Applied Statics and Strength of Materials (6th Edition)
6th Edition
ISBN: 9780133840728
Author: Limbrunner
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 10, Problem 10.9P
A short, solid, compression member of circular cross section is to support a load of 100 kips. Determine the minimum required diameter for this machine member based on direct, compressive stress. The member is to be made of gray cast iron. Use a factor of safety of 6.0 against compression failure.
Expert Solution & Answer
Learn your wayIncludes step-by-step video
schedule06:13
Students have asked these similar questions
What will be the minimum diameter of a steel wire, which is used to raise a load of 4000N if the stress in the rod is not to exceed 95 MN/m²?
What wall thickness in mm is required for a 634 mm diameter cylinder under an internal pressure of 18 MPa? Use a design stress of 80 MPa?
Do larger members fail at comparatively lower stresses than smaller members?
Chapter 10 Solutions
Applied Statics and Strength of Materials (6th Edition)
Ch. 10 - A 916 - in. - diameter steel rod is tested in...Ch. 10 - A concrete cylinder 150 mm in diameter was tested...Ch. 10 - Prob. 10.3PCh. 10 - The data from the tension test of a steel specimen...Ch. 10 - An 18-in.-long titanium alloy rod is subjected to...Ch. 10 - ASTM A36 steel rods are used to support a balcony....Ch. 10 - A 450-mm-long AISI 1020 steel rod is subjected to...Ch. 10 - A tension member in a roof truss is composed of...Ch. 10 - A short, solid, compression member of circular...Ch. 10 - A main cable in a large bridge is designed for a...
Ch. 10 - Test results of a steel specimen indicated an...Ch. 10 - A concrete canoe in storage is supported by two...Ch. 10 - A load is applied to a rigid bar that is...Ch. 10 - Prob. 10.14CPCh. 10 - Write a program that will allow a user to input...Ch. 10 - A 12 - in. - diaiíct.cr structural nickel steel...Ch. 10 - Compute the modulus of elasticity of a copper...Ch. 10 - A concrete cylinder 6 in. in diameter was tested...Ch. 10 - An aluminum bar 2 in. by 12 - in. in cross section...Ch. 10 - During a tensile test of a steel specimen, the...Ch. 10 - A 12.5-mm-diameter steel rod was subjected to a...Ch. 10 - Prob. 10.22SPCh. 10 - A standard steel specimen having a diameter of...Ch. 10 - 10.24 A tension member in a structure is composed...Ch. 10 - A pair of wire cutters is designed to operate...Ch. 10 - Calculate the end bearing length required for a...Ch. 10 - Design a 3-m-long rod subjected to a tensile load...Ch. 10 - The collar bearing shown is subjected to a...Ch. 10 - A 10-ft-long steel member is subjected to a...Ch. 10 - Two steel bars A and B support a load P, as shown....Ch. 10 - Prob. 10.31SP
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
What parts are included in the vehicle chassis?
Automotive Technology: Principles, Diagnosis, and Service (5th Edition)
What parts are included in the vehicle chassis?
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
If x = 8 m, vx = 8 m/s, and ax = 4 m/s2 when t = 2 s, determine the magnitude of the particles velocity and acc...
Engineering Mechanics: Dynamics (14th Edition)
Replace the two wrenches and the force, acting on the pipe assembly, by an equivalent resultant force and coupl...
Engineering Mechanics: Statics
Comprehension Check 8-5
A 75-gram [g] cylindrical rod is measured to be 10 centimeters [cm] long and 2.5 centim...
Thinking Like an Engineer: An Active Learning Approach (3rd Edition)
1.1 What is the difference between an atom and a molecule? A molecule and a crystal?
Manufacturing Engineering & Technology
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- a short hollow cylindrical steel compression member is required to support an axial load of 180 kN. the material used can carry maximum compressive stress of 95 MPa. Determine the inner and outer diameter of the member if it is 6mm thick and 200mm longarrow_forwardThe steel rod in Fig. is to be used to support an axial load of 18 kip. If Est = 29(103 ) ksi and sY = 50 ksi, determine the smallest diameter of the rod as allowed by the AISC specifications. The rod is fixed at both ends.arrow_forwardFor a rod made of aluminum alloy 2014-T6, select the smallest square cross section that can be used if the rod is to carry a 55-kip centric load.arrow_forward
- Determine the diameter of a brittle member in inches if the tensile design load is 15,671 lb. assuming a factor of safety of 5 based on an ultimate strength of 60,000 psi.arrow_forwardQ // If the value of the highest load we get from the tensile test of a wrought iron model with a circular . section is (52 kN) with an axial stress of ( 460 Mpa), calculate the diameter of the examined modelarrow_forwardA long solid steel bar of uniform 1.25 in diameter has a 0.375 in diameter hole at its center with its axis perpendicular to the length of the shaft. A tensile load of 108,000 lb is applied longitudinally to the bar. Determine the probable material that can be used for this load for a factor of safety of 5arrow_forward
- 13. An airplane’s landing gear must be capable of supporting ⅓ of its weight at 200000 kg. To induce safety, the landing gear must be able to support twice its maximum load. Determine the minimum cross-sectional are (mm2) of the landing gear if it is made of a heat-treated steel having a yield strength of 860 mpa and a tensile strength of 900 mpa.arrow_forwardA hollow, short compression member, of normalized cast steel (ASTM A27-58, 65 ksi), is to support a load of 1500 kips with a factor of safety of 8 based on the ultimate strength. Determine the outside and inside diameters if Do = 2Diarrow_forwarddetermine the diameter of a steel rod that will carry a tensile load of 50000 kg at a stress of 1400 kg per square centimeter.arrow_forward
- The 10-mm-diameter steel bolt is surrounded by a bronze sleeve in (Figure 1). The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. If the yield stress for the steel is (σY)st=680MPa, and for the bronze (σY)br=490MPa, determine the magnitude of the largest elastic load P that can be applied to the assembly. Est=200GPa, Ebr=100GPa. Express your answer to three significant figures and include appropriate units.arrow_forwardA steel rod is to withstand a pull of 10,000 pounds. If the ultimate stress is 50,000 psi and yield stress of 35,000 psi with a factor of safety of 4 and 2 based on ultimate and yield respectively, determine the required diameter of the rod.arrow_forwardA member in tension in a machine frame is subjected to a continuous load of 5.00 kN. Its length is 750 mm and it is made of a carbon steel tube with an outer diameter of 17 mm and an inner diameter of 12 mm. Calculate the tensile stress (in MPa).arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Mechanics of Materials Lecture: Beam Design; Author: UWMC Engineering;https://www.youtube.com/watch?v=-wVs5pvQPm4;License: Standard Youtube License