PROB & STATS F/ ENGIN & SCI W/ACCESS
9th Edition
ISBN: 9780357007006
Author: DEVORE
Publisher: CENGAGE L
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 12.2, Problem 20E
The bond behavior of reinforcing bars is an important determinant of strength and stability. The article “Experimental Study on the Bond Behavior of Reinforcing Bars Embedded in Concrete Subjected to Lateral Pressure” (J. of Materials in Civil Engr., 2012:125–133) reported the results of one experiment in which varying levels of lateral pressure were applied to 21 concrete cube specimens, each with an embedded 16-mm plain steel round bar. and the corresponding bond capacity was determined. Due to differing concrete cube strengths (fcu, in MPa), the applied lateral pressure was equivalent to a fixed proportion of the specimen’s (0, .1fcu, … , .6fcu). Also, since bond strength can be heavily influenced by the specimen’s fcu, bond capacity was expressed as the ratio of bond strength (MPa) to 
.
| Pressure | 0 | 0 | 0 | .1 | .1 | .1 | .2 |
| Ratio | 0.123 | 0.100 | 0.101 | 0.172 | 0.133 | 0.107 | 0.217 |
| Pressure | .2 | .2 | .3 | .3 | .3 | .4 | .4 |
| Ratio | 0.172 | 0.151 | 0.263 | 0.227 | 0.252 | 0.310 | 0.365 |
| Pressure | .4 | .5 | .5 | .5 | .6 | .6 | .6 |
| Ratio | 0.239 | 0.365 | 0.319 | 0.312 | 0.394 | 0.386 | 0.320 |
- a. Does a
scatterplot of the data support the use of the simple linear regression model? - b. Use the accompanying Minitab output to give point estimates of the slope and intercept of the population regression line.
- c. Calculate a point estimate of the true average bond capacity when lateral pressure is .45fcu.
- d. What is a point estimate of the error standard deviation σ, and how would you interpret it?
- e. What is the value of total variation, and what proportion of it can be explained by the model relationship?
The regression equation is
Ratio = 0.101 + 0.461 Pressure
| Predictor | Coef | SE Coef | T | P |
| Constant | 0.10121 | 0.01308 | 7.74 | 0.000 |
| Pressure | 0.46071 | 0.03627 | 12.70 | 0.000 |
Analysis of Variance
| Source | DF | SS | MS | F | P |
| Regression | 1 | 0.17830 | 0.17830 | 161.37 | 0.000 |
| Residual Error | 19 | 0.02099 | 0.00110 | ||
| Total | 20 | 0.19929 |
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
The article "Change in Creep Behavior of Plexiform Bone with Phosphate Ion Treatment"
(R. Regimbal, C. DePaula, and N. Guzelsu, Bio-Medical Materials and Engineering,
2003:11-25) describes an experiment to study the effects of saline and phosphate ion
solutions on mechanical properties of plexiform bone. The following table presents the
yield stress measurements for six specimens treated with either saline (NaCI) or phosphate
ion (Na,HPO4) solution, at a temperature of either 25°C or 37°C. (The article presents
means and standard deviations only; the values in the table are consistent with these.)
Solution Temperature
NaCl
Yield Stress (MPa)
138.40 130.89 94.646 96.653 116.90 88.215
25°C
NaCl
37°C
92.312 147.28 116.48 88.802 114.37 90.737
Na,HPO,
25°C
120.18 129.43 139.76 132.75 137.23 121.73
Na,HPO4
37°C
123.50 128.94 102.86 99.941 161.68 136.44
a.
Estimate all main effects and interactions.
b. Construct an ANOVA table. You may give ranges for the P-values.
Is the additive model…
The article "Modeling Resilient Modulus and Temperature Correction for Saudi Roads" (H.
Wahhab, I. Asi, and R. Ramadhan, Journal of Materials in Civil Engineering, 2001:298–
305) describes a study designed to predict the resilient modulus of pavement from physical
properties. The following table presents data for the resilient modulus at 40°Cin10® kPa (y),
the surface area of the aggregate in m²/kg (x1), and the softening point of the asphalt in °C
(х).
y
X1
X2
1.48
5.77
60.5
1.70
7.45
74.2
2.03
8.14
67.6
2.86
8.73
70.0
2.43
7.12
64.6
3.06
6.89
65.3
2.44
8.64
66.2
1.29
6.58
64.1
3.53
9.10
68.6
1.04
8.06
58.8
1.88
5.93
63.2
1.90
8.17
62.1
1.76
9.84
68.9
2.82
7.17
72.2
1.00
7.78
54.1
The full quadratic model is y = + P,x, + PzX, + Pz*jXz + Pxx¡ + Bzx; + €. Which
submodel of this full model do you believe is most appropriate? Justify your answer by
fitting two or more models and comparing the results.
The article "Effect of Granular Subbase Thickness on Airfield Pavement Structural
Response" (K. Gopalakrishnan and M. Thompson, Journal of Materials in Civil
Engineering, 2008:331-342) presents a study of the amount of surface deflection caused by
aircraft landing on an airport runway. A load of 160 kN was applied to a runway surface,
and the amount of deflection in mm (y) was measured at various distances in m (x) from the
point of application. The results are presented in the following table.
y
0.000
3.24
0.305
2.36
0.610
1.42
0.914
0.87
1.219
0.54
1.524
0.34
1.830
0.24
a.
Fit the linear model y = Bo + B1x + ɛ. For each coefficient, test the hypothesis that the
coefficient is equal to 0.
b. Fit the quadratic model y = Bo + Bịx + B2x² + ɛ. For each coefficient, test the hypothesis
that the coefficient is equal to 0.
%3D
Fit the cubic model y = Bo + B1x +
B2x? + B3x + E. For each coefficient, test the
C.
hypothesis that the coefficient is equal to 0.
d.
Which of the models in parts (a)…
Chapter 12 Solutions
PROB & STATS F/ ENGIN & SCI W/ACCESS
Ch. 12.1 - The efficiency ratio for a steel specimen immersed...Ch. 12.1 - The article Exhaust Emissions from Four-Stroke...Ch. 12.1 - Bivariate data often arises from the use of two...Ch. 12.1 - The accompanying data on y = ammonium...Ch. 12.1 - The article Objective Measurement of the...Ch. 12.1 - One factor in the development of tennis elbow, a...Ch. 12.1 - The article Some Field Experience in the Use of an...Ch. 12.1 - Referring to Exercise 7, suppose that the standard...Ch. 12.1 - The flow rate y (m3/min) in a device used for...Ch. 12.1 - Suppose the expected cost of a production run is...
