Concept explainers
(a)
The work done in frictionless compression of solid cylinder of 1100-O Aluminum.
(a)
Answer to Problem 2.61P
The work done in the frictionless compression of the cylinder is
Explanation of Solution
Calculation:
The work done in frictionless compression of solid cylinder can be calculated by multiplying the specific energy and the volume of the cylinder.
For calculating the value of specific energy, the value of true strain is also required. The reduction in the height of the cylinder is 75%, thus the final height of the cylinder is 10 mm.
The value of true strain can be calculated as
The value of bulk modulus and n for the 1100-O Al are
The specific energy can be calculated as
Now, the volume of the cylinder is
Now, the work done is
Conclusion: Thus, the work done in the frictionless compression of the cylinder is
(b)
The work done in frictionless compression of solid cylinder of annealed copper.
(b)
Answer to Problem 2.61P
The work done in the frictionless compression of the cylinder is
Explanation of Solution
Calculation:
The work done in frictionless compression of solid cylinder can be calculated by multiplying the specific energy and the volume of the cylinder.
For calculating the value of specific energy, the value of true strain is also required. The reduction in the height of the cylinder is 75%, thus the final height of the cylinder is 10 mm.
The value of true strain can be calculated as
The value of bulk modulus and n for the annealed copper are
The specific energy can be calculated as
Now, the volume of the cylinder is
Now, the work done is
Conclusion: Thus, the work done in the frictionless compression of the cylinder is
(c)
The work done in frictionless compression of solid cylinder of annealed 304 stainless steels.
(c)
Answer to Problem 2.61P
The work done in the frictionless compression of the cylinder is
Explanation of Solution
Calculation:
The work done in frictionless compression of solid cylinder can be calculated by multiplying the specific energy and the volume of the cylinder.
For calculating the value of specific energy, the value of true strain is also required. The reduction in the height of the cylinder is 75%, thus the final height of the cylinder is 10 mm.
The value of true strain can be calculated as
The value of bulk modulus and n for the annealed 304 stainless steel are
The specific energy can be calculated as
Now, the volume of the cylinder is
Now, the work done is
Conclusion: Thus, the work done in the frictionless compression of the cylinder is
(d)
The work done in frictionless compression of solid cylinder of annealed 70-30 brass.
(d)
Answer to Problem 2.61P
The work done in the frictionless compression of the cylinder is
Explanation of Solution
Calculation:
The work done in frictionless compression of solid cylinder can be calculated by multiplying the specific energy and the volume of the cylinder.
For calculating the value of specific energy, the value of true strain is also required. The reduction in the height of the cylinder is 75%, thus the final height of the cylinder is 10 mm.
The value of true strain can be calculated as
The value of bulk modulus and n for the annealed 70-30 brass are
The specific energy can be calculated as
Now, the volume of the cylinder is
Now, the work done is
Conclusion: Thus, the work done in the frictionless compression of the cylinder is
Want to see more full solutions like this?
Chapter 2 Solutions
EBK MANUFACTURING PROCESSES FOR ENGINEE
- A spool of wire has a starting diameter of 2.5 mm. It is drawn through a die with an opening that is 2.1 mm at a speed of 0.3 m/s. The worked metal has a strength coefficient of 450 MPa and a strain-hardening coefficient of 0.26. Assume the drawing is performed at room temperature and that the frictional and redundant work together constitute 35% of the ideal work of deformation. Calculate the power required to carry out the operationarrow_forwardA 20 foot long x 4 feet wide x ½ inch thick sheet of an aluminum alloy is cold rolled to a thickness of ¼ inch. During the rolling operation the with of the sheet increases by 10%. The strength coefficient (K) and the strain hardening coefficient (n ) for the aluminum alloy are 25,500 psi and 0.3, respectively Calculate the true strain at the end of the rolling process.arrow_forwardA 42mm thick low carbon steel plate is reduced to 34mm in one rolling pass. At the same time that the thickness is reduced, the plate is widened by 4%. The elastic limit of the steel plate is 174MPa and its resistance is 290MPa. The input speed of the plate is 15m/min. The radius of the cylinder is 52.8mm and the rotation speed is 49 revolutions per minute. Determine: a) The minimum coefficient of friction that will make this rolling operation possible. b) The output speed of the plate c) Slide forwardarrow_forward
- What is “Necking”? How does it lead to reduction in engineering stress as true stress increases?arrow_forwardA 20 foot long x 4 feet wide x ½ inch thick sheet of an aluminum alloy is cold rolled to a thickness of ¼ inch. During the rolling operation the with of the sheet increases by 10%. The strength coefficient (K) and the strain hardening coefficient (n ) for the aluminum alloy are 25,500 psi and 0.3, respectively. Calculate the length of the sheet after the rolling operation in feet.arrow_forwardHi, can you help me solve the attached problem where I am asked to calculate the total force to obtain a component from an initial aluminum bar by using the manufacturing process of cold rolling.arrow_forward
- In a sheet metal forming press, the shape to be formed is hemispherical cup of radius 15 cm in 2mm thick mild steel sheet. The force required to deform sheet is 8 kN. The forming hammer should approach job from a distance of 30 cm. The production rate required is 240 components/hr. Calculate and suggest the following specifications of the various hydraulic components used: a. Hydraulic cylinder (bore & length); b. Pump pressure and flow rate; c. Electric motor HP considering 75% pump efficiency; d. Reservoir size; and e. Size of pump inlet and discharge tubing.arrow_forwardA metal wire of diameter 1.2 mm is used to carry a load of 1100 N. If the material of which the wire is made has a yield point of 950 MPa ultimate tensile strength of 1425 MPa then is this wire suitable for carrying that load? If yes, then support your answer with calculations and explain your results. If the answer is no, then explain why with calculations and calculate the required diameter of that wire to carry that load.arrow_forwardA plate that is 260 mm wide and 27 mm thick is to be reduced in a single pass in a two‑high rolling mill to a thickness of 22 mm. The roll has a radius = 510 mm, and its speed = 25 m/min. The work material has a strength coefficient = 235 MPa and a strain hardening exponent = 0.21. Determine (a) roll force, (b) roll torque, and (c) power required to accomplish this operationarrow_forward
- A copper strip of 200 mm width and 300 mm thickness is to be rolled to a thickness of 295 mm The roll of radius 300 mm rotates at 100 rpm. The average shear strength of the work material is 180 MPa. Calculate the roll strip contact length and the roll force .arrow_forwardA solid cylindrical slug made of 304 stainless steel is 150 mm in diameter and 100 mm high. It is reduced in height by 50% at room temperature by opendie forging with flat dies. Assuming that the coefficient of friction is 0.2 and the flow stress of this material is 1000 MPa, calculate the forging force at the end of the stroke. Manufacturing processesarrow_forwardA 300mm thick slab is being cold rolled using roll of 600mm diameter.If the coefficient of friction is 0.08. Determine the maximum possible reduction.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY