Saturated steam enters a converging–diverging nozzle at 1.75 MPa, 10 percent moisture, and negligible velocity, and it exits at 1.2 MPa. For a nozzle exit area of 25 cm2, determine the throat area, exit velocity, mass flow rate, and exit Mach number if the nozzle (a) is isentropic and (b) has an efficiency of 92 percent.
(a)
The exit velocity for isentropic converging-diverging nozzle.
The mass flow rate for isentropic converging-diverging nozzle.
The exit Mach number for isentropic converging-diverging nozzle.
The throat area for isentropic converging-diverging nozzle.
Answer to Problem 137RP
The exit velocity for isentropic converging-diverging nozzle is
The mass flow rate for isentropic converging-diverging nozzle is
The exit Mach number for isentropic converging-diverging nozzle is
The throat area for isentropic converging-diverging nozzle is
Explanation of Solution
Determine the initial specific enthalpy of the isentropic converging-diverging nozzle.
Here, the specific enthalpy of saturated liquid is
Determine the initial entropy of the isentropic converging-diverging nozzle.
Here, the specific entropy of saturated liquid is
Determine the final quality of the isentropic converging-diverging nozzle.
Here, the final entropy of the isentropic converging-diverging nozzle is
Determine the final specific enthalpy of the isentropic converging-diverging nozzle.
Determine the final specific volume of the isentropic converging-diverging nozzle.
Determine the exit velocity of the isentropic converging-diverging nozzle.
Note: the fluid flow was complete stop at the initial exit velocity then it becomes zero.
Determine the mass flow rate of the isentropic converging-diverging nozzle.
Determine the velocity of sound at the exit of the isentropic converging-diverging nozzle.
Determine the exit Mach number for isentropic converging-diverging nozzle.
Determine the critical pressure at the throat.
Here, the stagnation pressure at the initial state is
Determine the velocity of throat using steady-flow energy balance.
Note: the initial velocity is zero.
Determine the throat area for isentropic converging-diverging nozzle.
Conclusion:
At the inlet,
Perform unit conversion of pressure at state 1 from MPa to kPa.
From the Table A-5, “Saturated water-Pressure table”, obtain value of the specific enthalpy of saturated liquid, the specific enthalpy change upon vaporization, specific entropy of saturated liquid, and the specific entropy change upon vaporization at 1750 kPa of temperature as:
Substitute
Substitute
At the exit,
Perform unit conversion of pressure at state 2 from MPa to kPa.
From the Table A-5, “Saturated water-Pressure table”, obtain value of the specific volume of saturated liquid, the specific volume change upon vaporization, specific enthalpy of saturated liquid, the specific enthalpy change upon vaporization, specific entropy of saturated liquid, and the specific entropy change upon vaporization 1200 kPa of temperature as:
Substitute
Substitute
Substitute
Substitute
Thus, the exit velocity for isentropic converging-diverging nozzle is
Substitute
Thus, the mass flow rate for isentropic converging-diverging nozzle is
At state 2 entropy value for the specific volume of steam and at pressure just below and just above the specified pressure
Substitute 1.1 MPa for
Substitute
Thus, the exit Mach number for isentropic converging-diverging nozzle is
Substitute 1.75 MPa for
From the above throat pressure the value of enthalpy and specific volume as:
Substitute
Substitute
Thus, the throat area for isentropic converging-diverging nozzle is
(b)
The exit velocity for isentropic converging-diverging nozzle.
The mass flow rate for isentropic converging-diverging nozzle.
The exit Mach number for isentropic converging-diverging nozzle.
The throat area for isentropic converging-diverging nozzle.
Answer to Problem 137RP
The exit velocity for isentropic converging-diverging nozzle is
The mass flow rate for isentropic converging-diverging nozzle is
The exit Mach number for isentropic converging-diverging nozzle is
The throat area for isentropic converging-diverging nozzle is
Explanation of Solution
Determine the initial specific enthalpy of the isentropic converging-diverging nozzle.
Here, the specific enthalpy of saturated liquid is
Determine the initial entropy of the isentropic converging-diverging nozzle.
Here, the specific entropy of saturated liquid is
Determine the final quality of saturated steam for the isentropic converging-diverging nozzle.
Here, the final entropy of the isentropic converging-diverging nozzle is
Determine the final specific enthalpy of saturated steam for the isentropic converging-diverging nozzle.
Determine the enthalpy of steam at the actual exit state for the isentropic converging-diverging nozzle.
Determine the final specific enthalpy for the isentropic converging-diverging nozzle.
Determine the exit entropy of the isentropic converging-diverging nozzle.
Determine the final specific volume of the isentropic converging-diverging nozzle.
Determine the exit velocity of the isentropic converging-diverging nozzle.
Note: the fluid flow was complete stop at the initial exit velocity then it becomes zero.
Determine the mass flow rate of the isentropic converging-diverging nozzle.
Determine the velocity of sound at the exit of the isentropic converging-diverging nozzle.
Determine the exit Mach number for isentropic converging-diverging nozzle.
Determine the critical pressure at the throat.
Here, the stagnation pressure at the initial state is
Determine the actual enthalpy of steam at the throat.
Determine the velocity of throat using steady-flow energy balance.
Note: the initial velocity is zero.
Determine the throat area for isentropic converging-diverging nozzle.
Conclusion:
At the inlet,
Perform unit conversion of pressure at state 1 from MPa to kPa.
From the Table A-5, “Saturated water-Pressure table”, obtain value of the specific enthalpy of saturated liquid, the specific enthalpy change upon vaporization, specific entropy of saturated liquid, and the specific entropy change upon vaporization at 1750 kPa of temperature as:
Substitute
Substitute
At the exit,
Perform unit conversion of pressure at state 2 from MPa to kPa.
