Loose Leaf for Shigley's Mechanical Engineering Design Format: LooseLeaf
10th Edition
ISBN: 9780073399652
Author: BUDYNAS
Publisher: Mcgraw Hill Publishers
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 13, Problem 27P
In the reverted planetary train illustrated, find the speed and direction of rotation of the arm if gear 2 is unable to rotate and gear 6 is driven at 12 rev/min in the clockwise direction as viewed from the bottom of the figure.
Problem 13-27
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Two mating involute spur gear of 20° pressure angle have a gear ratio of 2. The number of teeth on the pinion is 20 and its speed is 250 r.p.m. The module pitch of the teeth is 12 mm. If the addendum on each wheel is such that the path of approach and the path of recess on each side are half the maximum possible length, find : a. The addendum for pinion and gear wheel; b. The length of the arc of contact; c. The maximum velocity of sliding during approach and recess. Assume pinion to be the driver.
A compound epicyclic gear is shown in Fig. for Q.2. C and D form acompound wheel which rotates freely on shaft G. The planet wheels B andE rotate on pins fixed in arms attached to shaft G. C and F have internalteeth: the others have external teeth with the following numbers: A, 40;B, 30; D, 50; E, 20. If A rotates at 500 rev/min and wheel F is fixed,find the speed of shaft G.
A synchronous belt drive system is used as a speed reducer. The input shaft rotates at 1000 rpm and has a 36-tooth sprocket with a pitch diameter of 3.609 in. The output shaft has a 72-tooth sprocket with a pitch diameter of 7.218 in. the center distance between the two shafts is 15.01 in. Determine the following for the belt drive:
a. The velocity ratiob. The angular velocity of the output shaftc. The linear belt speedd. The belt wrap on the input and output sprocketse. The belt perimeter lengthf. Draw the schematic of the belt drive system
Chapter 13 Solutions
Loose Leaf for Shigley's Mechanical Engineering Design Format: LooseLeaf
Ch. 13 - A 17-tooth spur pinion has a diametral pitch of 8...Ch. 13 - A 15-tooth spur pinion has a module of 3 mm and...Ch. 13 - A spur gearset has a module of 6 mm and a velocity...Ch. 13 - A 21-tooth spur pinion mates with a 28-tooth gear....Ch. 13 - A 20 straight-tooth bevel pinion having 14 teeth...Ch. 13 - A parallel helical gearset uses a 20-tooth pinion...Ch. 13 - A parallel helical gearset consists of a 19-tooth...Ch. 13 - To avoid the problem of interference in a pair of...Ch. 13 - Prob. 9PCh. 13 - Prob. 10P
Ch. 13 - Prob. 11PCh. 13 - Prob. 12PCh. 13 - Prob. 13PCh. 13 - Prob. 14PCh. 13 - A parallel-shaft gearset consists of an 18-tooth...Ch. 13 - The double-reduction helical gearset shown in the...Ch. 13 - Shaft a in the figure rotates at 600 rev/min in...Ch. 13 - The mechanism train shown consists of an...Ch. 13 - The figure shows a gear train consisting of a pair...Ch. 13 - A compound reverted gear trains are to be designed...Ch. 13 - Prob. 21PCh. 13 - Prob. 22PCh. 13 - Prob. 23PCh. 13 - A gearbox is to be designed with a compound...Ch. 13 - The tooth numbers for the automotive differential...Ch. 13 - Prob. 26PCh. 13 - In the reverted planetary train illustrated, find...Ch. 13 - Prob. 28PCh. 13 - Tooth numbers for the gear train shown in the...Ch. 13 - The tooth numbers for the gear train illustrated...Ch. 13 - Shaft a in the figure has a power input of 75 kW...Ch. 13 - The 24T 6-pitch 20 pinion 2 shown in the figure...Ch. 13 - The gears shown in the figure have a module of 12...Ch. 13 - The figure shows a pair of shaft-mounted spur...Ch. 13 - Prob. 35PCh. 13 - Prob. 36PCh. 13 - A speed-reducer gearbox containing a compound...Ch. 13 - For the countershaft in Prob. 3-72, p. 152, assume...Ch. 13 - Prob. 39PCh. 13 - Prob. 40PCh. 13 - Prob. 41PCh. 13 - Prob. 42PCh. 13 - The figure shows a 16T 20 straight bevel pinion...Ch. 13 - The figure shows a 10 diametral pitch 18-tooth 20...Ch. 13 - Prob. 45PCh. 13 - The gears shown in the figure have a normal...Ch. 13 - Prob. 47PCh. 13 - Prob. 48PCh. 13 - Prob. 49PCh. 13 - The figure shows a double-reduction helical...Ch. 13 - A right-hand single-tooth hardened-steel (hardness...Ch. 13 - The hub diameter and projection for the gear of...Ch. 13 - A 2-tooth left-hand worm transmits 34 hp at 600...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Shaft "a" in the figure rotates at 450 rev/min in the direction shown. Find the speed and direction of rotation of shaft "d".arrow_forwardA commercial quadrotor drone for the photography industry uses a propellersystem that uses gears. The 20-tooth spur pinion with a diametrical pitch of8 rotates 2000 rpm and drives a spur gear that rotates the blades. Determinethe theoretical centre distance, the number of teeth on the gear and circularpitch.arrow_forwardQ) Two mating gears have 20 and 40 involute teeth of module 10 mm and 20° pressure angle. If the addendum on each wheel is such that the path of contact is maximum and interference are just avoided, find the addendum of the wheel?arrow_forward
