Air flows in an insulated duct. At point ① the conditions are M1 = 0.1, T1 = − 20° C and p1 = 1.0 MPa absolute. Downstream, at point ②, because of friction the conditions are M2 = 0.7, T2 = − 5.62°C, and p2 = 136.5 kPa absolute. (Four significant figures are given to minimize round off errors.) Compare the stagnation temperatures at points ① and ②, and explain the result. Compute the stagnation pressures at points ① and ②. Can you explain how it can be that the velocity increases for this frictional flow? Should this process be isentropic or not? Justify your answer by computing the change in entropy between points ① and ②. Plot static and stagnation state points on a Ts diagram.
Want to see the full answer?
Check out a sample textbook solutionChapter 12 Solutions
Fox And Mcdonald's Introduction To Fluid Mechanics
Additional Engineering Textbook Solutions
Engineering Mechanics: Statics
Mechanics of Materials (10th Edition)
Fundamentals of Heat and Mass Transfer
Statics and Mechanics of Materials (5th Edition)
Automotive Technology: Principles, Diagnosis, and Service (5th Edition)
Heating Ventilating and Air Conditioning: Analysis and Design
- Gas flowing through a diverging nozzle has at inlet section a temperature of 20 °C, pressure 120 kN/m? and velocity 300 m/s. At the outlet of the nozzle the velocity has fallen to 100 m/s. Assuming an adiabatic flow, what is the values of outlet pressure, temperature, internal energy and specific enthalpy at outlet section. Take y = 1.333 and Cv= 0.86 kJ/kg K.arrow_forwardAs shown in figure Q1, air flows through a converging nozzle from a large tank and into a receiver. At section 1, the temperature is 350 k, the pressure is 320 kPa (abs), and the flow the flow area is 0.40 m?. The pressure in the large tank is 360 kPa (abs). Nozzle exit area is 0.30 m?. Air flow is assumed to be steady and isentropic in the converging nozzle. Express answer at least 3 significant figures. Take K as 1.40 and R as 0.287 kJ/kg.K Determine: a) The mach number at Section 1. b) The mach number, pressure and velocity at the exit. c) The mass flow rate through the nozzle. Large Tank Pressure = 360 kPa (abs) Air flows Nozzle Exitarrow_forwardNozzle is assuming steady one-dimensional flow. M = 2.731. This is the the supersonic flow of air through a convergent-divergent nozzle. The stagnation temperature = 300K, stagnation pressure at the inlet = 107500Pa, static pressure at the exit=4400Pa, C1 is a constant = 0.1097 for calculating circular cross-sectional area of a convergent-divergent nozzle: A = C1 + x^2 and x (axial distance from the throat) =1m. γ = 1.4 and R=287. Calculate the mass flow rate of air through the nozzle. Thank You.arrow_forward
- An industrial nozzle as shown in Figure 3 works with an inert gas rush through the nozzle where the speed of the gas at the nozzle throat is recorded equal to the speed of sound. The inlet velocity, temperature, and pressure are 98 m/s, 600 oC, and 88 psi, respectively.Take the property of inert gas for k = 1.66 and cp = 5.192 kJ/kg. K. Calculate:a) Stagnation pressureb) Mach number at the nozzle inletc) Temperature of the gas at the throatd) Pressure of the gas at the throatarrow_forwardAir flows isentropically through a duct as shown in the figure below. For the conditions shown, find the Mach number at both stations 1 and 2 and the flowrate. The diameter is not necessarily constant. Ma₁ (1) D₁ = 0.15 m V₁ = 40 m/s P1 = 4 atm abs. Ma₁ = Ma₂ = i m₁ = M. kg/s Ma₂ (2 T₂ = 225 K P2 = 2 atm abs.arrow_forwardIn a nozzle, steam enters at T = 673.15 K and P = 800,000 Pa while u = 15m/s. It exits at T = 400,000 Pa and u = 320m/s. What is the ration of the inlet and outlet diameters (D1/D2)?arrow_forward
- 1. At what flow angle will the flow become just sonic downstream of the nozzles of a high pressure turbine? The nozzles discharge into an annulus which has a shroud diameter of 250 mm and hub to the shroud diameter ratio is 0.80. The stagnation pressure and temperature are 1500 kPa and 1277 0 C respectively. The mass flow rate is 7 kg/s. The value of R is 286.96 J/(kg.K) and Cp/ R is 4.1arrow_forwardThe gas entering a rocket nozzle has a stagnation pressure of 1500 kPa and a stagnation temperature of 3300°C. The rocket is traveling in the still Standard Atmosphere at 30,000 m. Find the throat and exit area for a flowrate of 5 kg/s. N.m . The gas is perfectly, expanded kg.K Use the properties of the U.S. Standard Atmosphere. Assume k = 1.35, R = 287.0 F1 to the ambient pressure. At = i Ae= i 2 eTextbook and Media @ Save for Later W X and H -384 #3 E D 80 C m² m² 69 + $ 4 R F F4 % 5 V F5 T G < 6 MacBook Pro B #2 Y H & 7 F7 U N Attempts: 0 of 5 used Submit Answer #00 8 J DII 1 M ( 9 K F9 O ) O V H d F10 , | P 3 V commandarrow_forwardThe jet engine on a test stand, shown in the figure, admitsair at 20oC and 1 atm at section 1, where the area is 0.5 m2and the velocity is 250 m/s. The fuel-to-air ratio is 1:30.The air leaves at section 2 at atmospheric pressure and ahigher temperature. The exit velocity is 900 m/s and thearea is 0.4 m2. Compute the horizontal test stand reactionRx needed to hold the engine fixed.arrow_forward
- a) A convergent-divergent nozzle with a given area ratio is supplied with air at a constant stagnation pressure P, and a constant stagnation temperature To. With the aid of sketches give a clear account of the operation of convergent-divergent nozzles as a function of back pressure P. In your answer clearly indicate the critical points (pressure ratios) along the pressure ratio axis. A rocket is equipped with a convergent-divergent nozzle (== 3.0). b) pare supply temperture and pressure of the Determine the design choked subsonic and supersonic Mach numbers for this area ratio. You may assume the combustion products have the same properties as air and the the nozzle is an ideal nozzle. c) Determine the range of pressure ratios for which a normal shock wave appears in the divergent part of the nozzle. d) At an altitude of 11 km what should be the supply pressure to the nozzle in order to have a fully expanded nozzle. What would be the nozzle's discharge mass flow rate per unit throat…arrow_forwardThe converging-diverging nozzle of the engine of a new supersonic unmanned aerial vehicle (UAV) has an exit area of 50 cm^2 . At the design operating condition, the mass flow rate of exhaust gases (? ≈ 1.4, molecular weight = 26 g/mol) is 1.75 kg/s. The exhaust gases enter the nozzle with stagnation pressure and temperature equal to Po = 300 kPa and To = 500 K, respectively a) What is the optimal cruising altitude for the operation of the nozzle of this UAV? (b) What is the lowest altitude at which the plane can fly such that the flow inside the diverging part of the nozzle is kept supersonic? Note: - Assume that the stagnation conditions of the flow of exhaust gases entering the nozzle are kept constant with varying altitudearrow_forwardCompute stagnation enthalpy of air at normal conditions (P=1atm, T=300K) moving with velocity of 1398 m/s. What temperature of air we will observe?arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY