Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 9, Problem 2ASRQ
To determine
The correct statement about the piston slap between the arguments given by two Technicians A & B.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Why is it important to loosen the cylinder head bolts in the recommended order?
Technician A says that a cylinder wall with too smootha surface will prevent the piston rings from seatingproperly. Technician B says that a cylinder wall shouldhave a crosshatch honing pattern. Who is correct?a. Technician Ab. Technician Bc. Both A and Bd. Neither A nor B
Why are wear rings used on cylinder pistons?
Chapter 9 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 9 - Prob. 1RQCh. 9 - Describe what takes place during the four strokes...Ch. 9 - As an engines compression ratio increases, what...Ch. 9 - What test can be performed to check the efficiency...Ch. 9 - Describe tappet noise.Ch. 9 - Which of the following statements about engines is...Ch. 9 - Which stroke in the four-stroke cycle begins as...Ch. 9 - True or False? In an HCCI engine, combustion...Ch. 9 - Which of the following is not a true statement...Ch. 9 - True or False? SAE mandates that engine, when...
Ch. 9 - Technician A says head gasket thickness has an...Ch. 9 - Prob. 12RQCh. 9 - The stroke of an engine is the crank throw half...Ch. 9 - True or False? The camshaft is always located in...Ch. 9 - Which of the following is an expression of how...Ch. 9 - While diagnosing the cause for blue smoke from the...Ch. 9 - Prob. 2ASRQCh. 9 - While determining the cause for air leaking out of...Ch. 9 - While diagnosing the cause for an engine having...Ch. 9 - While looking at the results of an oil pressure...Ch. 9 - A vehicle is producing a sharp, metallic rapping...Ch. 9 - While conducting an engine vacuum test; Technician...Ch. 9 - While determining the most likely problem of an...Ch. 9 - When a customer states that black exhaust smoke is...Ch. 9 - Technician A says that if an engine had good...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Technician A says that piston ring end gaps should be the same for each ring on a piston. Technician B says that piston ring end gaps should be aligned before installing the piston into its bore. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTechnician A says that a cylinder wall with too smooth a surface will prevent the piston rings from seating properly. Technician B says that a cylinder wall should have a crosshatch honing pattern. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhile discussing the common causes for cracks developing in a cylinder block or head: Technician A says that the chilling of a hot engine by a sudden rush of cold water or air over the surf ace may cause cracking. Technician B says that excessive overheating is a common cause. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- While discussing the reasons for resurfacing a cylinder head; Technician A says it should be resurfaced to make it flat and very smooth so the head gasket can seal properly during engine assembly. Technician B says that it can be resurfaced to raise the compression. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhile determining the cause for air leaking out of the oil throttle body during a cylinder leakage test: Technician A says that a burnt intake valve is indicated. Technician B says that a warped cylinder head or bad head gasket is indicated. Who is correct? Technician A Technician B Both A and B d. Neither A nor Barrow_forwardWhich of the following are not typically found in the block of a modern engine? a. Pistons b. Crankshaft c. Valves d. Oil pumparrow_forward
- Technician A says an engine may use one or more valve springs per valve. Technician B says additional valve springs are used to control vibration and increase total pressure. Who is correct? a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forwardThe piston rings are used to act as a seal between the piston and cylinder head a. FALSE b. TRUEarrow_forwardA six-cylinder engine has a 1 5 3 6 2 4 firing order. Technician A says that after cylinder number 1 begins its intake stroke, the crankshaft will have to travel 240° before cylinder number 3 begins its intake stoke. Technician B says that when cylinder number 3 and 4 are at TDC, cylinders number 5 and 2 are at BDC. Who is correct and explain why? Technician A Technician B Both A and B Neither A nor Barrow_forward
- Carbon deposits on the intake valve or seat may cause the valve not to close properly. Tech a says that the flywheel will be harder to spin when starting the engine. Tech b says that the engine will loose power. Who is correct?arrow_forwardWhich of the following is not measured with a feelergauge set?a. Piston ring side clearanceb. Flywheel runoutc. Crankshaft end playd. Spark plug gaparrow_forwardTechnician A says that crankshaft counterweights offset the weight of the connecting rods and pistons. Technician B says that crankshaft counterweights are used to dampen crankshaft torsional vibrations. Who is correct? Technician A Technician B Both A and B d. Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,