- An epicyclic gear consists of ring gear, planet gear and sun gear. The ring has 72 internal teeth and sun gear has 32 external teeth . Planet gear meshes with both ring and sun gears and carried an arm which rotates about the centre of the ring gear at 20 r.p.m . If the gear A is fixed. Calculate the speed of planet gear.arrow_forwardFor the gear train illustrated in Figure, determine the output speed and direction of rotation if the input shaft rotates at 1490 rpm clockwise. Gears A to D have a module of 1.5 and gears E to H a module of 2. TA=20 teeth, TD=38 teeth, TE=18 teeth, TG=18 teeth, TH=30 teeth, dB=67.5mm, dC=27 mm and dF =56 mm.arrow_forwardQ5 Determine the output rotational speed, ω2 for the gear train shown in Figure Q5 if ω1 = 200 rpm CW. N1 = 20; N3 = 25, N4 = 70, N5 = 15, N6 = 15, N7 = 35, N8 = 80.arrow_forward
- The figure shows a double-reduction helical gearset. Pinion 2 is the driver, and it receives a torque of 1200 Ibf • in from its shaft in the direction shown. Pinion 2 has a normal diametral pitch of 8 teeth/in, 14 teeth, and a normal pressure angle of 20° and is cut right-handed with a helix angle of 30°. The mating gear 3 on shaft b has 36 teeth. Gear 4, which is the driver for the second pair of gears in the train, has a normal diametral pitch of 3 teeth/in, 15 teeth, and a normal pressure angle of 20° and is cut left-handed with a helix angle of 15°. Mating gear S has 45 teeth. Find the magnitude and direction of the force exerted by the bearings C and D on shaft b if bearing C can take only a radial load while bearing D is mounted to take both radial and thrust loads.arrow_forwardpinion having 20 involute teeth of module pitch 6 mm rotates at 200 r.p.m. and transmits 1.5 kW to a gear wheel having 50 teeth. The addendum on both the wheels is 1/4 of the circular pitch. The angle of obliquity is 20°. Find (a) the length of the path of approach ; (b) the length of the arc of approach; (c) the normal force between the teeth at an instant where there is only pair of teeth in contact.arrow_forwardA simple gear train of 30 and 50 teeth for pinion and gear wheel respectively, is used to drive an electric wheelchair at a velocity that is double the maximum velocity of slip. The pinion has an equal addendum as the gear wheel, a module of 3 mm, and a pressure angle of 14.5o. The wheelchair has a maximum velocity of 5 m/s when its pinion rotates at 800 r.p.m. Calculate The maximum length of a path of the approach in mm.arrow_forward
- The figure below shows a two-stage helical gear set. Pinion 2, which is in the converter position, transfers a certain rotation moment from the shaft to gear 3 in the first stage by rotating in the direction of the clock in the front view (or in the Z direction) shown in the figure. on shaft B, the pinion gear No. 4 is positioned with gear No. 3, which receives and/or transmits the drive from different gears. The number 4 Pinion in the second stage drives the number 5 gear, converting the input moment in the system to the output moment and providing movement transfer. Answer the figure in the table as follows by determining the direction of rotation of Gears 3, 4 and 5 and the Helix direction of each gear when looking at the left side view of the figure from the left (i.e. from the-z direction).arrow_forwardThe figure below shows a two-stage helical gear set. Pinion 2, which is in the converter position, transfers a certain rotation moment from the shaft to gear 3 in the first stage by rotating in the direction of the clock in the front view (or in the Z direction) shown in the figure. on shaft B, the pinion gear No. 4 is positioned with gear No. 3, which receives and/or transmits the drive from different gears. The number 4 Pinion in the second stage drives the number 5 gear, converting the input moment in the system to the output moment and providing movement transfer. Answer the figure in the table as follows by determining the direction of rotation of Gears 3, 4 and 5 and the Helix direction of each gear when looking at the left side view of the figure from the left (i.e. from the-z direction).Also, briefly explain how the concept of a module in Gears is determined by showing the basic dimensions on a tooth form and what the main law of gears refers to by drawing a figure.arrow_forwardProvide very clear and complete solution and diagam. SITUATIONAL PROBLEM: Two shafts are connected by spur gears. The pitch radii of the gears A and B are 200 mm and 860 mm respectively. If shaft A makes 350rpm and is subjected to twisting moment of 250 N-m. Pressure angle is 14.5 degree. What is: a.) Rpm of gear B b.) Torque in shaft B (in Newton meter). c.) Separation load of two gears (in newtons). d.) Total load on gears (in newtons).arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Power Transmission; Author: Terry Brown Mechanical Engineering;https://www.youtube.com/watch?v=YVm4LNVp1vA;License: Standard Youtube License