EBK STATISTICS FOR ENGINEERS AND SCIENT
4th Edition
ISBN: 9780100274389
Author: Navidi
Publisher: YUZU
expand_more
expand_more
format_list_bulleted
Question
Chapter 9, Problem 22SE
To determine
Check whether the there is any difference in salinity among the areas.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Fluid inclusions are microscopic volumes of fluid that are trapped in rock during rock
formation. The article "Fluid Inclusion Study of Metamorphic Gold-Quartz Veins in
Northwestern Nevada, U.S.A.: Characteristics of Tectonically Induced Fluid" (S. Cheong,
Geosciences Journal, 2002:103-115) describes the geochemical properties of fluid
inclusions in several different veins in northwest Nevada. The following table presents data
on the maximum salinity (% NaCi by weight) of inclusions in several rock samples from
several areas.
Salinity
Area
Humboldt Range
Santa Rosa Range
9.2 10.0 11.2 8.8
5.2
6.1
8.3
Ten Mile
7.9
6.7 9.5 7.3 10.4 7.0
Antelope Range
Pine Forest Range
6.7
8.4 9.9
10.5 16.7 17.5 15.3 20.0
Can you conclude that the salinity differs among the areas?
The article "Experimental Measurement of Radiative Heat Transfer in Gas-Solid
Suspension Flow System" (G. Han, K. Tuzla, and J. Chen, AIChe Journal, 2002:1910-
1916) discusses the calibration of a radiometer. Several measurements were made on the
electromotive force readings of the radiometer (in volts) and the radiation flux (in kilowatts
per square meter). The results (read from a graph) are presented in the following table.
Heat flux (y)
15 31 51 55 67 89
Signal output (x) 1.08 2.42 4.17 4.46 5.17 6.92
Compute the least-squares line for predicting heat flux from the signal output.
If the radiometer reads 3.00 V, predict the heat flux.
If the radiometer reads 8.00 V, should the heat flux be predicted? If so, predict it. If
not, explain why.
C.
The article "Modeling Resilient Modulus and Temperature Correction for Saudi Roads" (H.
Wahhab, I. Asi, and R. Ramadhan, Journal of Materials in Civil Engineering, 2001:298–
305) describes a study designed to predict the resilient modulus of pavement from physical
properties. The following table presents data for the resilient modulus at 40°Cin10® kPa (y),
the surface area of the aggregate in m²/kg (x1), and the softening point of the asphalt in °C
(х).
y
X1
X2
1.48
5.77
60.5
1.70
7.45
74.2
2.03
8.14
67.6
2.86
8.73
70.0
2.43
7.12
64.6
3.06
6.89
65.3
2.44
8.64
66.2
1.29
6.58
64.1
3.53
9.10
68.6
1.04
8.06
58.8
1.88
5.93
63.2
1.90
8.17
62.1
1.76
9.84
68.9
2.82
7.17
72.2
1.00
7.78
54.1
The full quadratic model is y = + P,x, + PzX, + Pz*jXz + Pxx¡ + Bzx; + €. Which
submodel of this full model do you believe is most appropriate? Justify your answer by
fitting two or more models and comparing the results.
Chapter 9 Solutions
EBK STATISTICS FOR ENGINEERS AND SCIENT
Ch. 9.1 - A study is made of the effect of curing...Ch. 9.1 - The article Nutrient Deprivation Improves Field...Ch. 9.1 - Prob. 3ECh. 9.1 - The antibiotic gentamicin sulphate is often...Ch. 9.1 - The article influence of Age on Masonry Bond...Ch. 9.1 - Archaeologists can determine the diets of ancient...Ch. 9.1 - The article Secretion of Parathyroid Hormone...Ch. 9.1 - The article Impact of Free Calcium Oxide Content...Ch. 9.1 - A certain chemical reaction was run three times at...Ch. 9.1 - An experiment to compare the lifetimes of four...