From the Table A-5, “Saturated water-Pressure table”, obtain value of the specific volume of saturated liquid, the specific volume change upon vaporization, specific enthalpy of saturated liquid, the specific enthalpy change upon vaporization, specific entropy of saturated liquid, and the specific entropy change upon vaporization 1200 kPa of temperature as:
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Thus, the exit velocity for isentropic converging-diverging nozzle is
Substitute
Thus, the mass flow rate for isentropic converging-diverging nozzle is
At state 2 entropy value for the specific volume of steam and at pressure just below and just above the specified pressure
Substitute 1.1 MPa for
Substitute
Thus, the exit Mach number for isentropic converging-diverging nozzle is
Substitute 1.75 MPa for
From the above throat pressure and entropy at the state 2ts the value of enthalpy as:
Substitute
From the above throat pressure and enthalpy at the state 2 the value of specific volume as:
Substitute
Substitute
Thus, the throat area for isentropic converging-diverging nozzle is
Want to see more full solutions like this?
Chapter 17 Solutions
Thermodynamics: An Engineering Approach
- Air flows steadily through a varying cross-sectional area duct such as a nozzle at a mass flow rate of 10 lb/s. The air enters the duct at a pressure of 200 lb/in2 and 445°F with a low velocity, and it expands in the nozzle to an exit pressure of 30 lb/in2. The duct is designed so that the flow can be approximated as isentropic. Determine the density, velocity, flow area, and Mach number at each location along the duct that corresponds to an overall pressure drop of 30 lb/in2.arrow_forwardCompressed air from the compressor of a gas turbine enters the combustion chamber at T1 = 700 K, P1 = 600 kPa, and Ma1 = 0.2 at a rate of 0.3 kg/s. Via combustion, heat is transferred to the air at a rate of 150 kJ/s as it flows through the duct with negligible friction. Determine the Mach number at the duct exit, and the drop in stagnation pressure P01 − P02 during this processarrow_forwardAir flowing at 8 psia, 480 R, and Ma1 = 2.0 is forced to undergo a compression turn of 15°. Determine the Mach number, pressure, and temperature of the air after the compression.arrow_forward
- Ahead of the normal shock wave, the upstream pressure , temperature, and Mach number are 0.53 atm, 255 K, and 2.8, respectively. Determine the pressure downstream of the shock wave.arrow_forwardCarbon dioxide flows steadily through a varying cross-sectional area duct such as a nozzle shown in fig at a mass flow rate of 3.00 kg/s. The carbon dioxide enters the duct at a pressure of 1400 kPa and 200°C with a low velocity, and it expands in the nozzle to an exit pressure of 200 kPa. The duct is designed so that the flow can be approximated as isentropic. Determine the density, velocity, flow area, and Mach number at each location along the duct that corresponds to an overall pressure drop of 200 kPa.arrow_forwardN2 enters a steady-flow heat exchanger at 150 kPa, 10°C, and 100 m/s, and it receives heat in the amount of 120 k/kg as it flows through it. The gas leaves the heat exchanger at 100 kPa with a velocity of 200 m/s. Determine the Mach number of the nitrogen at the inlet and the exit of the heat exchanger.arrow_forward
- 1- An ideal gas with k = 1.4 is flowing through a nozzle such that the Mach number is 2.4 where the flow area is 25 cm2. Assuming the flow to be isentropic, determine the flow area at the location where the Mach number is 1.2arrow_forwardFuel with heating value (HV) of 39,000 kJ/kg is burned by spraying in to 16-cm-diameter tabular combustionchamber. The air enters at 450 K, 380 kPa, and 55 m/s as shown in Figure Q3. If the exit Mach number is 0.8,determine (a) the exit temperature and,(b) the rate at which the fuel is burned.Properties of air: Specific heat capacity ratio k = 1.4, Specific heat at constant pressure c, = 1.005 kJ/kg.K,and Gas constant R = 0.287 kJ/kg.K.Use Appendix 2 for Rayleigh flow functions for an ideal gas with k = 1.4 Assume:1. Rayleigh flow (i.e., steady one-dimensional flow of an ideal gas with constant properties through aconstant cross-sectional area duct with negligible frictional effects) are valid. 2. combustion is compleso, and it is treated as a heat addition process, with no change in the chemical composition of flow 3.The increase in mass flow rate due to fuel in ection is disregardeo.arrow_forwardAn ideal gas flows through a passage that first converges and then diverges during an adiabatic, reversible, steady-flow process. For supersonic flow at the inlet, sketch the variation of pressure, velocity, and Mach number along the length of the nozzle when the Mach number at the minimum flow area is equal to unity.arrow_forward
- Nitrogen enters a converging–diverging nozzle at 800 kPa and 400 K with a negligible velocity. Determine the critical velocity, pressure, temperature, and density in the nozzle. Use data from the tables. The properties of nitrogen are k = 1.4 and R = 0.2968 kJ/kg·Karrow_forwardA gas initially at a supersonic velocity enters an adiabatic diverging duct. Discuss how this affects (a) the velocity, (b) the temperature, (c) the pressure, and (d ) the density of the fluid.arrow_forwardAn air stream with a Mach number of (3.04) a pressure of (302 kPa) and a temperature of (502 K) enters a diverging channel. If the ratio of the exit cross- sectional area to the inlet cross- sectional area is (3). Determine the back pressure which is necessary to produce a normal shock wave in the channel with a cross-sectional area equal to twice the inlet cross-sectional area. Assume steady, one-dimensional isentropic flow except through the normal shock wave. Ax=2Ai , Ae=3Aiarrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY