Introduction to Heat Transfer
6th Edition
ISBN: 9780470501962
Author: Frank P. Incropera, David P. DeWitt, Theodore L. Bergman, Adrienne S. Lavine
Publisher: Wiley, John & Sons, Incorporated
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 2, Problem 2.45P
Beginning with a differential control volume in the form of a spherical shell, derive the heat diffusion equation for a one-dimensional, spherical, radial coordinate system with internal heat generation. Compare your result with Equation 2.29.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A long wire of diameter D = 2 mm is submerged in an oil bath of temperature T∞ = 23°C. The wire has an electrical resistance per unit length of Re′=0.01 Ω/m. If a current of I = 180 A flows through the wire and the convection coefficient is h = 529 W/m2 · K, what is the steady-state temperature of the wire? From the time the current is applied, how long does it take for the wire to reach a temperature that is within 2°C of the steady-state value? The properties of the wire are ρ = 2,334 kg/m3, c = 537 J/kg · K, and k = 43 W/m · K.
Derive equations of temperature, heat flux, and heat rate for a one-dimensional, steady-state cylindraical wall with uniform generation and asymetrical surface conditions.
19) In fabrication process, steel components are formed hot and then quenched in water. Consider 2 m long, 0.2 m diameter steel cylinder (k = 40 W/m.°C, a = 10-5 m² /s), initially at 400 °C, that is suddenly quenched in water at 50 °C. If heat transfer coefficient is 200 W/m². K, calculate the following 20 min min after immersion: a) center temperature, b) surface temperature, c) The heat transferred to the water during the initial 20 min.
Chapter 2 Solutions
Introduction to Heat Transfer
Ch. 2 - Assume steady-state, one-dimensional heat...Ch. 2 - Assume steady-state, one-dimensional conduction in...Ch. 2 - A hot water pipe with outside radius r1 has a...Ch. 2 - A spherical shell with inner radius r1 and outer...Ch. 2 - Assume steady-state, one-dimensional heat...Ch. 2 - A composite rod consists of two different...Ch. 2 - A solid, truncated cone serves as a support for a...Ch. 2 - To determine the effect of the temperature...Ch. 2 - Prob. 2.9PCh. 2 - A one-dimensional plane wall of thickness 2L=100mm...
Ch. 2 - Consider steady-state conditions for...Ch. 2 - Consider a plane wall 100 mm thick and of thermal...Ch. 2 - Prob. 2.13PCh. 2 - In the two-dimensional body illustrated, the...Ch. 2 - Consider the geometry of Problem 2.14 for the case...Ch. 2 - Steady-state, one-dimensional conduction occurs in...Ch. 2 - Prob. 2.17PCh. 2 - Prob. 2.18PCh. 2 - Consider a 300mm300mm window in an aircraft. For a...Ch. 2 - Prob. 2.20PCh. 2 - Use IHT to perform the following tasks. Graph the...Ch. 2 - Calculate the thermal conductivity of air,...Ch. 2 - A method for determining the thermal conductivity...Ch. 2 - Prob. 2.24PCh. 2 - Prob. 2.25PCh. 2 - At a given instant of time, the temperature...Ch. 2 - Prob. 2.27PCh. 2 - Uniform internal heat generation at q.=5107W/m3 is...Ch. 2 - Prob. 2.29PCh. 2 - The steady-state temperature distribution in a...Ch. 2 - The temperature distribution across a wall 0.3 m...Ch. 2 - Prob. 2.32PCh. 2 - Prob. 2.33PCh. 2 - Prob. 2.34PCh. 2 - Prob. 2.35PCh. 2 - Prob. 2.36PCh. 2 - Prob. 2.37PCh. 2 - One-dimensional, steady-state conduction with no...Ch. 2 - One-dimensional, steady-state conduction with no...Ch. 2 - The steady-state temperature distribution in a...Ch. 2 - One-dimensional, steady-state conduction with no...Ch. 2 - Prob. 2.42PCh. 2 - Prob. 2.43PCh. 2 - Prob. 2.44PCh. 2 - Beginning with a differential control volume in...Ch. 2 - A steam pipe is wrapped with insulation of inner...Ch. 2 - Prob. 2.47PCh. 2 - Prob. 2.48PCh. 2 - Two-dimensional, steady-state conduction occurs in...Ch. 2 - Prob. 2.50PCh. 2 - Prob. 2.51PCh. 2 - A chemically reacting mixture is stored in a...Ch. 2 - A thin electrical heater dissipating 4000W/m2 is...Ch. 2 - The one-dimensional system of mass M with constant...Ch. 2 - Consider a one-dimensional plane wall of thickness...Ch. 2 - A large plate of thickness 2L is at a uniform...Ch. 2 - Prob. 2.57PCh. 2 - Prob. 2.58PCh. 2 - A plane wall has constant properties, no internal...Ch. 2 - A plane wall with constant properties is initially...Ch. 2 - Consider the conditions associated with Problem...Ch. 2 - Prob. 2.62PCh. 2 - A spherical particle of radius r1 experiences...Ch. 2 - Prob. 2.64PCh. 2 - A plane wall of thickness L=0.1m experiences...Ch. 2 - Prob. 2.66PCh. 2 - A composite one-dimensional plane wall is of...Ch. 2 - Prob. 2.68PCh. 2 - The steady-state temperature distribution in a...