Ch. 9.1 - Prob. 11ECh. 9.1 - Prob. 12ECh. 9.1 - Prob. 13ECh. 9.1 - Prob. 14ECh. 9.1 - Refer to Exercise 12. a. Compute the quantity...Ch. 9.1 - Prob. 16ECh. 9.1 - Prob. 17ECh. 9.1 - Prob. 18ECh. 9.1 - Prob. 19ECh. 9.1 - The following MINITAB output presents a power...Ch. 9.2 - Exercises for Section 9.2 1.The article Organic...Ch. 9.2 - The article Optimum Design of an A-pillar Trim...Ch. 9.2 - Prob. 3ECh. 9.2 - Refer to Exercise 2 in Section 9.1. a.Use the...Ch. 9.2 - Refer to Exercise 13 in Section 9.1. a. Use the...Ch. 9.2 - Refer to Exercise 1 in Section 9.1. A scientist...Ch. 9.2 - Refer to Exercise 13 in Section 9.1. A...Ch. 9.2 - Refer to Exercise 3 in Section 9.1. a. Use the...Ch. 9.2 - Refer to Exercise 5 in Section 9.1. a. Use the...Ch. 9.2 - Refer to Exercise 9 in Section 9.1. a. Use the...Ch. 9.2 - Refer to Exercise 16 in Section 9.1. a. Use the...Ch. 9.2 - Refer to Exercise 18 in Section 9.1. a. Use the...Ch. 9.2 - In an experiment to determine the effect of...Ch. 9.2 - In an experiment to determine the effect of curing...Ch. 9.2 - Prob. 15ECh. 9.2 - For some data sets, the F statistic will reject...Ch. 9.3 - To assess the effect of piston ring type and oil...Ch. 9.3 - A machine shop has three machines used in...Ch. 9.3 - An experiment to determine the effect of mold...Ch. 9.3 - The effect of curing pressure on bond strength was...Ch. 9.3 - The article Change in Creep Behavior of Plexiform...Ch. 9.3 - Prob. 6ECh. 9.3 - Prob. 7ECh. 9.3 - Adding glass panicles to clay brick may improve...Ch. 9.3 - The article Application of Radial Basis Function...Ch. 9.3 - Prob. 10ECh. 9.3 - Prob. 11ECh. 9.3 - The article Anodic Fenton Treatment of Treflan MTF...Ch. 9.3 - Refer to Exercise 12. The treatments with a...Ch. 9.3 - The article Use of Taguchi Methods and Multiple...Ch. 9.3 - The article T-Bracing for Stability of Compression...Ch. 9.3 - The article referred to in Exercise 15 also...Ch. 9.3 - Prob. 17ECh. 9.3 - Prob. 18ECh. 9.3 - The article Cellulose Acetate Microspheres...Ch. 9.4 - Recycling newsprint is important in reducing...Ch. 9.4 - A study was done to see which of four machines is...Ch. 9.4 - Prob. 3ECh. 9.4 - Three different corrosion-resistant coatings are...Ch. 9.4 - The article Genotype-Environment Interactions and...Ch. 9.4 - The article Sprinkler Technologies, Soil...Ch. 9.4 - The article Bromate Surveys in French Drinking...Ch. 9.4 - The article Multi-objective Scheduling Problems:...Ch. 9.4 - You have been given the task of designing a study...Ch. 9.4 - An engineering professor wants to determine which...Ch. 9.5 - Prob. 1ECh. 9.5 - Give an example of a factorial experiment in which...Ch. 9.5 - Prob. 3ECh. 9.5 - The article Efficient Pyruvate Production by a...Ch. 9.5 - The article cited in Exercise 4 also investigated...Ch. 9.5 - A metal casting process for the production of...Ch. 9.5 - The article An Investigation into the Ball...Ch. 9.5 - In a 2p design with one replicate per treatment,...Ch. 9.5 - Prob. 9ECh. 9.5 - Prob. 10ECh. 9.5 - The article Factorial Design for Column Rotation...Ch. 9.5 - Prob. 12ECh. 9.5 - Prob. 13ECh. 9 - The article Gypsum Effect on the Aggregate Size...Ch. 9 - Prob. 2SECh. 9 - Prob. 3SECh. 9 - Prob. 4SECh. 9 - Prob. 5SECh. 9 - Prob. 6SECh. 9 - Prob. 7SECh. 9 - The article Case Study Based Instruction of DOE...Ch. 9 - The article Combined Analysis of Real-Time...Ch. 9 - Vermont maple sugar producers sponsored a testing...Ch. 9 - Prob. 11SECh. 9 - Prob. 12SECh. 9 - Prob. 13SECh. 9 - The article Enthalpies and Entropies of Transfer...Ch. 9 - Prob. 15SECh. 9 - Prob. 16SECh. 9 - The article Factorial Experiments in the...Ch. 9 - The Williamsburg Bridge is a suspension bridge...Ch. 9 - Prob. 19SECh. 9 - In the article Nitrate Contamination of Alluvial...Ch. 9 - The article Factorial Experiments in the...Ch. 9 - Prob. 22SECh. 9 - Prob. 23SECh. 9 - Prob. 24SE
