Using the data table given below, calculate the molar concentration for a sample dye solution with a measured absorbance of 0.304. (Hint: Use linear regression analysis.). Final answer in 3 significant figures. Determination of Dye Concentration Solution Dye concentration (mM) Absorbance at 520 1 2.50 0.014 2 5.00 0.176 7.50 0.397 4 10.00 0.611 12.50 0.829

Using the data table given below, calculate the molar concentration for a sample dye solution with a measured absorbance of 0.304. (Hint: Use linear regression analysis.). Final answer in 3 significant figures. Determination of Dye Concentration Solution Dye concentration (mM) Absorbance at 520 1 2.50 0.014 2 5.00 0.176 7.50 0.397 4 10.00 0.611 12.50 0.829

Chemistry & Chemical Reactivity

10th Edition

ISBN:9781337399074

Author:John C. Kotz, Paul M. Treichel, John Townsend, David Treichel

Publisher:John C. Kotz, Paul M. Treichel, John Townsend, David Treichel

Chapter4: Stoichiometry: Quantitative Information About Chemical Reactions

Section: Chapter Questions

Problem 77PS

See similar textbooks

Similar questions

The original solution was diluted by a factor of three, and then the absorbance of the diluted cereal sample solution was measured and recorded as (2.0x10^-1). Use the following trendline and dilution factor to determine the concentration of iron, in unit of M, in the original cereal sample solution. The trendline (linear regression) as displayed on the plot is y = 11898x - 0.0112.
The same chloride analysis but using a new method for which the standard deviation was not known, gave the following replicate results, mean and estimated standard deviation: Chloride (ppm) = 346, 359, 350; Mean = 351.67 ppm; Standard deviation = 6.66ppm. Solve for the CI for the 3 determinations at 95% probability level.
One method for the quantitative determination of the concentration of constituents in a sample analyzed by gas chromatography is area normalization. Here, complete elution of all the sample constituents is necessary. The area of each peak is then measured and corrected for differences in detector response to the different eluates. This correction involves dividing the area by an empirically determined correction factor. The concentration of the analyte is found from the ratio of its corrected area to the total corrected area of all peaks. For a chromatogram containing three peaks, the relative areas were found to be 16.4, 45.2 and 30.2, in order of increasing retention time. Calculate the percentage of each compound if the relative detector responses were 0.60, 0.78 and 0.88, respectively.
What does the %RSD, listed in the spectral data, as well as the correlation coefficient of your standard curve, tell you about the quality of the data and integrity of the results? my standard % RSD is 36.4%, I had to calculate manually from the 5 standard solutions I did have on the spectra. The R squared value from the standard curve is 0.7282
Fluoride determination can be performed photometrically with alizarin red and Zirconium acid solution, obtaining the following data in the calibration: (View Table) 100.0 mL of well water are measured and concentrated to 50 ml by evaporation, the alizarin and zirconium reagents are added (in quantity proportional to the standards) and after the appropriate time, the reading of the instrument (under the same conditions instrumental) reports an absorbance of 0.182. How much fluoride in mg / L does the well water sample contain?
A standard solution was prepared containing 10.0 ppm of an analyte and 15.0 ppm of an internal standard. Analysis of the sample gave signals for the analyte and internal standard of 0.155 and 0.233 (arbitrary units), respectively. Sufficient internal standard was added to an unknown sample to make it 15.0 ppm in the internal standard. Analysis of the unknown sample yielded signals for the analyte and internal standard of 0.274 and 0.198, respectively. Calculate the concentration of analyte in the unknown sample.
Which of the following is TRUE regarding instrumental methods of analysis? A. these methods have lower throughput compared to classical method. B. these methods have lower accuracy compared to classical methods. C. these methods can measure lower analyte concentration than classical methods D. these methods have higher precision compared to classical methods.
One method for quantitative determination of the concentration of constituents in a sample analyzed by gas chromatography is the area normalization method. In this method, complete elution of all of the sample constituents is necessary. The area of each peak is then measured and corrected for differences in detector response to the different eluates. This correction is accomplished by dividing the area by an empirically determined correction factor. The concentration of the analyte is found from the ratio of its corrected area to the total corrected area of all peaks. For a chromatogram containing three peaks, the relative areas were found to be 16.4, 45.2, and 30.2 in the order of increasing retention time. Calculate the percentage of each compound if the relative detector responses were 0.60, 0.78, and 0.88, respectively
FT-IR technique can be utilized for the analysis of unknown analytes by matching it with__________. Both choices are correct Commercial library/database Reference standard
The following data were obtained from a Bradford assay to determine the protein content in a sample: Protein content (μg) Absorbance value 0 0.000 2 0.022 5 0.065 10 0.106 20 0.178 30 0.299 40 0.380 50 0.472 unknown 0.150 a. use excel, another program, or graph paper to produce a calibration curve based on the data. b. Use linear regression (best fit line) to obtain the slope of the line c. Determine the unknown protein content for a sample that shows an absorbance reading of 0.150.
A spectrophotometer method for the quantitative analysis of Pb2+ in blood uses Cu2+ as an internal standard. A standard containing 1.75 ppb Pb2+ and 2.25 ppb Cu2+ yields a signal of 0.832 for Pb2+ and a signal of 0.351 for Cu2+. A sample of blood is spiked with the same concentration of Cu2+, giving a signal of 0.520 for Pb2+ and 0.289 for Cu2+. Determine the concentration of Pb2+ in the sample of blood.
Table 1. Data for the Concentration of the KMnO4 Unknown Solution. Abs of Unknown Solution is 0.362 Absorbance Concentration Trial 1 0.120 0.00145 Trial 2 0.066 0.00104 Unknown Solution: __________ What is the Concentration of the Unknown Solution. _____________ Show statistical treatment of data.