Fox And Mcdonald's Introduction To Fluid Mechanics
9th Edition
ISBN: 9781118921876
Author: Pritchard, Philip J.; Leylegian, John C.; Bhaskaran, Rajesh
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 12, Problem 53P
Steam flows steadily and isentropically through a nozzle. At an upstream section where the speed is negligible, the temperature and pressure are 450°C and 6 MPa absolute. At a section where the nozzle diameter is 2 cm, the steam pressure is 2 MPa absolute. Determine the speed and Mach number at this section and the mass flow rate of steam. Sketch the passage shape.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
(b) Air flows through a cylindrical duct at a rate of 2.3 kg/s. Friction between air and the
duct and friction within air can be neglected. The diameter of the duct is 10cm and the
air temperature and pressure at the inlet are T₁ 450 K and P₁ = 200 kPa. If the Mach
number at the exit is Ma2
determine the rate of heat transfer and the pressure
difference across the duct. The constant pressure specific heat of air is cp = 1.005
kJ/kg-K. The gas constant of air is R = 0.287 kJ/kg-K and assume k = 1.4.
-
Air enters a compressor with negligible velocity
at 85 kPa absolute and 20°C. It leaves with a
velocity of 200 m/s at 600 kPa absolute. For a
mass flux of 5 kg/s, calculate the exit tempera-
ture if the power required is 1500 kW and:
Air enters a diffuser shown in below figure with a speed of 200 m/s.
Determine (a) the speed of sound and (b) the Mach number at the
diffuser inlet when the air temperature is 30°C.
Air
Diffuser
V = 200 m/s
T = 30°C
Chapter 12 Solutions
Fox And Mcdonald's Introduction To Fluid Mechanics
Ch. 12 - Air is expanded in a steady flow process through a...Ch. 12 - Five kilograms of air is cooled in a closed tank...Ch. 12 - Air is contained in a piston-cylinder device. The...Ch. 12 - Calculate the power delivered by the turbine per...Ch. 12 - If hydrogen flows as a perfect gas without...Ch. 12 - A 1-m3 tank contains air at 0.1 MPa absolute and...Ch. 12 - Air enters a turbine in steady flow at 0.5 kg/s...Ch. 12 - Natural gas, with the thermodynamic properties of...Ch. 12 - Carbon dioxide flows at a speed of 10 m/s in a...Ch. 12 - In an isothermal process, 0.1 cubic feet of...
Ch. 12 - Calculate the speed of sound at 20C for (a)...Ch. 12 - An airplane flies at 550 km/hr at 1500 m altitude...Ch. 12 - Actual performance characteristics of the Lockheed...Ch. 12 - For a speed of sound in steel of 4300 m/s,...Ch. 12 - Determine and plot the Mach number of an...Ch. 12 - Investigate the effect of altitude on Mach number...Ch. 12 - The grandstand at the Kennedy Space Center is...Ch. 12 - Use data for specific volume to calculate and plot...Ch. 12 - An object traveling in atmospheric air emits two...Ch. 12 - An object traveling in atmospheric air emits two...Ch. 12 - While at the seashore, you observe an airplane...Ch. 12 - The temperature varies linearly from sea level to...Ch. 12 - Prob. 23PCh. 12 - A photograph of a bullet shows a Mach angle of 32....Ch. 12 - An F-4 aircraft makes a high-speed pass over an...Ch. 12 - All aircraft passes overhead at 3 km altitude. The...Ch. 12 - A supersonic aircraft flies at 3 km altitude at a...Ch. 12 - For the conditions of Problem 12.27, find the...Ch. 12 - The Concorde supersonic transport cruised at M =...Ch. 12 - Plot the percentage discrepancy between the...Ch. 12 - Compute the air density in the undisturbed air and...Ch. 12 - Carbon dioxide flows in a duct at a velocity of 90...Ch. 12 - If nitrogen at 15C is flowing and the stagnation...Ch. 12 - An aircraft cruises at M = 0.65 at 10 km altitude...Ch. 12 - High-speed aircraft use air data computers to...Ch. 12 - A supersonic wind tunnel test section is designed...Ch. 12 - Oxygen flows in a passage at a pressure of 25...Ch. 12 - What is the pressure on the nose of a bullet...Ch. 12 - Prob. 39PCh. 12 - Air flows in an insulated duct. At point the...Ch. 12 - Consider steady, adiabatic flow of air through a...Ch. 12 - Air passes through a normal shock in a supersonic...Ch. 12 - A Boeing 747 cruises at M = 0:87 at an altitude of...Ch. 12 - Space debris impact is a real concern for...Ch. 12 - A CO2 cartridge is used to propel a toy rocket....Ch. 12 - Nitrogen flows from a large tank, through a...Ch. 12 - Air flows from the atmosphere into an evacuated...Ch. 12 - Oxygen discharges from a tank through a convergent...Ch. 12 - The hot gas stream at the turbine inlet of a JT9-D...Ch. 12 - Carbon dioxide discharges from a tank through a...Ch. 12 - Air at 100F and 100 psia in a large tank flows...Ch. 12 - Calculate the required diameter of a convergent...Ch. 12 - Steam flows steadily and isentropically through a...Ch. 12 - Nitrogen flows through a diverging section of duct...Ch. 12 - At a section in a passage, the pressure is 30...Ch. 12 - In a given duct flow M = 2.0; the velocity...Ch. 12 - Air flows isentropically through a converging...Ch. 12 - Five pounds of air per second discharge from a...Ch. 12 - Air flows isentropically through a...Ch. 12 - Air, at an absolute pressure of 60.0 kPa and 27C,...Ch. 12 - Carbon dioxide flows from a tank through a...Ch. 12 - A convergent-divergent nozzle of 50-mm tip...Ch. 12 - Air flows adiabatically through a duct. At the...Ch. 12 - Air flows isentropically through a converging...Ch. 12 - Air flows isentropically through a converging...Ch. 12 - Atmospheric air at 98.5 kPa and 20C is drawn into...Ch. 12 - The exit section of a convergent-divergent nozzle...Ch. 12 - Air flowing isentropically through a converging...Ch. 12 - Air flows from a large tank at p = 650 kPa...Ch. 12 - A converging nozzle is connected to a large tank...Ch. 12 - Air at 0C is contained in a large tank on the...Ch. 12 - A large tank initially is evacuated to 10 kPa...Ch. 12 - Air flows isentropically through a converging...Ch. 12 - Air enters a converging-diverging nozzle at 2 MPa...Ch. 12 - Prob. 75PCh. 12 - A jet transport aircraft, with pressurized cabin,...Ch. 12 - A converging-diverging nozzle, with a throat area...Ch. 12 - Air, at a stagnation pressure of 7.20 MPa absolute...Ch. 12 - A small rocket motor, fueled with hydrogen and...Ch. 12 - Testing of a demolition explosion is to be...Ch. 12 - A total-pressure probe is placed in a supersonic...Ch. 12 - Air flows steadily through a long, insulated...Ch. 12 - Air discharges through a convergent-divergent...Ch. 12 - A normal shock wave exists in an airflow. The...Ch. 12 - Air approaches a normal shock at V1 = 900 m/s, p1...Ch. 12 - Air approaches a normal shock at M1 = 2.5, with...Ch. 12 - Air undergoes a normal shock. Upstream, T1 = 35C,...Ch. 12 - If, through a normal shock wave in air, the...Ch. 12 - The stagnation temperature in an airflow is 149C...Ch. 12 - A supersonic aircraft cruises at M = 2.2 at 12 km...Ch. 12 - The Concorde supersonic transport flew at M = 2.2...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
ICA 8-64
A 3-volt [V] battery delivers a constant current of 100 milliamperes [mA] to the bulb in a flashlight ...
Thinking Like an Engineer: An Active Learning Approach (3rd Edition)
A wet towel hangs on a clothes line under conditions for which one surface receives solar irradiation of Gs=900...
Fundamentals of Heat and Mass Transfer
1.1 What is the difference between an atom and a molecule? A molecule and a crystal?
Manufacturing Engineering & Technology
2.4 Compute the vertical and horizontal components for each of the forces shown.
Applied Statics and Strength of Materials (6th Edition)
Represent each of the following with SI units having an appropriate prefix: (a) 8653 ms, (b) 8368 N, (c) 0.893 ...
Statics and Mechanics of Materials (5th Edition)
The force in each member of truss and the state of members are in tension or compression.
Engineering Mechanics: Statics & Dynamics (14th Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Air is cooled as it flows through a 30-cm-diameter duct. The inlet conditions are Ma1 = 1.2, T01 = 350 K, and P01 = 240 kPa and the exit Mach number is Ma2 = 2.0. Disregarding frictional effects, determine the rate of cooling of air.arrow_forwardConsider air entering a heated duct at p1 = 1 atm and T1 = 288 K. Ignore the effect of friction. Calculate the amount of heat per unit mass (in joules per kilogram) necessary to choke the flow at the exit of the duct for an inlet Mach number of M1 = 2.2.arrow_forwardThe speed of an aircraft is given to be 950 km/h. If the speed of sound at that location is 315 m/s, the Mach number is (a) 0.63 (b) 0.84 (c) 1.0 (d) 1.07 (e) 1.20arrow_forward
- Air enters a diffuser with velocity 289.3m/sec and temperature T₁-300°K and exits with negligible velocity. Assume that air is an ideal gas with Cp=1.004 kJ/kg. Determine the temperature T₁ at the outlet of the diffuser. Provide your answer in Kelvin (K). 1arrow_forwardAn aircraft is designed to cruise at Mach number Ma = 1.1 at 12,000 m where the atmospheric temperature is 236.15 K. Determine the stagnation temperature on the leading edge of the wing.arrow_forwardAir flows isentropically through a duct. At section 1, thepressure and temperature are 250 kPa and 125°C, andthe velocity is 200 m/s. At section 2, the area is 0.25 m2 andthe Mach number is 2.0. Determine (a) Ma1; (b) T2; (c) V2;and (d ) the mass fl ow.arrow_forward
- The Airbus A-340 passenger plane has a maximum takeoff weight of about 260,000 kg, a length of 64 m, a wing span of 60 m, a maximum cruising speed of 945 km/h, a seating capacity of 271 passengers, a maximum cruising altitude of 14,000 m, and a maximum range of 12,000 km. The air temperature at the crusing altitude is about −60°C. Determine the Mach number of this plane for the stated limiting conditions.arrow_forwardOutside air at a temperature of 25°C is drawn into the duct and then heated along the duct at 234 kJ/kg. At section 1 the temperature is T = 15°C and the absolute pressure is 98 kPa. Neglect friction. (Figure 1) Figure 50 mm -2 m- 1 of 1 Determine the Mach number at section 2. Express your answer using three significant figures. M₂ = 0.915 Submit Part B Correct Determine the temperature at section 2. Express your answer using three significant figures. T2₂ = 455 K Submit Part C P₂ Previous Answers Correct Determine the pressure at section 2. Express your answer to three significant figures and include the appropriate units. Submit Previous Answers Value Provide Feedback Units Previous Answers Request Answer ? * Incorrect; Try Again; 5 attempts remainingarrow_forwardTwo war planes travel one above the other at a speed of 3600kmph at two different altitudes. The first one travels at an altitude of 1km above earths surface and the second one travels at an altitude of 11km. The air temperature at 1km altitude is 20°C. The air temperature continuously drops by 6°C for each 1000m altitudes we go up. Determine the Mach number of both aircrafts at their respective altitudes. Assume R = 287 J/kgK; γ=1.4arrow_forward
- Air exits from a reservoir maintained at 15 °C and 400 kPa absolute into a receiver maintained at (a) 200 kPa absolute and (b) 100 kPa absolute. If the exit area is 0.001 m², by using equations determine the mass flow rate.arrow_forwardNitrogen flows from a reservoir in which its velocity is negligible and its temperature is 22°C. The flow is steady and adiabatic. The temperature is Blank 1 K and velocity of Nitrogen gas is Blank 2 meter per second at the point where the Mach number is 2.0. *Express your answers in whole significant figure without decimal value and without unit* Blank 1 Add your answer Blank 2 Add your answerarrow_forwardA high-pressure air reservoir is connected to the inlet of a convergent-divergent nozzle as shown. A normal shock wave forms in the divergent section of the nozzle at the location with an area of 0.35m2. Determine the Mach number at the exit of the nozzle. A, = 0.7 m² Agh = 0.35 m² A = 0.2 m² Po = 1 atm Throat Normal Shock Exitarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Intro to Compressible Flows — Lesson 1; Author: Ansys Learning;https://www.youtube.com/watch?v=OgR6j8TzA5Y;License: Standard Youtube License