Ch. 12.1 - Suppose that in a certain chemical process the...Ch. 12.2 - Refer back to the data in Exercise 4, in which y =...Ch. 12.2 - The accompanying data on y = ammonium...Ch. 12.2 - Refer to the lank temperature-efficiency ratio...Ch. 12.2 - Values of modulus of elasticity (MOE, the ratio of...Ch. 12.2 - The article Characterization of Highway Runoff in...Ch. 12.2 - For the past decade, rubber powder has been used...Ch. 12.2 - For the past decade, rubber powder has been used...Ch. 12.2 - The following data is representative of that...Ch. 12.2 - The bond behavior of reinforcing bars is an...Ch. 12.2 - Wrinkle recovery angle and tensile strength are...Ch. 12.2 - Calcium phosphate cement is gaining increasing...Ch. 12.2 - a. Obtain SSE for the data in Exercise 19 from the...Ch. 12.2 - The invasive diatom species Didymosphenia geminata...Ch. 12.2 - Prob. 25ECh. 12.2 - Show that the point of averages (x,y) lies on the...Ch. 12.2 - Prob. 27ECh. 12.2 - a. Consider the data in Exercise 20. Suppose that...Ch. 12.2 - Consider the following three data sets, in which...Ch. 12.3 - Reconsider the situation described in Exercise 7,...Ch. 12.3 - During oil drilling operations, components of the...Ch. 12.3 - Exercise 16 of Section 12.2 gave data on x =...Ch. 12.3 - During oil drilling operations, components of the...Ch. 12.3 - For the past decade, rubber powder has been used...Ch. 12.3 - Refer back to the data in Exercise 4, in which y =...Ch. 12.3 - Misi (airborne droplets or aerosols) is generated...Ch. 12.3 - Prob. 37ECh. 12.3 - Refer to the data on x = liberation rate and y =...Ch. 12.3 - Carry out the model utility test using the ANOVA...Ch. 12.3 - Prob. 40ECh. 12.3 - Prob. 41ECh. 12.3 - Verify that if each xi is multiplied by a positive...Ch. 12.3 - Prob. 43ECh. 12.4 - Fitting the simple linear regression model to the...Ch. 12.4 - Reconsider the filtration ratemoisture content...Ch. 12.4 - Astringency is the quality in a wine that makes...Ch. 12.4 - The simple linear regression model provides a very...Ch. 12.4 - Prob. 48ECh. 12.4 - You are told that a 95% CI for expected lead...Ch. 12.4 - Prob. 50ECh. 12.4 - Refer to Example 12.12 in which x = test track...Ch. 12.4 - Plasma etching is essential to the fine-line...Ch. 12.4 - Consider the following four intervals based on the...Ch. 12.4 - The height of a patient is useful for a variety of...Ch. 12.4 - Prob. 55ECh. 12.4 - The article Bone Density and Insertion Torque as...Ch. 12.5 - The article Behavioural Effects of Mobile...Ch. 12.5 - The Turbine Oil Oxidation Test (TOST) and the...Ch. 12.5 - Toughness and fibrousness of asparagus are major...Ch. 12.5 - Head movement evaluations are important because...Ch. 12.5 - Prob. 61ECh. 12.5 - Prob. 62ECh. 12.5 - Prob. 63ECh. 12.5 - The accompanying data on x = UV transparency index...Ch. 12.5 - Torsion during hip external rotation and extension...Ch. 12.5 - Prob. 66ECh. 12.5 - Prob. 67ECh. 12 - The appraisal of a warehouse can appear...Ch. 12 - Prob. 69SECh. 12 - Forensic scientists are often interested in making...Ch. 12 - Phenolic compounds are found in the effluents of...Ch. 12 - The SAS output at the bottom of this page is based...Ch. 12 - The presence of hard alloy carbides in high...Ch. 12 - The accompanying data was read from a scatterplot...Ch. 12 - An investigation was carried out to study the...Ch. 12 - Prob. 76SECh. 12 - Open water oil spills can wreak terrible...Ch. 12 - In Section 12.4, we presented a formula for...Ch. 12 - Show that SSE=Syy1Sxy, which gives an alternative...Ch. 12 - Suppose that x and y are positive variables and...Ch. 12 - Let sx and sy denote the sample standard...Ch. 12 - Verify that the t statistic for testing H0: 1 = 0...Ch. 12 - Use the formula for computing SSE to verify that...Ch. 12 - In biofiltration of wastewater, air discharged...Ch. 12 - Normal hatchery processes in aquaculture...Ch. 12 - Prob. 86SECh. 12 - Prob. 87SE
