Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 10, Problem 5ASRQ
While discussing abrasive cleaners: Technician A says that shot is angular in shape and is used for aggressive cleaning. Technician B says that grit is an angularshaped media and is used to peen metal surfaces. Who is correct?
- Technician A
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Chip guard installed between operator and point of operation must be in a specified range is safety precaution for __________________machine.
a.
Lathe
b.
Drilling
c.
Milling machine
d.
Grinding
Explain usefulness of conveyor belt water cleaning machine in avoiding flood.
Cleaning of machine tool should be carried out daily.
Select one:
True
False
Chapter 10 Solutions
Automotive Technology
Ch. 10 - WHat should be worn when working with any type of...Ch. 10 - Why should a memory saver be installed before dis...Ch. 10 - Prob. 1TFCh. 10 - True or False? The first step in removing an...Ch. 10 - Prob. 3TFCh. 10 - What is the best way to lift a vehicle when...Ch. 10 - Prob. 2MCCh. 10 - The buildup of minerals and deposits inside the...Ch. 10 - Hydrocarbon solvents are. flammable toxic both a...Ch. 10 - Which cleaning method uses high-frequency sound...
Ch. 10 - Parts must be when they go into an abrasive blast...Ch. 10 - Prob. 7MCCh. 10 - Which of the following is not considered part of...Ch. 10 - Which of the following statements is not true...Ch. 10 - Which of the following is not a common way to...Ch. 10 - While working on an engine with an excessive...Ch. 10 - While discussing the common causes for cracks...Ch. 10 - Technician A uses a crane to remove an engine from...Ch. 10 - Prob. 4ASRQCh. 10 - While discussing abrasive cleaners: Technician A...Ch. 10 - Technician A labels or marks all electrical wires...Ch. 10 - While discussing cleaning engine parts: Technician...Ch. 10 - While loosening the axle shaft hub nuts on a FWD...Ch. 10 - While preparing to remove an engine: Technician A...Ch. 10 - After removing the vehicles hood in preparation...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Parts must be when they go into an abrasive blast machine. wet dry grease-free both b and carrow_forwardAfter draining gear oil from a transaxie, the technician notices that the oil has shiny, metallic particles in it. What does this indicate?arrow_forwarda) With a neat sketch explain about Induced soft foot.arrow_forward
- WHat should be worn when working with any type of cleaning solvent or chemical?arrow_forwardWhich of the following statements is not true about thermal cleaning? The main advantage of thermal cleaning is a total reduction of all oils and grease on and in blocks, heads, and other parts. After a part has been thermally cleaned, it should be submerged in water to cool it quickly. Thermal cleaning leaves behind a dry, powdery ash on the parts. After a part has been thermally cleaned, it should be washed or blasted with shotarrow_forwardHeavy protective gloves should be worn when. welding grinding metal working with caustic cleaning solutions all of the abovearrow_forward
- A chain saw will run in many positions. Tech a says that this is because of its float type carburetor. Technician b says this is because of its diaphragm type carburetor. Who is correct?arrow_forwardWhat is the difference between scrubber and biofilter?arrow_forwardList down the safety precaution need to carry during the operation of drilling machine?arrow_forward
- Don't give wrong or shortcut solutionarrow_forwardTechnician A says that it is recommended that you wear shoes with nonslip soles in the shop. Technician B says that steel-toed shoes offer the best foot protection. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardList three types of screwdriver tips.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningRefrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage LearningPrecision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
MECH MINUTES | SHAFTS PT. 2: MATERIAL & SURFACE TREATMENT SELECTION | MISUMI USA; Author: MISUMI;https://www.youtube.com/watch?v=jWRA0jhoiRs;License: Standard Youtube License