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Given a metallic block comprising of 2 unknown materials namely A and B (as shown in Figure 1 below). 1. You are tasked to determine the heat flux (W/cm2) for node at coordinate (2, 2) using finite-difference approximations using Elliptical Equation (Control Volume Approach) for the temperature gradients at this node. 2. Estimate the flux value in the horizontal direction in materials A and B, and determine if these two fluxes should be equal. 3. Calculate the vertical flux in materials A and B. Should these two fluxes be equal? The following values for the constants is as provided here: Δz = 0.5 cm, h =10 cm, ka = 0.3 W/cm · C, kb = 0.5 W/cm · C and nodal temperatures are T22 = 51.6oC, T21 = 74.2oC, T23 = 45.3oC, T32 = 38.6oC and T12 = 87.4oCarrow_forward7.Heat transfer occurs from a hot fluid, through the vessel wall, and into a cooling fluid flowing through a jacket. Neglecting the resistance of the vessel wall, derive an expression for the vessel-side heat transfer resistance divided by the total resistance to heat transfer. Neaten up your expression as much as possible,arrow_forwardA hollow aluminum sphere, with an electrical heater in the center, is used in tests to determine the thermal conductivity of insulating materials. The inner and outer radii of the sphere are o.18 and o.21 m, respectively, and testing is done under steady-state conditions with the inner surface of the aluminum maintained at 250°C. In a particular test, a spherical shell of insulation is cast on the outer surface of the sphere to a thickness of o.15 m. The system is in a room for which the air temperature is 20°C and the convection coefficient at the outer surface of the insulation is 30 W/m2. K. If 80 W is dissipated by the heater under steady-state conditions, what is the thermal conductivity of the insulation?arrow_forward
- A hot plate 1.2m wide, 0.35m high and at 1 is · Calculate the following Local heat transfer coefficient at 180 mm and average heat transfer coefficientarrow_forwardDiagram of the problem, necessary formulas, clearance and numerical solution Two heat reservoirs with respective temperatures of 325 K and 275 K are brought into contact by an iron rod 200 cm long and 24 cm2 in cross section. Calculate the heat flux between the reservoirs when the system reaches its steady state. The thermal conductivity of iron at 25 ◦C is 79.5 W/m K.arrow_forwardAs part of your work-study program at HTU, you successfully got a student job at your local ‘BEST-BURGER-IN-TOWN’ to help pay your own tuition and expenses. Since cylindrical frozen burger patties are cooked when placed on a hot stainless-steel cooking top, you like to think of the case as a conduction problem:a. Write down the appropriate general heat conduction equation that describes the cooking of those beef patties.b. Clearly state all assumptions.c. After cancelling the proper terms, write down the final energy equation for the patties.Do not solve for temperature distribution or heat transfer.arrow_forward
- A composite cylindrical wall is composed of two materials of thermal conductivity kA, andkB, which are separated by a very thin, electric resistance heater for which interfacialcontact resistances are negligible. Liquid pumped through the tube is at a temperature Too,iand provides a convection coefficient h; at the inner surface of the composite. The outersurface is exposed to ambient air, which is at Too,o and provides a convection coefficient ofho. Under steady-state conditions, a uniform heat flux of q"h is dissipated by the heater,where the reference area for this heat flux is the heater surface area. Any radiation effectscan be neglected. Sketch the equivalent thermal circuit for this system then use your circuit to develop anexpression for q''h in terms of other important variables/parameters of the system. .arrow_forwardBoth ends of a 0.6-cm copper U-shaped rod are rigidly affixed to a vertical wall as shown in the accompanying sketch. The temperature of the wall is maintained at 93C. The developed length of the rod is 0.6 m, and it is exposed to air at 38C. The combined radiation and convection heat transfer coefficient for this system is 34W/m2K. (a) Calculate the temperature of the midpoint of the rod. (b) What will the rate of heat transfer from the rod be?arrow_forward
arrow_back_ios
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Understanding Conduction and the Heat Equation; Author: The Efficient Engineer;https://www.youtube.com/watch?v=6jQsLAqrZGQ;License: Standard youtube license