EBK AUTOMOTIVE TECHNOLOGY
5th Edition
ISBN: 8220100659843
Author: Halderman
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 9, Problem 5CQ
Two technicians are discussing torque wrenches. Technician A says that a torque wrench is capable of tightening a fastener with more torque than a conventional breaker bar or ratchet. Technician B says that a torque wrench is used to apply a known amount of force to the fastener. Which technician is correct?
a. Technician A only
b. Technician B only
c. Both Technicians A and B
d. Neither Technician A nor B
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Technician A says a metric bolt with the marking of 8.9 has more yield strength than a 10.9 bolt. Technician B says only grade 8 nuts should be used on 10.9 rated bolt. Who is correct?
True or False: Frictionless 2D Pins and 2D Hinges have reactions in both the x and y directions. True or False?
Differentiate between a fast and loose pulley.
Chapter 9 Solutions
EBK AUTOMOTIVE TECHNOLOGY
Ch. 9 - Why are wrenches offset 15 degrees?Ch. 9 - What are the other names for a line wrench?Ch. 9 - What are the standard automotive drive sizes for...Ch. 9 - Which type of screwdriver requires the use of a...Ch. 9 - What is inside a dead-blow hammer?Ch. 9 - Prob. 6RQCh. 9 - When working with hand tools, always _____. a....Ch. 9 - Prob. 2CQCh. 9 - Prob. 3CQCh. 9 - Prob. 4CQ
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- True or False 1. It is acceptable to use a hoist to lift something that weighs more than the rating on the hoist when the load is lifted carefully. 2. Typically, combustible material accidents occur at higher temperatures while flammable material accidents occur at room temperature. 3. Water reactive chemicals include calcium carbide, cyclooctene, metal hydrides, and metals like sodium and potassium. 4. When driving material lifting equipment, workers should maintain at least a 5-foot clearance from overhead power lines. 5. Workers should use at least 2 straps placed equally from the center when lifting a long I-beam. ******************************************************************************************** Multiple Choice 1. Which of the following chemicals is not considered a liver toxin? A. Glacial acetic acid B. Carbon Tetrachloride C. Ethanol D. Trichloroethylene 2. Which of the following is a safety practice intended to protect workers from a lightning strike? A. Use a metal…arrow_forwardFrom the following identify a true statement regarding the adjustment of drive belt tension. a. Less than 8 mm should be the correct a deflection for each belt which is under tension b. More than 6 mm should be the correct a deflection for each belt which is under tension c. More than 8 mm should be the correct a deflection for each belt which is under tension. d. More than 6 mm and less than 8 mm should be the correct a deflection for each belt which is under tension.arrow_forwardWhen reviewing the procedure for replacing an axle boot, Technician A says that the position of the old boot should be marked on the shaft before removing it. Technician B says that if the boot is dimpled or collapsed after the new boot is installed, a dulled screwdriver should be used to allow air to enter the boot. Who is correct? O a. A only O b. B only O c. Both A and B O d. Neither A nor Barrow_forward
- When installing a new release bearing, Technician A says the outer surface of thetransmission's front bearing retainer should be lubricated. Technician B says the release lever and pivot shuold be lubricated who is correct? a. techincian A b. Technician B c. both A and B d. Neither A or Barrow_forwardTechnician A says that load-carrying ball jointsshould always have some play in them. Technician Bsays that follower ball joints should never have someplay in them. Who is correct?a. Technician A onlyb. Technician B onlyc. Both A and Bd. Neither A nor Barrow_forwardA vehicle makes a loud clicking sound during a left turn; during a right turn, the clicking noise is still apparent but is less pronounced. Technician A says that the left inner CV joint may be the source of the noise. Technician B says that the left outer CV joint may be causing the noise. Who is correct? O a. A only Ob.B only O c. Both A and B O d. Neither A nor Barrow_forward
- Q 2/ True or false 1- Casing pipe is used to rotate the bit and circulate the drilling fluid. 2- On one side of the fault line the strata has been displaced only upwards or downwards 3- The person who is in charge of the drilling rig and crew is a mud engineer. 4- The cable tool drilling an old method of well drilling used before rotary methods. 5- When the bit is needed to rotate exclusively, downhole motor is used. 6- When the valve allows flow to pass in a definite direction is called check valve. 7- Elevator is equipment used to raise or lower pipe into the wellbore. 8- When the drilling mud to a scape to the formation due to fractures or highly permeable beds, a lost circulation has happened. 9- During the offshore drilling the drilling rig is mounted on a floating vessel. 10- Kick is an entry of formation fluids (oil, gas or water) into the wellbore caused when the formation pressure less than the pressure exerted by the mud column.arrow_forwardA single fixed pulley simply changes the direction of the pull, but it doesn't ___. A. Change the speed B. Reduce the force you need C. Do work (answer only)arrow_forwardTRUE OR FALSE ? QUESTION : In the absence of collar friction, the power screw described in the previous two problems is self-locking.arrow_forward
- Technician A uses a micrometer to measure the connectingrod journal for taper. Technician B uses amicrometer to measure the connecting rod journalfor out-of-roundness. Who is correct?a. Technician Ab. Technician Bc. Both A and Bd. Neither A nor Barrow_forwardWhich of the following threads is ideal for power transmission? a. Buttress Thread b. Square Thread c. Metric Thread d. ACME Thread Cold working of steel is defined as working a. Below its recrystallization temperature b. At two thirds of the melting temperature of the metal c. At its recrystallization temperature d. Above its recrystallization temperaturearrow_forwardTechnician A says that some small cracks in the accessory drive belt may be within tolerance. Technician B says that serpentine belts can be checked with a wear gauge. Who is correct? Select one: a. Technician A only b. Technician B only C. Both A and B d. Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Stresses Due to Fluctuating Loads Introduction - Design Against Fluctuating Loads - Machine Design 1; Author: Ekeeda;https://www.youtube.com/watch?v=3FBmQXfP_eE;License: Standard Youtube License