Degarmo's Materials And Processes In Manufacturing
13th Edition
ISBN: 9781119492825
Author: Black, J. Temple, Kohser, Ronald A., Author.
Publisher: Wiley,
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 23, Problem 11P
The following data apply for machining a part on a turret lathe and on an engine lathe:
One of the jobs for the engineer is to estimate the run time for a sequence of machining processes. For example:
- How many pieces would have to be made for the cost of the engine lathe to just equal the cost of the turret lathe? This is the BEQ.
- What is the cost per unit at the BEQ?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Conventional lathe and a CNC lathe are under consideration for machining a given part, data shown
2.) On a lathe, a cylindrical work piece of 100mm diameter is being turned. The RPM is 100. The lenght of the work piece is 200mm. The feed is 0.2 mm/rev. Ignoring approach and overtravel, the machining time for one pass will be nearest to (min).
For the operation of straight turning in a lathe machine, the diameter of the workpiece is 80 mm, the length is 0.12 m, the cutting speed is 80 m / min, the feed is 0.5 mm / rev and the depth of cut is 0.002 m . Find the material removing rate and the time of machining.
Chapter 23 Solutions
Degarmo's Materials And Processes In Manufacturing
Ch. 23 - How is the tool-work relationship in turning...Ch. 23 - What different kinds of surfaces can be produced...Ch. 23 - How does form turning differ from ordinary...Ch. 23 - What is the basic difference between facing and a...Ch. 23 - Which operations shown in Figure 23.3 do not form...Ch. 23 - Why is it difficult to make heavy cuts if a form...Ch. 23 - Show how equation 23.6 is an approximate equation.Ch. 23 - Why is the spindle of the lathe hollow?Ch. 23 - What function does a lathe carriage have?Ch. 23 - Why is feed specified for a boring operation...
Ch. 23 - Why are depths of cut in boring usually smaller...Ch. 23 - How can work be held and supported in a lathe?Ch. 23 - How is a workpiece that is mounted between centers...Ch. 23 - What will happen to the workpiece when turned, if...Ch. 23 - Why is it not advisable to hold hot-rolled steel...Ch. 23 - How does a steady rest differ from a follow rest?Ch. 23 - What are the advantages and disadvantages of a...Ch. 23 - Why should the distance the cutting tool overhangs...Ch. 23 - Prob. 19RQCh. 23 - How can a tapered part be turned on a lathe?Ch. 23 - Why might it be desirable to use a heavy depth of...Ch. 23 - If the rpm for a facing cut (assuming given work...Ch. 23 - Why is it usually necessary to take relatively...Ch. 23 - How does the corner radius of the tool influence...Ch. 23 - What effect does a BUE have on the diameter of the...Ch. 23 - How does the multiple-spindle screw machine differ...Ch. 23 - Why does boring ensure concentricity between the...Ch. 23 - Why are vertical spindle machines better suited...Ch. 23 - Prob. 29RQCh. 23 - Prob. 30RQCh. 23 - In which figures in this chapter is a dead center...Ch. 23 - Prob. 32RQCh. 23 - In which figures in this chapter showing setups do...Ch. 23 - How many form tools are being utilized in the...Ch. 23 - Prob. 35RQCh. 23 - Select the speed, feed, and depth of cut for...Ch. 23 - Calculate the rpm NS to run the spindle on a lathe...Ch. 23 - The lathe in problem 2 has rpm settings of 20, 30,...Ch. 23 - Calculate the cutting time if the length of cut is...Ch. 23 - Calculate the metal removal rate for machining at...Ch. 23 - Determine the speed, feed, and depth of cut when...Ch. 23 - At a speed of 90 fpm, feed of 0.030 ipr, and depth...Ch. 23 - Calculate the cutting time for a 4-in. length of...Ch. 23 - For a boring operation at V=90,fr=0.030, and...Ch. 23 - A cutting speed of 100 sfpm has been selected for...Ch. 23 - The following data apply for machining a part on a...Ch. 23 - A finish cut for a length of 10 in. on a diameter...Ch. 23 - A workpiece 10 in. in diameter is to be faced down...Ch. 23 - A hole 89 mm in diameter is to be drilled and...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
Using Fig. 4-1, draw a conclusion about the comfort of a mixed group of men and women in typical seasonal cloth...
