A hand—driven tire pump has a piston with a 2.50−cm diameter and a maximum stroke of 30.0 cm. (a) How much work do you do in one stroke if the average gauge pressure is
Want to see the full answer?
Check out a sample textbook solutionChapter 15 Solutions
College Physics For Ap® Courses
Additional Science Textbook Solutions
Physics: Principles with Applications
University Physics with Modern Physics (14th Edition)
Physics for Scientists and Engineers: A Strategic Approach with Modern Physics (4th Edition)
College Physics: A Strategic Approach (4th Edition)
Essential University Physics: Volume 2 (3rd Edition)
- A cylinder that has a 40.0-cm radius and is 50.0 cm deep is filled with air at 20.0C and 1.00 atm (Fig. P10.74a). A 20.0-kg piston is now lowered into the cylinder, compressing the air trapped inside as it takes equilibrium height hi (Fig. P16.74b). Finally, a 25.0-kg dog stands on the piston, further compressing the air, which remains at 20C (Fig. P16.74c). (a) How far down (h) does the piston move when the dog steps onto it? (b) To what temperature should the gas be warmed to raise the piston and dog back to hi?arrow_forwardA vertical cylinder of cross-sectional area A is fitted with a tight-fitting, frictionless piston of mass m (Fig. P16.56). The piston is not restricted in its motion in any way and is supported by the gas at pressure P below it. Atmospheric pressure is P0. We wish to find die height h in Figure P16.56. (a) What analysis model is appropriate to describe the piston? (b) Write an appropriate force equation for the piston from this analysis model in terms of P, P0, m, A, and g. (c) Suppose n moles of an ideal gas are in the cylinder at a temperature of T. Substitute for P in your answer to part (b) to find the height h of the piston above the bottom of the cylinder.arrow_forwardConsider these scenarios and state whether work is done by the system on the environment (SE) or by the environment on the system (ES): (a) opening a carbonated beverage; (b) filling a flat tire; (c) a sealed empty gas can expands on a hot day, bowing out the walls.arrow_forward
- Consider the piston cylinder apparatus shown in Figure P20.81. The bottom of the cylinder contains 2.00 kg of water at just under 100.0c. The cylinder has a radius of r = 7.50 cm. The piston of mass m = 3.00 kg sits on the surface of the water. An electric heater in the cylinder base transfers energy into the water at a rate of 100 W. Assume the cylinder is much taller than shown in the figure, so we dont need to be concerned about the piston reaching the top of the cylinder. (a) Once the water begins boiling, how fast is the piston rising? Model the steam as an ideal gas. (b) After the water has completely turned to steam and the heater continues to transfer energy to the steam at the same rate, how fast is the piston rising?arrow_forwardA hand-driven tire pump has a piston with a 3.00 cm diameter and a maximum stroke of 25.0 cm. (a) How much work (in J) do you do in one stroke if the average gauge pressure is 2.40 ✕ 105 N/m2 (about 35 psi)? J (b) What average force (in N) do you exert on the piston, neglecting friction and gravity? Narrow_forward10 نقاط A certain fluid at 10 bar is contained in a cylinder behind a piston, the initial volume being 0.05m^3. Calculate the work done by the fluid when it expands reversibly according to a law pv^3=c to a final * .volume of 0.06m^3 W=15.638 KJ O W=6.638 KJ O W=10.34 KJ O W=7.638 KJarrow_forward
- When a .22-caliber rifle is fired, the expanding gas from the burning gunpowder creates a pressure behind the bullet. This pressure causes the force that pushes the bullet through the barrel. Suppose the barrel has a length of 0.633 m and an opening whose radius is 2.67 x 10-3 m. A bullet (mass = 2.6 x 10-3 kg) has a speed of 348 m/s after passing through this barrel. Ignore friction and determine the average pressure of the expanding gas.arrow_forwardA cylinder contains one liter of air at room temperature (300 K) and atmospheric pressure (105 N/m2). At one end of the cylinder is a massless piston, whose surface area is 0.01 m2 . Suppose that you push the piston in very suddenly, exerting a force of 2000 N. The piston moves only one millimeter, before it is stopped by an immovable barrier of some sort. How much work have you done on this system?arrow_forwardWater at 15°C is to be pumped from a reservoir (zA = 2 m) to another reservoir at a higher elevation (zB = 9 m) through two 25-m-long plastic pipes connected in parallel. The diameters of the two pipes are 3 cm and 5 cm. Water is to be pumped by a 68 percent efficient motor–pump unit that draws 8 kW of electric power during operation. The minor losses and the head loss in the pipes that connect the parallel pipes to the two reservoirs are considered to be negligible. Determine the total flow rate between the reservoirs and the flow rates through each of the parallel pipes.arrow_forward
- The plunger of a syringe has an internal diameter of 1.0 cm and the end of the needle has an internal diameter of 0.35 mm. A practitioner lightly squeezes the plunger, but no serum is emitted by the needle into a vein. So the practitioner gradually increases the squeezing force that she exerts on the plunger such that serum begins to be emitted from the needle into the vein. Assuming no surface tension or friction, what is the minimum squeezing force that the practitioner appli to the plunger in order that serum begins to be emitted from the needle into the vein? Take the pressure of blood in the vein to be 20 mmHg above that of atmospheric pressure. 0.70 N 1.4 N 3.3 N 1.7 N 0.21 N 0.24 Narrow_forwardDuring some actual expansion and compression processes in piston–cylinder devices, the gases have been observed to satisfy the relationship PV n = C, where n and C are constants. Calculate the work done when a gas expands from 350 kPa and 0.03 m3 to a final volume of 0.2 m3 for the case of n = 1.5.arrow_forwardGas in a container is at a pressure of 1.2 atm and a volume of 7.0 m3. (a) What is the work done on the gas if it expands at constant pressure to twice its initial volume? (b) What is the work done on the gas if it is compressed at constant pressure to one-quarter of its initial volume?arrow_forward
- College PhysicsPhysicsISBN:9781938168000Author:Paul Peter Urone, Roger HinrichsPublisher:OpenStax CollegePrinciples of Physics: A Calculus-Based TextPhysicsISBN:9781133104261Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
- Physics for Scientists and Engineers, Technology ...PhysicsISBN:9781305116399Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning