusses are spaced 5m on centers and the purlins are spaced 1.4m on centers. Use the properties of the channel section BELOW. Loads: (Consider all loads pass thru the centroid of the section.) Dead load = 750 Pa Live load = 1,000 Pa Wind load = 1,400Pa Wind coefficients: Windward = 0.3 Leeward = -0.5 Use Fbx=Fby=250 MPa. Determine the maximum value of the interaction equation using the load combination of 0.75(D+L+W)arrow_forwardA 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with 7/8-in diameter bolts as shown in the figure. Use s = 2.0 and g = 3.0. Determine the design tensile strength of the section based on tensile rupture of the net area. Determine the allowable tensile strength of the section based on yielding of the gross area.arrow_forwardTHE TENSION MEMBERS IS COMPOSED OF A 200x150x10 mm THICK ANGLE CONNECTED USING 21 mmo RIVETS AS ASHOWN. Ag = 3400 mm , x = 25 mm, Fy = 250 MPA AND Fu = 400 MPA. USE ALLOWABLE STRENGTH DESIGN (ASD). DETERMINE THE FOLLLOWING : THE NET AREA OF THE SECTION. THE TENSILE CAPACITY OF THE MEMBER BASED ON YIELDING OF Ag. THE TENSILE CAPACITY OF THE MEMBER BASED ON FRACTURE OF Anarrow_forward
- 1.Use LRFD and design the tension members of the roof truss shown in Figure below. Use double-angle shapes throughout and assume 10-mm-thick gusset plates and welded connections. Assume a shear lag factor of U = 0.80. The trusses are spaced at 9 meters. Use A36 steel and design forthe following loads.Metal deck : 190 Pa of roof surfaceBuilt-up roof : 575 Pa of roof surfacePurlins : 145 Pa of roof surface (estimated)Roof Live Load : 960 Pa of horizontal projectionTruss weight : 240 Pa of horizontal projection (estimated) 2. Use A36 steel and design sag rods for the truss of Problem 1. Assume that, once attached, the metal deck will provide lateral support for the purlins; therefore, the sag rods need to be designed for the purlin weight only.a. Use LRFD.b. Use ASD.arrow_forwardTENSION MEMBERS: THE SINGLE 200 X 10 mm STEEL PLATE IS CONNECTED TO A 12 mm THICK STEEL PLATE BY FOUR 16 mm DIAMETER RIVETS AS SHOWN IN THE FIGURE. THE RIVETS USED ARE A502 GRADE 2, HOT DRIVEN RIVETS. THE STEEL IS ASTM A36 WITH Fy = 248 MPa AND Fu = 400 MPa. DETERMINE THE VALUE OF P. a. P BASED ON TENSION OF GROSS AREA b. P BASED ON TENSION OF NET AREA c. P BASED ON BEARING OF PROJECTED AREA d. P BASED ON SHEAR RUPTURE (BLOCK SHEAR)arrow_forward
arrow_back_ios
arrow_forward_ios
Recommended textbooks for you
Steel Design (Activate Learning with these NEW ti...Civil EngineeringISBN:9781337094740Author:Segui, William T.Publisher:Cengage Learning
Steel Design (Activate Learning with these NEW ti...
Civil Engineering
ISBN:9781337094740
Author:Segui, William T.
Publisher:Cengage Learning