Consider steady, adiabatic flow of air through a long straight pipe with A = 0.05 m2. At the inlet section ① the air is at 200 kPa absolute, 60°C, and 146 m/s. Downstream at section ②, the air is at 95.6 kPa absolute and 280m/s. Determine
Want to see the full answer?
Check out a sample textbook solutionChapter 12 Solutions
Fox And Mcdonald's Introduction To Fluid Mechanics
Additional Engineering Textbook Solutions
Fundamentals Of Thermodynamics
Thinking Like an Engineer: An Active Learning Approach (4th Edition)
Engineering Mechanics: Statics & Dynamics (14th Edition)
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
Statics and Mechanics of Materials (5th Edition)
INTERNATIONAL EDITION---Engineering Mechanics: Statics, 14th edition (SI unit)
- Steam flows through a nozzle at 400 °C and 1 MPa (h= 263.9 kJ/kg) with velocity of 300 m/s. Find the stagnation enthalpy.arrow_forwardNeed step by step explanationarrow_forward(b) Air flows through a cylindrical duct at a rate of 2.3 kg/s. Friction between air and the duct and friction within air can be neglected. The diameter of the duct is 10cm and the air temperature and pressure at the inlet are T₁ 450 K and P₁ = 200 kPa. If the Mach number at the exit is Ma2 determine the rate of heat transfer and the pressure difference across the duct. The constant pressure specific heat of air is cp = 1.005 kJ/kg-K. The gas constant of air is R = 0.287 kJ/kg-K and assume k = 1.4. -arrow_forward
- Please check attach filearrow_forwardA stream of air at 77°F and 1.2 atm absolute flowing at a rate of 225 ft3/h is blown through ducts that pass through the interior of a large industrial motor. The air emerges at 500°F. Calculate the rate atwhich the air is removing heat generated by the motor. What assumption have you made about the pressure dependence of the specific enthalpy of air?arrow_forwardQ1/ Air enters a compressor at a mass flow rate of 0.04 kg/s with a stagnation pressure of 100 kPa and a stagnation temperature of 400 °C, and it is compressed to a stagnation pressure of 900 kPa. Assuming the compression process to be adiabatic and reversible, find the power required for the compressorarrow_forward
- I need the answer as soon as possiblearrow_forward5. A converging nozzle has an exit area of 56 cm². Nitrogen stored in a reservoir is to be discharged through the nozzle to an ambient pressure of 100 kPa. Determine the flow rate through the nozzle for reservoir pressures of: (a) 120 kPa (b) 140 kPa (c) 200 kPa (d) 1 MPa Assume isentropic nozzle flow. In each case, determine the increase in mass flow to be gained by reducing the back pressure from 100 kPa to 0 kPa. Reservoir temperature is 298 K.arrow_forwardIdeal gas Oxygen (O2) flows through a well-insulated (adiabatic) nozzle. The cross-section of the nozzle is circular and has a diameter of 15 cm at Station 1. Also, at Station 1 the flow has a pressure of 300 kPa, a temperature of 400 Kelvin, and a velocity of 20 m/sec. At Station 2, the temperature is 390 Kelvin. Friction can be neglected. Find the following:arrow_forward
- Steam at a velocity of 60 m/s and 250°C and 7 bar absolute is expanded through a nozzle to 200°C and 5 bar. The nozzle has rigid (non movable) walls and its function is to increase the kinetic energy. Negligible heat is transferred from the nozzle to its surroundings. 1. Calculate the exit stream velocity? 2. Calculate the temperature and quality of the exit steam if it leaves the nozzle at a velocity of 720 m/s and a pressure of 5 bararrow_forwardQ.2. Air flows through a constant-area duct is connected to a reservoir at a temperature of 500°C and a pressure of 500 kPa by a converging nozzle, as shown in Figure. Heat is lost at the rate of 250 kJ /kg. Determine the exit pressure and Mach number and the mass flow rate for a back pressure of 0 kPa. q = 250 kJ/kg Pr = 500 kPa Tr = 500°C Po = 0 kPa D= 0.02marrow_forwardCompute the change in specific entropy when helium, initially at a temper-ature of 273 K and a pressure of 100 kPa, undergoes the following processes: a.An isochoric process with final pressure 250 kPa b.By computing the change in specific entropy, determine whether it is possible foran adiabatic process to bring the gas to a final temperature of 200 K and a densityof 0.3 kg/m3. If not, why not? And if so, how could it be done?arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY