![Fox And Mcdonald's Introduction To Fluid Mechanics](https://www.bartleby.com/isbn_cover_images/9781118921876/9781118921876_largeCoverImage.gif)
Fox And Mcdonald's Introduction To Fluid Mechanics
9th Edition
ISBN: 9781118921876
Author: Pritchard, Philip J.; Leylegian, John C.; Bhaskaran, Rajesh
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 9, Problem 23P
Using numerical results obtained by Blasius (Table 9.1, on the web), evaluate the distribution of shear stress in a laminar boundary layer on a flat plate. Plot τ/τw versus y/δ. Compare with results derived from the approximate parabolic velocity profile given in Problem 9.8.
Expert Solution & Answer
![Check Mark](/static/check-mark.png)
Trending nowThis is a popular solution!
![Blurred answer](/static/blurred-answer.jpg)
Students have asked these similar questions
V 13 u
. The velocity profile for boundary layer over a
3 y
1
13
y
Ux
flat plate is given by,
u.
2 8x
2 8x
280 Vx
where, 8x =
13 u
(a) Develop the expression for friction
coefficient.
(b) Find the expression for average drag
coefficient over length L.
plate 450 mm x 150 mm has been placed longitudinally in a stream of crude oil (specific gravity 0.925 and kinematic viscosity of 9.0 x 10-5 m2/s) which flows with velocity of 6 m/s. Calculate: (i) the friction drag on the plate; (ii) the thickness of the boundary layer at a distance 215 mm from the trailing edge;(iii) the thickness of the boundary layer at the trailing edge; (iv) shear stress at the trailing edge.
6- A uniform free stream of air at 0.8 m/s flows over a flat plate (4 m long x 1 m wide).
Assuming the boundary layer to be laminar on the plate and the velocity profile is:
Find the ratio of the drag force on the front half portion to the drag
U.
2
force on the rear half portion of the plate. (p = 1.2 kg/m; v = 1.51x10 m²/s)
[2.42]
Chapter 9 Solutions
Fox And Mcdonald's Introduction To Fluid Mechanics
Ch. 9 - The roof of a minivan is approximated as a...Ch. 9 - A model of a river towboat is to be tested at 1:18...Ch. 9 - For flow over a smooth plate, what approximately...Ch. 9 - A model of a thin streamlined body is placed in a...Ch. 9 - A student is to design an experiment involving...Ch. 9 - A 1 m 2 m sheet of plywood is attached to the...Ch. 9 - The extent of the laminar boundary layer on the...Ch. 9 - Velocity profiles in laminar boundary layers often...Ch. 9 - An approximation for the velocity profile in a...Ch. 9 - Evaluate / for each of the laminar boundary-layer...
Ch. 9 - Evaluate the displacement thickness and the...Ch. 9 - Evaluate the displacement thickness and the...Ch. 9 - A fluid, with density = 1.5 slug/ft3, flows at U...Ch. 9 - Solve Problem 9.13 with the velocity profile at...Ch. 9 - Air flows in a horizontal cylindrical duct of...Ch. 9 - Evaluate the displacement thickness and the...Ch. 9 - Evaluate the displacement thickness and the...Ch. 9 - A laboratory wind tunnel has a test section 25 cm...Ch. 9 - Air flows in the entrance region of a square duct,...Ch. 9 - A flow of 68F air develops in a flat horizontal...Ch. 9 - A flow of air develops in a horizontal cylindrical...Ch. 9 - Using numerical results for the Blasius exact...Ch. 9 - Using numerical results obtained by Blasius (Table...Ch. 9 - Using numerical results obtained by Blasius (Table...Ch. 9 - A smooth flat plate 2.4 m long and 0.6 m wide is...Ch. 9 - Consider flow of air over a flat plate. On one...Ch. 9 - A thin flat plate, L = 9 in. long and b = 3 ft...Ch. 9 - For a laminar boundary layer on a flat plate,...Ch. 9 - Air at atmospheric pressure and 20C flows over...Ch. 9 - A thin flat plate is installed in a water tunnel...Ch. 9 - Assume laminar boundary-layer flow to estimate the...Ch. 9 - Assume laminar boundary-layer flow to estimate the...Ch. 9 - Assume laminar boundary-layer flow to estimate the...Ch. 9 - Prob. 34PCh. 9 - Water at 10C flows over a flat plate at a speed of...Ch. 9 - Use the momentum integral equation to derive...Ch. 9 - A smooth flat plate 1.6 ft long is immersed in 68F...Ch. 9 - Prob. 38PCh. 9 - A developing boundary layer of standard air on a...Ch. 9 - Assume the flow conditions given