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, statistics and related others by exploring similar questions and additional content below.Similar questions
- The article "Effect of Granular Subbase Thickness on Airfield Pavement Structural Response" (K. Gopalakrishnan and M. Thompson, Journal of Materials in Civil Engineering, 2008:331-342) presents a study of the effect of the subbase thickness (in mm) on the amount of surface deflection caused by aircraft landing on an airport runway. Two landing gears, one simulating a Boeing 747 aircraft, and the other a Boeing 777 aircraft, were trafficked across four test sections of runway. The results are presented in the following table. Section 3 4 Boeing 747 Boeing 777 4.01 3.87 3.72 3.76 4.57 4.48 4.36 4.43 Can you conclude that the mean deflection is greater for the Boeing 777?arrow_forwardThe article “Effect of Granular Subbase Thickness on Airfield Pavement Structural Response” (K. Gopalakrishnan and M. Thompson, Journal of Materials in Civil Engineering, 2008:331–342) presents a study of the effect of the subbase thickness on the amount of surface deflection caused by aircraft landing on an airport runway. In six applications of a 160 kN load on a runway with a subbase thickness of 864 mm, the average surface deflection was 2.03 mm with a standard deviation of 0.090 mm. Find a 90% confidence interval for the mean deflection caused by a 160 kN load.arrow_forwardThe article "Influence of Freezing Temperature on Hydraulic Conductivity of Silty Clay" (J. Konrad and M. Samson, Journal of Geotechnical and Geoenvironmental Engineering, 2000:180–187) describes a study of factors affecting hydraulic conductivity of soils. The measurements of hydraulic conductivity in units of 108 cm/s (y), initial void ratio (x), and thawed void ratio (x2) for 12 specimens of silty clay are presented in the following table. y 1.01 1.12 1.04 1.30 1.01 1.04 0.955 1.15 1.23 1.28 1.23 1.30 0.84 0.88 0.85 0.95 0.88 0.86 0.85 0.89 0.90 0.94 0.88 0.90 X1 0.81 0.85 0.87 0.92 0.84 0.85 0.85 0.86 0.85 0.92 0.88 0.92 X2 Fit the model y = Bo + fix1 + e. For each coefficient, test the null hypothesis that it is equal to 0. Fit the model y = Bo + Bzx2 + e. For each coefficient, test the null hypothesis that it is equal to 0. Fit the model y = Bo + BzX1 + Bzxz + e. For each coefficient, test the null hypothesis that it is equal to 0. d. Which of the models in parts (a) to (c) is…arrow_forward
- The article "Gypsum Effect on the Aggregate Size and Geometry of Three Sodic Soils Under Reclamation" (I. Lebron, D. Suarez, and T. Yoshida, Journal of the Soil Science Society of America, 2002:92-98) reports on an experiment in which gypsum was added in various amounts to soil samples before leaching. One of the outcomes of interest was the pH of the soil. Gypsum was added in four different amounts. Three soil samples received each amount added. The pH measurements of the samples are presented in the following table. Gypsum (g/kg) pH 0.00 7.88 7.72 7.68 0.11 7.81 7.64 7.85 0.19 7.84 7.63 7.87 0.38 7.80 7.73 8.00 Can you conclude that the pH differs with the amount of gypsum added? Provide the value of the test statistic and the P-value.arrow_forwardArtificial joints consist of a ceramic ball mounted on a taper. The article "Friction in Orthopaedic Zirconia Taper Assemblies" (W. Macdonald, A. Áspenberg, et al., Proceedings of the Institution of Mechanical Engineers, 2000: 685-692) presents data on the coefficient of friction for a push-on load of 2 kN for taper assemblies made from two zirconium alloys and employing three different neck lengths. Five measurements were made