Knowledge Booster
Similar questions
- The article "Characteristics and Trends of River Discharge into Hudson, James, and Ungava Bays, 1964-2000" (S. Dery, M. Stieglitz, et al., Journal of Climate, 2005:2540-2557) presents measurements of discharge rate x (in kmlyr) andpeakflow y (in m/s) for 42 rivers that drain into the Hudson, James, and Ungava Bays. The data are shown in the following table: Discharge Peak Flow 94.24 4110.3 66.57 4961.7 59.79 10275.5 48.52 6616.9 40.00 7459.5 32.30 2784.4 31.20 3266.7 30.69 4368.7 26.65 1328.5 22.75 4437.6 21.20 1983.0 20.57 1320.1 19.77 1735.7 18.62 1944.1 17.96 3420.2 17.84 2655.3 16.06 3470.3 1561.6 14.69 11.63 869.8 11.19 936.8 11.08 1315.7 10.92 1727.1 9.94 768.1 7.86 483.3arrow_forwardThe article “Wastewater Treatment Sludge as a Raw Material for the Production of Bacillus thuringiensis Based Biopesticides” (M. Tirado Montiel, R. Tyagi, and J. Valero, Water Research, 2001:3807–3816) presents measurements of total solids, in g/L, for seven sludge specimens. The results (rounded to the nearest gram) are 20, 5, 25, 43, 24, 21, and 32. Assume the distribution of total solids is approximately symmetric. a) Can you conclude that the mean concentration of total solids is greater than 14 g/L? Compute the appropriate test statistic and find the P-value. b) Can you conclude that the mean concentration of total solids is less than 30 g/L? Compute the appropriate test statistic and find the P-value. c) An environmental engineer claims that the mean concentration of total solids is equal to 18 g/L. Can you conclude that the claim is false?arrow_forwardAn article in the ASCE Journal of Energy Engineering [“Overview of Reservoir Release Improvements at 20 TVA Dams” (Vol. 125, April 1999, pp. 1–17)] presents data on dissolved oxygen concentrations in streams below 20 dams in the Tennessee Valley Authority system. The observations are (in milligrams per liter):arrow_forward
- The article "Effect of Granular Subbase Thickness on Airfield Pavement Structural Response" (K. Gopalakrishnan and M. Thompson, Journal of Materials in Civil Engineering, 2008:331-342) presents a study of the amount of surface deflection caused by aircraft landing on an airport runway. A load of 160 kN was applied to a runway surface, and the amount of deflection in mm (y) was measured at various distances in m (x) from the point of application. The results are presented in the following table. y 0.000 3.24 0.305 2.36 0.610 1.42 0.914 0.87 1.219 0.54 1.524 0.34 1.830 0.24 a. Fit the linear model y = Bo + B1x + ɛ. For each coefficient, test the hypothesis that the coefficient is equal to 0. b. Fit the quadratic model y = Bo + Bịx + B2x² + ɛ. For each coefficient, test the hypothesis that the coefficient is equal to 0. %3D Fit the cubic model y = Bo + B1x + B2x? + B3x + E. For each coefficient, test the C. hypothesis that the coefficient is equal to 0. d. Which of the models in parts (a)…arrow_forwardThe depth of wetting of a soil is the depth to which water content will increase owing to extemal factors. The article "Discussion of Method for Evaluation of Depth of Wetting in Residential Areas" (J. Nelson, K. Chao, and D. Overton, Journal of Geotechnical and Geoenvironmental Engineering, 2011:293-296) discusses the relationship between depth of wetting beneath a structure and the age of the structure. The article presents measurements of depth of wetting, in meters, and the ages, in years, of 21 houses, as shown in the following table. Age Depth 7.6 4 4.6 6.1 9.1 3 4.3 7.3 5.2 10.4 15.5 5.8 10.7 4 5.5 6.1 10.7 10.4 4.6 7.0 6.1 14 16.8 10 9.1 8.8 Compute