in Example 9.3....Ch. 9 - A flat-bottomed barge having a 150 ft 20 ft...Ch. 9 - European InterCity Express trains operate at...Ch. 9 - Grumman Corp. has proposed to build a magnetic...Ch. 9 - Repeat Problem 9.32, for an air flow at 80 ft/s,...Ch. 9 - The velocity profile in a turbulent boundary-layer...Ch. 9 - The U.S. Navy has built the Sea Shadow, which is a...Ch. 9 - The two rectangular smooth flat plates are to have...Ch. 9 - Standard air flows over a horizontal smooth flat...Ch. 9 - Air at standard conditions flows over a flat...Ch. 9 - A uniform flow of standard air at 60 m/s enters a...Ch. 9 - A laboratory wind tunnel has a flexible upper wall...Ch. 9 - Air flows in a cylindrical duct of diameter D = 6...Ch. 9 - Perform a cost-effectiveness analysis on a typical...Ch. 9 - Table 9.1 (on the web) shows the numerical results...Ch. 9 - A fluid flow enters the plane-wall diffuser that...Ch. 9 - For flow over a flat plate with zero pressure...Ch. 9 - A flat-bottomed barge, 80 ft long and 35 ft wide,...Ch. 9 - A towboat for river barges is tested in a towing...Ch. 9 - Plot the local friction coefficient cf, the...Ch. 9 - A smooth plate 3 m long and 0.9 m wide moves...Ch. 9 - Resistance of a barge is to be determined from...Ch. 9 - A nuclear submarine cruises fully submerged at 27...Ch. 9 - You are asked by your college crew to estimate the...Ch. 9 - The drag coefficient of a circular disk when...Ch. 9 - A steel sphere of 0.25 in. diameter has a velocity...Ch. 9 - A steel sphere (SG = 7.8) of 13 mm diameter falls...Ch. 9 - A sheet of plastic material 0.5 in. thick, with...Ch. 9 - As part of the 1976 bicentennial celebration, an...Ch. 9 - What constant speed will be attained by a lead (SG...Ch. 9 - Assuming a critical Reynolds number of 0.1,...Ch. 9 - Glass spheres of 0.1 in. diameter fall at constant...Ch. 9 - A rotary mixer is constructed from two circular...Ch. 9 - Calculate the drag of a smooth sphere of 0.3 m...Ch. 9 - Calculate the drag of a smooth sphere of 0.5 m...Ch. 9 - A cylindrical chimney 0.9 m in diameter and 22.5 m...Ch. 9 - The resistance to motion of a good bicycle on...Ch. 9 - Ballistic data obtained on a firing range show...Ch. 9 - A standard marine torpedo is 0.533 m in diameter...Ch. 9 - A large truck has an essentially boxlike body that...Ch. 9 - At a surprise party for a friend youve tied a...Ch. 9 - A 0.5-m-diameter hollow plastic sphere containing...Ch. 9 - A simple but effective anemometer to measure wind...Ch. 9 - The Willis Tower (formerly the Sears Tower) in...Ch. 9 - It is proposed to build a pyramidal building with...Ch. 9 - Calculate the drag forces on a 1/200 scale model...Ch. 9 - A circular disk is hung in an air stream from a...Ch. 9 - A vehicle is built to try for the land-speed...Ch. 9 - An F-4 aircraft is slowed after landing by dual...Ch. 9 - A tractor-trailer rig has frontal area A = 102 ft2...Ch. 9 - A 180hp sports car of frontal area 1.72 m2, with a...Ch. 9 - An object falls in air down a long vertical chute....Ch. 9 - Prob. 99PCh. 9 - A light plane tows an advertising banner over a...Ch. 9 - The antenna on a car is 10 mm in diameter and 1.8...Ch. 9 - Consider small oil droplets (SG = 0.85) rising in...Ch. 9 - Standard air is drawn into a low-speed wind...Ch. 9 - A small sphere with D = 6 mm is observed to fall...Ch. 9 - A tennis ball with a mass of 57 g and diameter of...Ch. 9 - A water tower consists of a 12-m-diameter sphere...Ch. 9 - A cast-iron 12-pounder cannonball rolls off the...Ch. 9 - A rectangular airfoil of 40 ft span and 6 ft chord...Ch. 9 - A rectangular airfoil of 9 m span and 1.8 m chord...Ch. 9 - Why is it possible to kick a football farther in a...Ch. 9 - If CL = 1.0 and CD = 0.05 for an airfoil, then...Ch. 9 - A wing model of 5 in. chord and 2.5 ft span is...Ch. 9 - A barge weighing 8820 kN that is 10 m wide, 30 m...Ch. 9 - A spherical sonar transducer with 15 in. diameter...Ch. 9 - While walking across campus one windy day, an...Ch. 9 - If the mean velocity adjacent to the top of a wing...Ch. 9 - The NACA 23015 airfoil is to move at 180 mph...Ch. 9 - A human-powered aircraft has a gross weight of 240...Ch. 9 - WiffleTM balls made from light plastic with...Ch. 9 - A model airfoil of chord 6 in. and span 30 in. is...Ch. 9 - An antique airplane carries 50 m of external guy...Ch. 9 - How do cab-mounted wind deflectors for...Ch. 9 - An airplane with an effective lift area of 25 m2...Ch. 9 - The U.S. Air Force F-16 fighter aircraft has wing...Ch. 9 - A light airplane, with mass M = 1000 kg, has a...Ch. 9 - A light airplane has 35-ft effective wingspan and...Ch. 9 - Assume the Boeing 727 aircraft has wings with NACA...Ch. 9 - Jim Halls Chaparral 2F sports-racing cars in the...Ch. 9 - Some cars come with a spoiler, a wing section...Ch. 9 - Roadside signs tend to oscillate in a twisting...Ch. 9 - Air moving over an automobile is accelerated to...Ch. 9 - A class demonstration showed that lift is present...Ch. 9 - Rotating cylinders were proposed as a means of...Ch. 9 - A baseball pitcher throws a ball at 80 mph. Home...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
The beam is made of steel having an allowable normal stress of allow = 150 MPa and an allowable shear stress of...
Mechanics of Materials (10th Edition)
Determine the normal stress in each member of the truss structure. All joints are ball joint, and the material ...
Introduction To Finite Element Analysis And Design
At the instant shown, A has a speed of 60ft/sand is increasing its speed at the rate of 15 ft/s2 until it trave...
Engineering Mechanics: Dynamics (14th Edition)
ICA 8-54
When we drive our car at 100 feet per second [ft/s], we measure an aerodynamic force (called drag) of ...
Thinking Like an Engineer: An Active Learning Approach (4th Edition)
If cable AD is tightened by a turnbuckle and develops a tension of 1300 lb, determine the tension developed in ...
INTERNATIONAL EDITION---Engineering Mechanics: Statics, 14th edition (SI unit)
ICA 8-48
We go out to sunbathe on a warm summer day. If we soak up 100 British thermal units per hour [BTU/h] o...
Thinking Like an Engineer: An Active Learning Approach (3rd Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- 3. Use scale analysis to find an expression for S/L and Nu, for flow over a flat plate with both boundary layers of equal thickness (8=ST)arrow_forwardProb.7. A smooth flat plate of length 5 m and width 2 m is moving with a velocity of 4 m/s in stationary air of density 1.25 kg/m and kinematic viscosity 1.5 x 10-5 m2/s. Determine thickness of the boundary layer at the trailing edge of the smooth plate. Find the total drag on one side of the plate assuming that the boundary layer is turbulent from the very beginning.arrow_forwardAmbient Air has a temperature of 20°C and creates a boundary layer which is beside a solid walI, follows a sinusoidal velocity profile. The boundary layer thickness is around 7mm having a peak velocity of 9 m/s. Solve for the shear stress in a boundary layer at height (y) equal to: a. 0 b. 3.5mm Umax 9 m/s %D c. 7mm µ = 1.85 x 10 -5 Pa•s Peak 7 mm sin Sine Wave U = Umax Sinsarrow_forward
- Reference 12 contains inviscid theory calculations for the upper and lower surface velocity distributions V(x) over an airfoil, where x is the chordwise coordinate. A typical re- sult for small angle of attack is as follows: xlc VIU„(upper) VIU„(lower) 0.0 0.0 0.0 0.025 0.97 0.82 0.05 1.23 0.98 0.1 1.28 1.05 1.13 0.2 1.29 0.3 1.29 1.16 0.4 1.24 1.16 0.6 1.14 1.08 0.8 0.99 0.95 1.0 0.82 0.82 Use these data, plus Bernoulli's equation, to estimate (a) the lift coefficient and (b) the angle of attack if the airfoil is symmetric.arrow_forwardRepeat the question below specifically part b. but now consider a turbulent boundary layer for which the velocity profile can be approximated by a power law equation, u/U = (y/δ)1/6 Compare with results given in text Example 9.6 for 1/7 power law profile. https://www.bartleby.com/questions-and-answers/consider-a-laminar-boundary-layer-flow-over-a-flat-plate-for-which-the-velocity-profile-can-be-appro/4e3bc9ec-d14a-4139-ac11-353c08916c31arrow_forwardAir at 15°C forms a boundary layer near a solid wall. The velocity distribution in the boundary layer is given by: u/U = 1- exp (-2y/8), where U 35 m/sec. and 8 = 0.8 cm. Find the shear stress at wall (y 0).arrow_forward
