A peak with a retention time of 10 minutes has a width at half-height of 7.6 s neighboringpeak is eluted 15 s later with W½ = 7.5 s.(4)Find out the resolution for these two components.(a)(b)Is this resolution value good for quantitative analysis, why?(c)What difference in retention times is required for an adequate resolution of 1.5?

given values from the above queston are ]- retention time for component 1= tr1 = 15sec. retention…

A peak with a retention time of 10 minutes has a width at half-height of 7.6 s neighboring peak is eluted 15 s later with W½ = 7.5 s. (4) (a) Find out the resolution for these two components. (b) Is this resolution value good for quantitative analysis, why? (c) What difference in retention times is required for an adequate resolution of 1.5?

A peak with a retention time of 10 minutes has a width at half-height of 7.6 s neighboring peak is eluted 15 s later with W½ = 7.5 s. (4) (a) Find out the resolution for these two components. (b) Is this resolution value good for quantitative analysis, why? (c) What difference in retention times is required for an adequate resolution of 1.5?

Fundamentals Of Analytical Chemistry

9th Edition

ISBN:9781285640686

Author:Skoog

Publisher:Skoog

Chapter29: Mass Spectrometry

Section: Chapter Questions

Problem 29.7QAP

See similar textbooks

Similar questions

A peak with a retention time of 407s has a width at half-height of 7.6 seconds. A neighboring peak is eluted 17 seconds later with w1/2 = 9.4 seconds. What is the difference in retention time required for an adequate resolution of 1.5?
Substances A and B have retention times of 12.75 and 14.28 min, respectively, on a 30.0-cm column. An unretained species passes through the column in 1.10 min. The peak widths (at base) for A and B are 1.11 and 1.27 min, respectively. What is the resolution?
Consider the separation of components A and B on a GC column. The retention time for component A is 1.4 min and for component B is 2.1 min. The width at the base for the peak due toA is 0.38 min and for the peak due to B is 0.53 min. Calculate the resolution, R, and tell whetherthe two peaks are considered to be resolved and why.
Two components in an HPLC separation have retention times thatdiffer by 22 s. The first peak elutes in 10.5 min and the peakwidths are approximately equal. Use a spreadsheet to find theminimum number of theoretical plates needed to achieve thefollowing resolution, Rs, values: 0.50, 0.75, 0.90, 1.0, 1.10, 1.25,1.50, 1.75, 2.0, and 2.5. How would the results change if peak 2were twice as broad as peak 1?
A chromatogram of a mixture of species A, B, and C provided the following data: a) Define "Retention time". b) Calculate the resolution between species A and B. c) Calculate the retention time of species B necessary to separate it from species A with a resolution of 1.5.
In a HPLC separation of two compounds, A and B, the retention times observed are 3.5 min. for A and 4.5 min. for B on a 15 cm column. The retention time for the mobile phase is 1.0 min. The peak widths (at the base) for A and B are 0.5 and 0.7 min respectively. Calculate the following: (i) The capacity factor of A and B. (ii) The peak resolution. (iii) The average number of theoretical plates in the column
Compare the resolution for the two components A and B when (tr)b = 5.0 min and (trla = 4.4 min using: 1-Colmn with L = 900 mm, H = 1.0 mm 2- Column with L= 900 mm, H = 3 mm
Substance A and B were found to have retention times of 16.40 and 17.63 min. respectively, on a 30cm HPLC column. An unretained species passed through the column in 1.30 min. The peak widths at base for A and B were 1.11 and 1.21 min, respectively. Calculate the a.) Column resolution b.) the average nbumber of plates in the column and the plate height.
(b) For column 1(i) What are the unadjusted retention times for components A and B?
Substances A and B have retention times of 16.40 and 17.63 min, respectively,on a 30.0-cm column. An unretained species passes through the column in 1.30 min. The peakwidths (at base) for A and B are 1.11 and 1.21 min, respectively. Calculate(a) the column resolution,(b) the average number of plates in the column,(c) the plate height,(d) the length of column required to achieve a resolution of 1.5.
What characteristic makes a photodiode array spectrophotometer suitable for measuring the spectrum of a compound as it emerges from a chromatography column and a dispersive spectrophotometer not suitable? What is the disadvantage of the photodiode array spectrophotometer?
Two components in an HPLC separation have retention times that differ by 15 s. The first peak elutes in 9.0 min, and the peak widths are approximately equal. The dead time to was 65 s. Use a spreadsheet to find the minimum number of theoretical plates needed to achieve the following resolution. R. values: 0.50 0.75, 0.90, 1.0, 1.10. 1.25, 1.50. L75. 2.0 and 2.5. How would the results change if peak 2 were twice as broad as peak 1?