A gold on iron oxide catalyst was prepared by wet impregnation and dried at 110 °C overnight. The sample was then subjected to XPS analysis, and the following peak areas determined from the high resolution spectra: Integrated Peak Area Sensitivity Factor Element C 13587 0.278 0.78 5187 13587 4000 Fe 2.957 Au 6.25

A gold on iron oxide catalyst was prepared by wet impregnation and dried at 110 °C overnight. The sample was then subjected to XPS analysis, and the following peak areas determined from the high resolution spectra: Integrated Peak Area Sensitivity Factor Element C 13587 0.278 0.78 5187 13587 4000 Fe 2.957 Au 6.25

Appl Of Ms Excel In Analytical Chemistry

2nd Edition

ISBN:9781285686691

Author:Crouch

Publisher:Crouch

Chapter12: Spectrochemical Methods

Section: Chapter Questions

Problem 7P

See similar textbooks

Similar questions

In order to improve the peptide separation by using a HPLC system, trifluoroacetic acid acts as mobile-phase modifier was added during the preparation of mobile phase. The preparation was performed by a postgraduate student as following:“2.851 g trifluoroacetic acid (MW: 114.02 g/mol) was made up to 500 cm3 in a graduated flask. To this solution, 50 cm3 of ethanol was added, and after mixing the mobile phase was placed in the solvent reservoir and pumping was commenced at 1.5 cm3 min-1.”Based on the given preparation procedure, identify THREE mistakes that were made.
Glycolic acid is used in the textile industry as a dyeing and tanning agent. Given that its acid dissociation constant (Ka) is 1.47 × 10-4 and its partition coefficient (KD) between water and benzene is 3.22, calculate the extraction efficiency of a single extraction when 50.00 mL of a 0.025 M aqueous solution of glycolic acid buffered to a pH of 3.00, is extracted once with 50.00 mL of benzene.
Using the absorbance of [FeSCN]+2 at the wavelength of maximum absorption which you obtained in part B, and the diameter of the tube, obtained in part A,calculate the molar extinction coefficient. given info: Concentration of Fe3+ stock solution, C1 = 0.001 M Volume of stock Fe3+ solution pipetted, V1 = 25mL Concentration of diluted stock solution, C2 = 0.0004 M Volume of Fe2+ solution and KSCN (upon mixing) = 10mL Weight of KSCN = 1g The reaction taking place is given as: The reaction taking place is given as: F e 3+ (aq) + SC N − (aq) ⇔Fe [SCN] 2+ (aq) the concentration of [FeSCN]2+ after the mixing of Fe3+ and SCN- is 2.5 x 10-3 M. Moles of [FeSCN]2+ = 2.5 x 10-5 moles Diameter:1.2cm The wavelength at which maximum absorption takes place is = 480 nm
It has been notice that adulteration of palm oil with carcinogenic dyes are on rise. Use knowledge in analytical process to systematically outline a protocol to follow to process adulterated palm oil to gain quantitative and qualitative information spectroscopically about any added toxic dye. Explain also the basis of your protocol of choice.
It has been noticed adulteration of palm oil with carcinogenic dyes are on rise. Use knowledge in analytical processes to systematically outline a protocol you will follow to process adultered palm oil to gain qualitative and quantitative information spectroscopically about any added toxic dye. Explain in details with good introduction , conclusion on the basis for your protocol of choice.
(a) A sample of body serum is to be analysed for sodium by flame emission spectroscopy. 1.00cm3 aliquot of serum was pipetted into each of two 50.0 cm3 volumetric flasks. The firstflask was diluted to volume with deionised water. The absorbance of this first solution was0.350. To the second flask 10.0 cm3 of a 25.0 ppm sodium standard was added and theflask made up to volume with deionised water. The absorbance of this second solution was0.720.(i) Calculate the concentration of the sodium in the body serum in mg dm–3
Discuss and explain the differences that you observe when calibrating with both techniques (AAS and ICP-AES).
i) Find the differences between the AES and XPS in terms of principle and information obtained from the spectra. ii) Why AFM is mostly utilized microscopic method for the determination of the thickness of the film?
Two species A and B are known to have water/hexane partition coefficient of 5.99 and 6.16. They are separated by elution on silica gel with hexane as eluent. The ratio for the packing VS/VM =0.425a) What column length should be used to provide a resolution of 1.5 if the plate height ofthe packing is 1.5 ×10-3 cm? b) If the flow rate is 6.75 cm min-1, how long will it take to elute the two species?
What is the concentration (M) of the following compound as measured in a 1.000 cm cuvette: Molar absorptivity constant: 3525 (M*cm)-1 and Absorption: 0.5334 Hint: Use the Beer law to solve this problem Group of answer choices 1.513E-04 1.513E+04 1.513191E-04 1.513191E+04 1.5E-04
A sample of body serum is to be analysed for sodium by flame emission spectroscopy. 1.00cm' aliquot of serum was pipetted into each of two 50.0cm' volumetric flasks. The first flask was diluted to volume with deionised water. The absorbance of this first solution was0.350. To the second flask 10.0 cm' of a 25.0 ppm sodium standard was added and the flask made up to volume with deionised water. The absorbance of this second solution was 0.720.(i) Calculate the concentration of the sodium in the body serum in mg dm-3.
The following calibration data were obtained by an atomic absorption spectrophotometric (AAS) method for the determination of mercury in an herbal product. 1. Calculate the calibration sensitivity.2. Calculate the coefficient of variation for the mean at 6.00 ppm 3. What is the detection limit for the method? 4. What is the limit of quantitation for the method?