the least-squares line for predicting depth of wetting (y) from age (x). b. Identify a point with an unusually large x-value. Compute the least-squares line that results from deletion of this point. Identify another point which can be classified as an outlier. Compute the least-squares line that results from deletion of the outlier,…arrow_forwardThe article "Polyhedral Distortions in Tourmaline" (A. Eril, J. Hughes, et al., The Canadian Mineralogist, 2002 153-162) presents a model for calculating bond-length distortion in vanadium-bearing tourmaline. To check the accuracy of the model, several calculated values (x) were compared with directly observed values (y) The results (read from a graph) are presented in the following table. Observed Value Calculated Value 0.33 0.36 0.36 0.36 0.54 0.58 0.56 0.66 0.64 0.64 0.66 0.67 0.74 0.58 0.74 0.78 0.79 0.86 0.97 0.97 1.11 1.03 110 1.06 1.13 1.08 114 117 Assume that the observed value y is an unbiased measurement of the true value. Show that if the calculated value x is accurate (ie., equal to the true value), then y = x+ , where e is measurement error. a. b. Compute the least-squares line y= Show that if the calculated value is accurate, then the true coefficients are , = Oand e, Â, + Â,x- C. =1. d. Test the null hypotheses e,-0 and e, = 1. Is it plausible that the calculated value…arrow_forward
- The article "Oxidation State and Activities of Chromium Oxides in Cao-SiO,-CrO, Slag System" (Y. Xiao, L. Holappa, and M. Reuter, Metallurgical and Materials Transactions B, 2002:595-603) presents the amount x (in mole percent) and activity coefficient y of CrO,5 for several specimens. The data, extracted from a larger table, are presented in the following table. х У 2.6 10.20 5.03 19.9 8.84 0.8 6.62 5.3 2.89 20.3 2.31 39.4 7.13 5.8 3.40 29.4 5.57 2.2 7.23 5.5 2.12 33.1 1.67 44.2 5.33 13.1 16.70 0.6 9.75 2.2 2.74 16.9 2.58 35.5 1.50 48.0 Compute the least-squares line for predicting y from x. b. Plot the residuals versus the fitted values. Compute the least-squares line for predicting y from 1/x. d. Plot the residuals versus the fitted values. C. Using the better fitting line, find a 95% confidence interval for the mean value of y when x= 5.0.arrow_forwardThe article “‘Little Ice Age’ Proxy Glacier Mall Balance Records Reconstructed from Tree Rings in the Mt. Waddington Area, British Columbia Coast Mountains, Canada” (S. Larocque and D. Smith, The Holocene, 2005:748–757) evaluates the use of tree ring widths to estimate changes in the masses of glaciers. For the Sentinel glacier, the net mass balance (change in mass between the end of one summer and the end of the next summer) was measured for 23 years. During the same time period, the tree ring index for white bark pine trees was measured, and the sample correlation between net mass balance and tree ring index was r = −0.509. Can you conclude that the population correlation ρ differs from 0?arrow_forwardThe article "Effect of Microstructure and Weathering on the Strength Anisotropy of Porous Rhyolite" (Y. Matsukura, K. Hashizume, and C. Oguchi, Engineering Geology, 2002:39- 17) investigates the relationship between the angle betwween cleavage and flow structure and the strength of porous rhyolite. Strengths (in MPa) were measured for a mumber of specimens cut at various angles. The mean and standard deviation of the strengths for each angle are presented in the following table. Angle Mean 0° 22.9 Sample Size Standard Deviation 2.98 12 15° 22.9 1.16 30° 19.7 3.00 45° 14.9 2.99 60° 13.5 2.33 75° 11.9 2.10 90 14.3 3.95 6. Can you conclude that strength varies with the angle?arrow_forward