- B) for the velocity profiles given below, state whether the boundary layer has separated or on the verge of separation or will remain attached ( i) u/U=2(y/8) -(y/8)² ii) u/U=-2(y/8) +0.5(y/8)³ iii) u/U-1.5(y/8) +0.5(y/8)³ Q3: Find the displacement, momentum thickness and energy thickness for the velocity distribution in the boundary layer: F u/U=0.5(y/8) + 1.5(y/8)³ Q4: A) Find the velocity distribution and expression of the maximum velocity and shear stress for a flow between two stationary plates. C B) A laminar flow of oil between two horizontal fixed parallel plates with a maximum velocity 2 m/s and 100mm apart. Canulate the pressure gradient and shear stress. Take µ-2.4525 s/m².arrow_forwardA gas at 20°C and 1 atm flow at 6 ft/s past a thin flat plate.At x = 3 ft, the boundary layer thickness is 0.052 ft.Assuming laminar flow, which of the gases in Table A.4 isthis likely to be?arrow_forwardWe are testing a flat plate of length L = 1.125 m and width W = 0.225 m in a stream of air flowing with a velocity of 20 m/s. In test case 1, the air is flowing parallel to L and in test case 2 air is flowing parallel to W. Find: What portion of the boundary layer flow is laminar in each case? What is the highest laminar boundary layer thickness in each case? Assuming the flow is entirely turbulent over the plate, calculate the drag force in both test cases Take air density as 1.2 kg/m3 and its viscosity as μ=18×10−6μ=18×10−6 N.s/m2.arrow_forward
- 31) Estimate the drag force on the fuselage shown below for a cruising speed of 200 m/s at 10,000 m. 8 m 5 m W m W = 20 m Hint 1: To calculate the drag force split the fuselage into 4 parts: front hemisphere, cylindrical body, vertical stabilizer, back hemisphere. Model the front and back hemispheres as flow over a sphere. For simplicity treat the cylindrical body and vertical stabilizer as flat plates Hint 2: Use Ca vs Reynolds number graphs for sphere and flat plate. If your Reynolds number is greater/smaller than the Cd vs Reynolds graph range, you can instead use the greatest/smallest number available on the graph.arrow_forward6- A uniform free stream of air at 0.8 m/s flows over a flat plate (4 m long x 1 m wide). Assuming the boundary layer to be laminar on the plate and the velocity profile is: и Find the ratio of the drag force on the front half portion to the drag %3D U force on the rear half portion of the plate. (p = 1.2 kg/m ; v= 1.51×10* m³/s) [2.42]arrow_forwardA NACA 2412 airfoil with a chord of 0.64m is flying in an airstream of standard sea level conditions. The freestream velocity is 70 m/s. Given the lift per unit span is 1,254 N/m. By using the experimental data for NACA 2412 data plot in Figure Q1c, investigatethe angle of attack of the airfoil and the analyze the value of drag per unit spanof the airfoil. Given that at standard sea level, ?=1.789×10-5 kg/m.s.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
![Text book image](https://www.bartleby.com/isbn_cover_images/9780190698614/9780190698614_smallCoverImage.gif)
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
![Text book image](https://www.bartleby.com/isbn_cover_images/9780134319650/9780134319650_smallCoverImage.gif)
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
![Text book image](https://www.bartleby.com/isbn_cover_images/9781259822674/9781259822674_smallCoverImage.gif)
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
![Text book image](https://www.bartleby.com/isbn_cover_images/9781118170519/9781118170519_smallCoverImage.gif)
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
![Text book image](https://www.bartleby.com/isbn_cover_images/9781337093347/9781337093347_smallCoverImage.gif)
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
![Text book image](https://www.bartleby.com/isbn_cover_images/9781118807330/9781118807330_smallCoverImage.gif)
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Unit Conversion the Easy Way (Dimensional Analysis); Author: ketzbook;https://www.youtube.com/watch?v=HRe1mire4Gc;License: Standard YouTube License, CC-BY