Heating Ventilating and Air Conditioning: Analysis and Design
Determine the force in each of the cables AB and AC as a function of . If the maximum tension allowed in each c...
Engineering Mechanics: Statics
The force in members BC, CF, and FE of the truss and the state of members are in tension or compression.
Engineering Mechanics: Statics & Dynamics (14th Edition)
Determine the equations of the elastic curve using the x1 and X2 coordinates. What is the slope at A and the de...
Mechanics of Materials (10th Edition)
Determine the combined moment made by the two pairs of forces about point O and about point C. Use the values P...
Engineering Mechanics: Statics
Denver, Colorado, is called the "Mile-High City" because it is located at an elevation of approximately 5200 ft...
Applied Fluid Mechanics (7th Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Find the machining time, in seconds, and the rate of material removing in mmA3;sec for a turning operation having the following information: 1- Wp diameter is 80mm, 2- the length is 0.12m, 3- the cutting speed is 80m/min, 4- feed i50.5 mm/rev and 5- the depth of cut is 0.002m.arrow_forward1.) On a lathe, a cylindrical work piece of 100mm diameter is being turned. The RPM is 100. The cutting speed is _________?(m/min)arrow_forwardIn an orthogonal machining with a tool of gº orthogonal rake angle, the uncut chip thickness is 0.2 mm. The chip thickness fluctuates between 0.25 mm and 0 4 mm what is the ratio of the maximum shear angle to the minimum shear angle during machining?arrow_forward
- (j) In a turning operation on stainless steel with hardness = 200 HB, the cutting speed = 250 m/min, feed = 0.3 mm/rev, and depth of cut = 8 mm. How much power will the lathe draw in performing this operation if its mechanical efficiency = 95%. Use Table below to obtain the appropriate specific energy value.arrow_forward8 A job has to be machined in shaping and the process parameters are given below: a. Length of the job=120 mm b. Speed of the motor=640 rpm c. Cutting speed=264 m/min d. Tool allowance before cutting =30 mm e. Tool allowance after cutting=15mm Determine the cutting to return stroke ratio for the above operation and draw the arrangement of machining with tool head and allowances.arrow_forwardIn a turning operation, the operator has established that a single pass on the cylindrical workpiece must be completed in 5.0 min. The piece is 400 mm long and 150 mm in diameter. Using a feed of 0.30 mm / rev and a depth of cut of 4.0 mm, what speed of cut should be used to meet this machining time?arrow_forward
- Q1) Explain the four types of chips formation with sketches? What is tool life in Lathe?arrow_forwardIn a drilling operation under a given condition, the tool life found to decrease from 20 mint to 5 mint due to increase in drilling speed from 200 rpm to 400 rpm. What will be the tool life of that drill under the same condition if the drill speed is 300 rpm.arrow_forwardCalculate the machining time intervals for face milling a cutter 10 inches long, 2 inches wide, with a depth of cut of 0.1 inch for the following workpiece materials: (a) low-carbon steel ; (b) titanium alloys; (c) aluminum alloys, and (d) thermoplastics.arrow_forward
- A two-spindle drill cuts two holes at the same time, one 1/2 inch and one 3/4 inch. The workpiece is 1.0 inches thick. Both drills have point angles of 118 degrees and the cutting speed for the material is 300 ft/min. The rotational speed of each drill can be set individually but the feed rate for both holes must be set to the same value because they move together into the material. The feed rate is set so that the total metal removal rate of both drills combined does not exceed 1.50 in3/min. Determine (a) maximum feed rate (in/min) that can be used, (b) individual feeds (in/rev) for each hole, and (c) cutting time for the operation.arrow_forwardHow many parts per hour will a jig produce if the machining time is 30 seconds and it takes 2 seconds to load the part and 2 seconds to unload the part?arrow_forwardOf the following machining operations listed below, which one has the lowest cutting speed and metal removal rate and of the following machining operations listed below? Drilling Milling Turning Lappingarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Types of Manufacturing Process | Manufacturing Processes; Author: Magic Marks;https://www.youtube.com/watch?v=koULXptaBTs;License: Standard Youtube License