- Q3) An experiment was carried out to investigate variation of solubility of chemical X in water. The quantities in kg that dissolved in 1 liter at various temperatures are show in the table (1). Table (1) Temperature C Mass of X 2.1 2.6 2.9 3.3 15 20 25 30 35 4 50 5.1 70 7 Use the proper methods to answer the following questions: a) Draw a scatter diagram to show the data. b) Estimate the temperature based on the mass of X. c) What quantity might be expected to dissolve at 42 C? Find the quantity that your cquation indicates would dissolve at 10 C and comment on your answer.arrow_forwardIn Applied Life Data Analysis (Wiley, 1982), Wayne Nelson presents the breakdown time of an insulating fluid between electrodes at 34kV. The times, in minutes, are as follows: 0.20, 0.71, 0.92, 1.32, 2.67, 3.32, 4.15, 4.61, 4.83, 6.49, 7.41, 8.03, 8.31, 12.77, 31.53, 32.56, 33.80, 36.41, and 72.32. Calculate the sample mean and sample deviation of the breakdown data. Round your answers to 2 decimal places. The sample mean is Blank 1. The sample standard deviation is Blank 2 Blank 1 Add your answer Blank 2 Add your answerarrow_forwardThe article "Two Different Approaches for RDC Modelling When Simulating a Solvent Deasphalting Plant" (J. Aparicio, M. Heronimo, et al., Computers and Chemical Engineering, 2002:1369–1377) reports flow rate (in dmh) and specific gravity measurements for a sample of paraffinic hydrocarbons. The natural logs of the flow rates (y) and the specific gravity measurements (x) are presented in the following table. х -1.204 0.8139 -0.580 0.8171 0.049 0.8202 0 673 0.8233 1.311 0.8264 1.959 0.8294 2.614 0.8323 3.270 0.8352 Fit the linear model y = Bo + B,x + ɛ. For each coefficient, test the hypothesis that the coefficient is equal to 0. Fit the quadratic model y = Bo + B,x + B2x? + E. For each coefficient, test the a. b. hypothesis that the coefficient is equal to 0. Fit the cubic model y = Bo + Bix + B2x² + Bax + E. For each coefficient, test the C. hypothesis that the coefficient is equal to 0. Which of the models in parts (a) through (c) is the most appropriate? Explain. Using the most…arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
MATLAB: An Introduction with ApplicationsStatisticsISBN:9781119256830Author:Amos GilatPublisher:John Wiley & Sons Inc
Probability and Statistics for Engineering and th...StatisticsISBN:9781305251809Author:Jay L. DevorePublisher:Cengage Learning
Statistics for The Behavioral Sciences (MindTap C...StatisticsISBN:9781305504912Author:Frederick J Gravetter, Larry B. WallnauPublisher:Cengage Learning
Elementary Statistics: Picturing the World (7th E...StatisticsISBN:9780134683416Author:Ron Larson, Betsy FarberPublisher:PEARSON
The Basic Practice of StatisticsStatisticsISBN:9781319042578Author:David S. Moore, William I. Notz, Michael A. FlignerPublisher:W. H. Freeman
Introduction to the Practice of StatisticsStatisticsISBN:9781319013387Author:David S. Moore, George P. McCabe, Bruce A. CraigPublisher:W. H. Freeman
MATLAB: An Introduction with Applications
Statistics
ISBN:9781119256830
Author:Amos Gilat
Publisher:John Wiley & Sons Inc
Probability and Statistics for Engineering and th...
Statistics
ISBN:9781305251809
Author:Jay L. Devore
Publisher:Cengage Learning
Statistics for The Behavioral Sciences (MindTap C...
Statistics
ISBN:9781305504912
Author:Frederick J Gravetter, Larry B. Wallnau
Publisher:Cengage Learning
Elementary Statistics: Picturing the World (7th E...
Statistics
ISBN:9780134683416
Author:Ron Larson, Betsy Farber
Publisher:PEARSON
The Basic Practice of Statistics
Statistics
ISBN:9781319042578
Author:David S. Moore, William I. Notz, Michael A. Fligner
Publisher:W. H. Freeman
Introduction to the Practice of Statistics
Statistics
ISBN:9781319013387
Author:David S. Moore, George P. McCabe, Bruce A. Craig
Publisher:W. H. Freeman