In the planetary gear system shown, the radius of gears A, B, C, and D is 3 in. and the radius of the outer gear E is 9 in. Knowing that gear A has a constant angular velocity of 150 rpm clockwise and that the outer gear E is stationary, determine the magnitude of the acceleration of the tooth of gear D that is in contact with (a) gear A, (b) gear E.
Fig. P15.118
Want to see the full answer?
Check out a sample textbook solutionChapter 15 Solutions
Vector Mechanics for Engineers: Statics and Dynamics
Additional Engineering Textbook Solutions
Thinking Like an Engineer: An Active Learning Approach (4th Edition)
Vector Mechanics for Engineers: Dynamics
Foundations of Materials Science and Engineering
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
Vector Mechanics for Engineers: Statics
Fluid Mechanics Fundamentals And Applications
- In order to uncoil electrical wire from a spool fixed to a truck, a worker drives to the left with a speed of vA = 4 m/s. At the same time, a second worker holds the cable as he walks to the right. Knowing that at the instant shown the thickness of wire on the spool is 50 mm and that the 0.6-m-radius spool has an angular velocity of 8 rad/s, determine (a) the instantaneous center of rotation of the spool, (b) the velocity of point D on the spool, (c) the speed of the second worker B.arrow_forwardThe earth makes one complete revolution on its axis in 23 h 56 min.Knowing that the mean radius of the earth is 3960 mi, determine the linear velocity and acceleration of a point on the surface of the earth (a) at the equator, (b) at Philadelphia, latitude 40° north, (c) at the North Pole.arrow_forwardIn a four bar mechanism, the dimensions of the links are as given below:AB = 50 mm, BC = 66 mmCD = 56 mm and AD = 100 mmAt a given instant when | DAB=60°the angular velocity of link AB is 10.5rad/sec in CCW direction.Determine,i) Velocity of point Cii) Velocity of point E on link BC when BE = 40 mmiii) The angular velocity of link BC and CDiv) The velocity of an offset point F on link BC, if BF = 45 mm,CF = 30 mm and BCF is read clockwise.v) The velocity of an offset point G on link CD, if CG = 24mm, DG = 44 mm and DCG is read clockwise.vi) The velocity of rubbing of pins A, B, C and D. The ratios ofthe pins are 30 mm, 40 mm, 25 mm and 35 mmrespectively.arrow_forward
- A circular plate of 120 mm radius is supported by two bearings A and B as shown. The plate rotates about the rod joining A and B with a constant angular velocity of 26 rad/s. Knowing that, at the instant considered, the velocity of Point C is directed to the right, determine the velocity and acceleration of Point E.arrow_forwardProblem 1: In a four bar mechanism, the dimensions of the links are as given below: AB = 50 mm, BC = 66 mm CD = 56 mm and AD = 100 mm At a given instant when |DAB 60o the angular velocity of link AB is 10.5 r/s in CCW direction. Determine, i) Velocity of point C ii) Velocity of point E on link BC when BE = 40 mm iii) The angular velocity of link BC and CD iv) The velocity of an offset point F on link BC, if BF = 45 mm, CF = 30 mm and BCF is read clockwise. v) The velocity of an offset point G on link CD, if CG = 24 mm, DG = 44 mm and DCG is read clockwise. vi) The velocity of rubbing of pins A, B, C and D. The ratio of the pins are 30 mm, 40 mm, 25 mm and 35 mm respectively.arrow_forwardA chain is looped around two gears of radius 40 mm that can rotate freely with respect to the 320-mm arm AB. The chain moves about arm AB in a clockwise direction at the constant rate of 80 mm/s relative to the arm. Knowing that in the position shown arm AB rotates clockwise about A at the constant rate ω = 0.75 rad/s, determine the acceleration of each of the chain links indicated Links 1 and 2.arrow_forward
- ) An overhead door is guided by wheelsn at A and B that roll in horizontal and vertical tracks. Knowing that when θ= 40° the velocity of wheel B is 0.5 m/s upward, determine (a) the angular velocity of the door, (b) the velocity of end D of the door.arrow_forwardIn a four bar mechanism, the dimensions of the links are given as AB = 50 mm, BC = 66 mm, CD = 56 mm and AD = 100 mm. At a given instant when <DAB=600 . The angular velocity of link AB is 10.5r/s in CCW direction. Determine, (i) velocity of point C, (ii) velocity of point E on link BC when BE = 40 mm, (iii) the angular velocity of link BC and CD; (iv) the velocity of an offset point F on link BC, if BF = 45 mm, CF = 30 mm and BCF is read clockwise. (v) the velocity of an offset point G on link CD, if CG = 24 mm, DG = 44 mm and DCG is read clockwise (arrow_forwardA juggling club is thrown vertically into the air. The center of gravity G of the 20-in. club is located 12 in. from the knob. Knowing that at the instant shown, G has a velocity of 4 ft/s upward and the club has an angular velocity of 30 rad/s counterclockwise, determine (a) the speeds of points A and B, (b) the location of the instantaneous center of rotation.arrow_forward
- In the planetary gear system shown, the radius of gears A, B, C, and D is 30 mm and the radius of the outer gear E is 90 mm. Knowing that gear E has an angular velocity of 180 rpm clockwise and that the central gear A has an angular velocity of 240 rpm clockwise, determine (a) the angular velocity of each planetary gear, (b) the angular velocity of the spider connecting the planetary gears.arrow_forwardThe rated speed of drum B of the belt sander shown is 2400 rpm. When the power is turned off, it is observed that the sander coasts from its rated speed to rest in 10 s. Assuming uniformly decelerated motion, determine the velocity and acceleration of point C of the belt, (a) immediately before the power is turned off, (b) 9 s later.arrow_forwardIn a four-link mechanism, the dimensions of the links are given as AB=50mm, BC=66mm, CD=56mm, and AD=100mm. At the instant when <DAB = 60° , the link AB has an angular velocity of 10.5 rad/sec in the counterclockwise direction. Both A and D lies in the horizontal plane.For the given configuration of the mechanism, determine the following: angular velocity of the link CD, angular velocity of the link BC, velocity of an offset point G on the link CD if CG=24mm,DG=44mm Instructions: configuration diagram Scale: 1:1 velocity diagram. Scale: 1m/s : 95mmarrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY