Automotive Technology: A Systems Approach - With Manual and Access
6th Edition
ISBN: 9781305513235
Author: ERJAVEC
Publisher: Cengage
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 9, Problem 2ASRQ
To determine
The correct statement about the piston slap between the arguments given by two Technicians A & B.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A vehicle makes a loud clicking sound during a left turn; during a right turn, the clicking noise is still apparent but is less pronounced.
Technician A says that the left inner CV joint may be the source of the noise.
Technician B says that the left outer CV joint may be causing the noise.
Who is correct?
O a. A only
Ob.B only
O c. Both A and B
O d. Neither A nor B
A six-cylinder engine has a 1 5 3 6 2 4 firing order. Technician A says that after cylinder number 1 begins its intake stroke, the crankshaft will have to travel 240° before cylinder number 3 begins its intake stoke. Technician B says that when cylinder number 3 and 4 are at TDC, cylinders number 5 and 2 are at BDC.
Who is correct and explain why?
Technician A
Technician B
Both A and B
Neither A nor B
The CV joint boots on the left side of a vehicle appear to be squeezed together; the boots on the right side of the vehicle appear to be stretched apart.
Technician A says that one or more of the engine/transaxle's mounts may be broken.
Technician B says that one or more of the engine/transaxle's subframe mounts may be broken.
Who is correct?
O a. A only
O b.B only
C. Both A and B
O d. Neither A nor B
Chapter 9 Solutions
Automotive Technology: A Systems Approach - With Manual and Access
Ch. 9 - Prob. 1RQCh. 9 - Describe what takes place during the four strokes...Ch. 9 - As an engines compression ratio increases, what...Ch. 9 - What test can be performed to check the efficiency...Ch. 9 - Describe tappet noise.Ch. 9 - Which of the following statements about engines is...Ch. 9 - Which stroke in the four-stroke cycle begins as...Ch. 9 - True or False? In an HCCI engine, combustion...Ch. 9 - Which of the following is not a true statement...Ch. 9 - True or False? SAE mandates that engine, when...
Ch. 9 - Technician A says head gasket thickness has an...Ch. 9 - Prob. 12RQCh. 9 - The stroke of an engine is the crank throw half...Ch. 9 - True or False? The camshaft is always located in...Ch. 9 - Which of the following is an expression of how...Ch. 9 - While diagnosing the cause for blue smoke from the...Ch. 9 - Prob. 2ASRQCh. 9 - While determining the cause for air leaking out of...Ch. 9 - While diagnosing the cause for an engine having...Ch. 9 - While looking at the results of an oil pressure...Ch. 9 - A vehicle is producing a sharp, metallic rapping...Ch. 9 - While conducting an engine vacuum test; Technician...Ch. 9 - While determining the most likely problem of an...Ch. 9 - When a customer states that black exhaust smoke is...Ch. 9 - Technician A says that if an engine had good...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- While discussing the misfire monitor: Technician A says that while detecting type A misfires, the monitor checks cylinder misfiring over a 500-revolution period. Technician B says that while detecting type B misfires, the monitor checks cylinder misfires over a 1,000-revolution period. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTechnician A says that piston ring end gaps should be the same for each ring on a piston. Technician B says that piston ring end gaps should be aligned before installing the piston into its bore. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhile discussing the common causes for cracks developing in a cylinder block or head: Technician A says that the chilling of a hot engine by a sudden rush of cold water or air over the surf ace may cause cracking. Technician B says that excessive overheating is a common cause. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- While discussing the reasons for resurfacing a cylinder head; Technician A says it should be resurfaced to make it flat and very smooth so the head gasket can seal properly during engine assembly. Technician B says that it can be resurfaced to raise the compression. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhile determining the cause for air leaking out of the oil throttle body during a cylinder leakage test: Technician A says that a burnt intake valve is indicated. Technician B says that a warped cylinder head or bad head gasket is indicated. Who is correct? Technician A Technician B Both A and B d. Neither A nor Barrow_forwardTechnician A says that positive valve stem seals fit tightly around the top of the valve guide. Technician B says that positive stem seals scrape oil off the valve as it moves up and down. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- Technician A says that a cylinder wall with too smooth a surface will prevent the piston rings from seating properly. Technician B says that a cylinder wall should have a crosshatch honing pattern. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhile discussing the results of an oil pressure test: Technician A says that when the fluid pressures are high, internal leaks, a clogged filter, low oil pump out put, or a faulty pressure regulator valve are indicated. Technician B says that if the fluid pressure increased at the wrong time, an internal leak at the servo or clutch seal is indicated. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardWhile diagnosing the cause for an engine having good results from a compression test and cylinder leakage test but poor results from a cylinder power balance test: Technician A says that incorrect valve timing is the most likely cause. Technician B says that a severely worn cam lobe is a likely cause. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- Solve fast pleasearrow_forwardTechnician A says that you may be able to smell antifreeze from a leaking heater core. Technician B says that you may be able to hear a loose belt when the engine is running. Who is correct? Select one: a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardWhy is it important to loosen the cylinder head bolts in the recommended order?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning