(b) Based on the performance and validation methods, explain the distinctions between the two tems listed below: (1) linearity and coefficient of detemination (ii) intra-day and inter-day precision (ii) absolute recovery and relative recovery (iv) limit of detection and limit of quantification (V) selectivity and specificity

(b) Based on the performance and validation methods, explain the distinctions between the two tems listed below: (1) linearity and coefficient of detemination (ii) intra-day and inter-day precision (ii) absolute recovery and relative recovery (iv) limit of detection and limit of quantification (V) selectivity and specificity

Appl Of Ms Excel In Analytical Chemistry

2nd Edition

ISBN:9781285686691

Author:Crouch

Publisher:Crouch

Chapter4: Least-squares And Calibration Methods

Section: Chapter Questions

Problem 9P

See similar textbooks

Similar questions

3. a. Briefly explain why internal standardization method is useful inanalytical chemistry?b. Why does a response factor of an instrument’s detector need to becalculated?
a- Separation is essential in chemical analysis especially when we are dealing with complexmixture of chemical species. Name 1 separation technique based on basis of operation asbelow. Basis of operation Techniquei) Sizeii) Mass and densityiii) Change in physical state
Discuss and explain the differences that you observe when calibrating with both techniques (AAS and ICP-AES).
prepare an assignment on Application of HPLC in Drug Analysis(Amiloride): one page show name of the drug, dosage form, extraction step, type of column, separation parameters e.g., flow rate, mobile phase, detection wavelength and run time
Mass spectrometry is an extremely versatile detection system for GC. However, interfacing an HPLC system to a mass spectrometer is a much more difficult task. Describe the major reasons why it is more difficult to combine HPLC with mass spectrometry than it is to combine GC with mass spectrometry.
You are developing a Ca detection method for a graphite furnace AA instrument. Your analysis of ten blank samples gives a standard deviation of 0.265 ppb. To establish your limit of detection (LOD), what concentration of Ca should be spiked into your blanks?
Using the absorbance of [FeSCN]+2 at the wavelength of maximum absorption which you obtained in part B, and the diameter of the tube, obtained in part A,calculate the molar extinction coefficient. given info: Concentration of Fe3+ stock solution, C1 = 0.001 M Volume of stock Fe3+ solution pipetted, V1 = 25mL Concentration of diluted stock solution, C2 = 0.0004 M Volume of Fe2+ solution and KSCN (upon mixing) = 10mL Weight of KSCN = 1g The reaction taking place is given as: The reaction taking place is given as: F e 3+ (aq) + SC N − (aq) ⇔Fe [SCN] 2+ (aq) the concentration of [FeSCN]2+ after the mixing of Fe3+ and SCN- is 2.5 x 10-3 M. Moles of [FeSCN]2+ = 2.5 x 10-5 moles Diameter:1.2cm The wavelength at which maximum absorption takes place is = 480 nm
A 0.0200 gram blood sample was decomposed by a microwave digestion technique followed by dilution to 100.0 mL in a volumetric flask. Aliquots of the sample solution were treated with a lead complexing reagent and water as follows: Solution 1: 10.0 ml blood sample + 20.0 mL complexing agent + 30.0 mL H20. Solution 2: 10.0 ml blood sample + 20.0 mL complexing agent + 26.0 mL H20 + 4.00 mL of 78 ppb Pb2+ standard. The resulting solutions were analyzed by UV/Vis at 375 nm. Absorbance for solution 1 = 0.155 and for solution 2 = 0.216. Calculate the concentration of lead (ppb) in the original sample.
In the determination of ethanol concentration in alcoholic beverages using the GCFID method, why do we need to calculate the coefficient variation (CV). standard deviation, repeatability, response factor and response ratio? And how to calculate this parameter?