for each combination of material and neck length. The results presented in the following table are consistent with the cell means and standard deviations presented in the article. Тарег Material Neck Length Coefficient of Friction CPTI-ZIO2 CPTI-Z:O, CPTI-Z:O, Long TIAlloy-ZrO, Short TiAlloy-ZrO, Medium TiAlloy-ZrO, Long Short 0.254 0.195 0.281 0.289 0.220 Medium 0.196 0.220 0.185 0.259 0.197 0.329 0.481 0.320 0.296 0.178 0.150 0.118 0.158 0.175 0.131 0.180 0.184 0.154 0.156 0.177 0.178 0.198 0.201 0.199 0.210 Compute the main effects and interactions. Construct…arrow_forwardThe article “Some Parameters of the Population Biology of Spotted Flounder (Ciutharuslinguatula Linnaeus, 1758) in Edremit Bay (North Aegean Sea)” (D. Türker, B. Bayhan, etal., Turkish Journal of Veterinary and Animal Science, 2005:1013–1018) models therelationship between weight W and length L of spotted flounder as W = aLb where a and bare constants to be estimated from data. Transform this equation to produce a linear model.arrow_forward
- Please show me your solutions and interpretations. Show the completehypothesis-testing procedure.An article in the ASCE Journal of Energy Engineering (1999, Vol. 125, pp. 59–75) describes a study of the thermal inertia properties of autoclaved aerated concrete used as a building material. Five samples of the material were tested in a structure, and the average interior temperatures (°C) reported were as follows: 23.01, 22.22, 22.04, 22.62, and 22.59. Test that the average interior temperature is equal to 22.5 °C using α = 0.05.arrow_forwardThe article " The Ball-on-Three-Ball Test for Tensile Strength: Refined Methodology and Results for Three Hohokam Ceramic Types" (M. Beck, American Antiquity, 2002:558-569) discusses the strength of ancient ceramics. Several specimens of each of three types of ceramic were tested. The loads (in kg) required to caack the specimens are as follows: Ceramic Loads (kg) Type Sacaton 15, 30, 51, 20, 17, 19, 20, 32, 17, 15, 23, 19, 15, 18, 16, 22, 29, 15, 13, 15 27, 18, 28, 25, 55, 21, 18, 34, 23, 30, 20, 30, 31, 25, 28, 26, 17, 19, 16, 24, 19, 9, 31, 19, 27, 20, 43, 15 20, 16, 20, 36, 27, 35, 66, 15, 18, 24, 21, 30, 20, 24, Gila Plain Casa Grande 23, 21, 13, 21 Construct comparative boxplots for the three samples. b. How many outliers does each sample contain? c Comment on the features of the three samples.arrow_forwardA study was carried out to compare the writing lifetimes of four premium brands of pens. It was thought that the writing surface might affect life- time, so three different surfaces were randomly se- tected. A writing machine was used to ensure that conditions were otherwise homogeneous (e.g., con- stant pressure and a fixed angle). The accompany- ing table shows the two lifetimes (min) obtained for each brand-surface combination. In addition, EEEr = 11,499,492 and EExj, = 22,982,552, Writing Surface 1 2 3 1 709, 659 713, 726 660, 643 Brand 2 668, 685 722, 740 692, 720 of Pen 3 659, 685 666, 684 678, 750 4 698, 650 704, 666 686, 733 4112 4227 4122 4137 5413 5621 5564 16,598 Carry out an appropriate ANOVA, and state your conclusions.arrow_forward
- The article "Permeability, Diffusion and Solubility of Gases" (B. Flaconnèche, et al., Oil and Gas Science and Technology, 2001:262–278) reported on a study of the effect of temperature and other factors on gas transport coefficients in semicrystalline polymers. The permeability coefficient (in 10-6 cm³ (STP) / cm · s· MPa) of CO, was measured for extruded medium-density polyethylene at both 60°C and 61°C. The results are as follows: 60°C: 54 51 61 67 57 69 60 60 63 62 61°C: 58 60 66 66 68 61 60 Find a 95% confidence interval for the difference in the permeability coefficent between 60°C and 61°C.arrow_forwardThe article "Effect of Microstructure and Weathering on the Strength Anisotropy of Porous Rhyolite" (Y. Matsukura, K. Hashizume, and C. Oguchi, Engineering Geology, 2002:39- 17) investigates the relationship between the angle betwween cleavage and flow structure and the strength of porous rhyolite. Strengths (in MPa) were measured for a mumber of specimens cut at various angles. The mean and standard deviation of the strengths for each angle are presented in the following table. Angle Mean 0° 22.9 Sample Size Standard Deviation 2.98 12 15° 22.9 1.16 30° 19.7 3.00 45° 14.9 2.99 60° 13.5 2.33 75° 11.9 2.10 90 14.3 3.95 6. Can you conclude that strength varies with the angle?arrow_forwardAdding glass particles to clay brick may improve the structural properties of the brick. The article "Effects of Waste Glass Additions on the Properties and Durability of Fired Clay Brick" (S. Chidiac and L. Federico, Can J Civ Eng, 2007:1458–1466) describes experiments in which the compressive strength (in MPa) was measured for bricks with varying amounts of glass content and glass particle size. The results in the following table are consistent with means and standard deviations presented in the article. Glass Content (%) Strength (MPa) Size 5 Coarse 78.7 70.8 78.6 81.7 79.2 5 Fine 73.0 90.1 71.4 93.8 82.7 10 Coarse 80.1 76.9 76.5 84.3 77.7 10 Fine 76.2 80.1 121.2 81.4 61.2 15 Coarse 90.3 95.8 103.1 99.5 73.3 15 Fine 141.1 144.1 122.4 134.5 124.9 a. Estimate all main effects and interactions. b. Construct an ANOVA table. You may give ranges for the P-values. Is the additive model plausible? Provide the value of a test statistic and the P-value. Can the effect of glass content on…arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
MATLAB: An Introduction with ApplicationsStatisticsISBN:9781119256830Author:Amos GilatPublisher:John Wiley & Sons Inc
Probability and Statistics for Engineering and th...StatisticsISBN:9781305251809Author:Jay L. DevorePublisher:Cengage Learning
Statistics for The Behavioral Sciences (MindTap C...StatisticsISBN:9781305504912Author:Frederick J Gravetter, Larry B. WallnauPublisher:Cengage Learning
Elementary Statistics: Picturing the World (7th E...StatisticsISBN:9780134683416Author:Ron Larson, Betsy FarberPublisher:PEARSON
The Basic Practice of StatisticsStatisticsISBN:9781319042578Author:David S. Moore, William I. Notz, Michael A. FlignerPublisher:W. H. Freeman
Introduction to the Practice of StatisticsStatisticsISBN:9781319013387Author:David S. Moore, George P. McCabe, Bruce A. CraigPublisher:W. H. Freeman
MATLAB: An Introduction with Applications
Statistics
ISBN:9781119256830
Author:Amos Gilat
Publisher:John Wiley & Sons Inc
Probability and Statistics for Engineering and th...
Statistics
ISBN:9781305251809
Author:Jay L. Devore
Publisher:Cengage Learning
Statistics for The Behavioral Sciences (MindTap C...
Statistics
ISBN:9781305504912
Author:Frederick J Gravetter, Larry B. Wallnau
Publisher:Cengage Learning
Elementary Statistics: Picturing the World (7th E...
Statistics
ISBN:9780134683416
Author:Ron Larson, Betsy Farber
Publisher:PEARSON
The Basic Practice of Statistics
Statistics
ISBN:9781319042578
Author:David S. Moore, William I. Notz, Michael A. Fligner
Publisher:W. H. Freeman
Introduction to the Practice of Statistics
Statistics
ISBN:9781319013387
Author:David S. Moore, George P. McCabe, Bruce A. Craig
Publisher:W. H. Freeman
Hypothesis Testing using Confidence Interval Approach; Author: BUM2413 Applied Statistics UMP;https://www.youtube.com/watch?v=Hq1l3e9pLyY;License: Standard YouTube License, CC-BY
Hypothesis Testing - Difference of Two Means - Student's -Distribution & Normal Distribution; Author: The Organic Chemistry Tutor;https://www.youtube.com/watch?v=UcZwyzwWU7o;License: Standard Youtube License