Two loads P act as shown, one parallel to (x0) and another parallel to z0; each load P equals 1.5 kN. The crankshaft dimensions are b1 = 55 mm, b2 = 150 mm, and b3 = 45 mm. The diameter of the upper shaft is d= 22 mm. Determine the normal stress at point A, which is located on the surface of the upper shaft at the z0 axis. B

Two loads P act as shown, one parallel to (x0) and another parallel to z0; each load P equals 1.5 kN. The crankshaft dimensions are b1 = 55 mm, b2 = 150 mm, and b3 = 45 mm. The diameter of the upper shaft is d= 22 mm. Determine the normal stress at point A, which is located on the surface of the upper shaft at the z0 axis. B

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.5.25P: A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just...

See similar textbooks

Similar questions

The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
A prismatic bar with a length L = 3 ft and cross-sectional area A = 8 in2 is compressed by an axial centroidal load P = 10 kips. Determine the complete state of stress acting on an inclined section pq that is cut through the bar at an angle W = 35", and show the stresses on a properly oriented stress element.
An elevated jogging track is supported at intervals by a wood beam AB (L = 7.5 ft) that is pinned at A and supported by steel rod BC and a steel washer at B. Both the rod (dBC= 3/16 in.) and the washer (dB= 1.0 in.) were designed using a rod tension force of TBC=415 lb. The rod was sized using a factor of safely of 3 against reaching the ultimate stress tru— 60 ksi. An allowable bearing stress sba= 565 psi was used to size the washer at B. A small platform HF is suspended below a section of the elevated track to support some mechanical and electrical equipment. The equipment load is uniform load q = 50 lb/ft and concentrated load WE= 175 lb at mid-span of beam HF. The plan is to drill a hole through beam ABaX £land install the same rod (dBC) and washer) dB) at both D and F to support beam HF. (a) Use s and to check the proposed design for rod DF and washer d,: are they acceptable? (b) Re-check the normal tensile stress in rod BC and bearing stress at 8 if either is inadequate under the additional load from platform HF. Re-design them to meet the original design criteria.
The state of stress on an element along the hydraulic lift cylinder on a truck is trv= — 5 MPaLFind the maximum shear stress on the clement and show the state of stress on a sketch of a properly oriented clement.
A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just snug, then add an additional quarter turn to pre-compress the cast-iron pipe. The pitch of the threads of the bolt ap = 52 mils (a mil is one-thousandth of an inch). Use the numerical properties provided. (a) What stresses a and arwill be produced in the cast-iron pipe and brass rod. respectively, by the additional quarter turn of the nut? (b) Find the bearing stress ahbeneath the washer and the shear stress t(in the steel cap.
Q-1 ) A thin cylinder of inner radius 150 mm and thickness 9 mm is subjected to an internal pressure of 9 MPa. The average circumferential (hoop) stress in MPa is equal to ?
(6) A key is to be designed for a 12.7cm shaft which will transmit power of 150kW @ 360 rpm. If the allowable compressive stress is 1,200kg/cm2, determine: (a) cross-sectional dimensions of the square key to be used; (b) length of the key.
Design a key to transmite 40 kw power by a shaft of 50 mm diameter which rotates 1200 r.p.m , if the permissible shear and crushing stresses are 35 N/mm and 65 N/mm respectively, take the key length 30 mm.
P = 244.8 kips Max sheering stress occurs at 45 deegrees
Compute for the induced compressive stress in kPa, of a steel shafting of 59 mm diameter and 954 m in length that issubjected to an increase of temperature of 88ºC. Use 6.5x10-6/F, E = 30x106 psi.
two solid steel shafts of different diameters are joined together at point C. the diameter of the smaller shaft is 0.5 in, while the diameter of the larger shaft is 1 in. if the supports at both ends, A & B, are unyielding / rigid, and a counterclockwise torque of 500 ft lb at point D, determine the maximum shear stress in the shaft in ksi. The modulus of rigidity for steel is 10800 ksi.Show full solution please
Show whether it is safe by calculating the stresses at point A according to the Tresca Criteria. (Diameter: 20 mm, σA = 320 MPa)