As in Example 27.2, consider a power supply with fixed emf ε and internal resistance r causing current in a load resistance R. In this problem, R is fixed and r is a variable. The efficiency is defined as the energy delivered to the load divided by the energy delivered by the emf. (a) When the internal resistance is adjusted for maximum power transfer, what is the efficiency? (b) What should be the internal resistance for maximum possible efficiency? (c) When the electric company sells energy to a customer, does it have a goal of high efficiency or of maximum power transfer? Explain. (d) When a student connects a loudspeaker to an amplifier, does she most want high efficiency or high power transfer? Explain.
Want to see the full answer?
Check out a sample textbook solutionChapter 27 Solutions
Physics for Scientists and Engineers with Modern Physics
Additional Science Textbook Solutions
Mathematical Methods in the Physical Sciences
MODERN PHYSICS (LOOSELEAF)
Essential University Physics: Volume 2 (3rd Edition)
Physics: Principles with Applications
Conceptual Physical Science Explorations
The Physical Universe
- In Figure, suppose the switch has been closed for a time interval sufficiently long (steady state) for the capacitor to become fully charged. R 1 = 11 kΩ, R 2 = 13 kΩ, R 3 = 3 kΩ, C = 11 × 10 −6 F, and an ideal battery has emf ε = 13 V. Find the steady state current in resistor R 1. (Your result must be in mA's and include 3 digit after the decimal point. Maximum of 5% of error is accepted in your answer.)arrow_forwardA capacitor that is initially uncharged is connected in series with a resistor and a 700.0 V emf source with negligible internal resistance. Just after the circuit is completed, the current through the resistor is 0.900 mA and the time constant for the circuit is 10.00 s. What are (a) the resistance of the resistor and (b) the capacitance of the capacitor?arrow_forwardIn (Figure 1), the battery has negligible internal resistance and EMF = 44.0 V. R1 = R2 = 3.40 Ω and R4 = 3.70 Ω. What must the resistance R3 be for the resistor network to dissipate electrical energy at a rate of 275 WW?arrow_forward
- A 3.00 M resistor and a 1.00 mF capacitor are connected in series with an ideal battery of emf e= 4.00 V.At 1.00 s after the connection is made, what is the rate at which (a) the charge of the capacitor is increasing, (b) energy is being stored in the capacitor, (c) thermal energy is appearing in the resistor, and (d) energy is being delivered by the battery?arrow_forwardIn a series RC circuit shown, the switch is closed and after a short time, the charge q on the capacitor is 5.2 x 10-5 C. What is the current in the resistor at this time?arrow_forwardIn the figure the ideal batteries have emfs 1 = 14 V and 2 = 6.0 V and the resistors have resistances R1 = 5.2 Ω and R2 = 8.9 Ω. What are (a) the current, the energy dissipation rate in (b) resistor 1 and (c) resistor 2, and the energy transfer rate in (d) battery 1 and (e) battery 2? Is energy being supplied or absorbed by (f) battery 1 and (g) battery 2?arrow_forward
- If you wish to take a picture of a bullet traveling at 500 m/s, then a very brief flash of light produced by an RC discharge through a flash tube can limit blurring. Assuming 1.00 mm of motion during one RC constant is acceptable,and given that the flash is driven by a 600-μF capacitor, what is the resistance in the flash tube?arrow_forwardAn uncharged capacitor and a resistor are connected in series to a battery as shown, where ε = 12.0 V, C = 5.00 μF, and R = 8.00 x 105 Ω. The switch is thrown to position a. Find the time constant of the circuit, the maximum charge on the capacitor, the maximum current in the circuit, and the charge and current as functions of time.arrow_forwardIn the circuit below, the capacitor starts out uncharged. The resistance is R = 118 Ω, capacitance is C = 0.0647 F, and the battery emf is 16.7 V. What is the charge (Q) on the capacitor at a time of t = 3.72 seconds after the switch is closed?arrow_forward
- As in Example 27.2, consider a power supply with fixed emf and internal resistance r causing current in a load resistance R. In this problem, R is fixed and r is a variable. The efficiency is defined as the energy delivered to the load divided by the energy delivered by the emf. (a) When the internal resistance is adjusted for maximum power transfer, what is the efficiency? (b) What should be the internal resistance for maximum possible efficiency? (c) When the electric company sells energy to a customer, does it have a goal of high efficiency or of maximum power transfer? Explain. (d) When a student connects a loudspeaker to an amplifier, does she most want high efficiency or high power transfer? Explain.arrow_forwardFigure P29.60 shows a simple RC circuit with a 2.50-F capacitor, a 3.50-M resistor, a 9.00-V emf, and a switch. What are a. the charge on the capacitor, b. the current in the resistor, c. the rate at which the capacitor is storing energy, and d. the rate at which the battery is delivering energy exactly 7.50 s alter the switch is closed?arrow_forwardIf you were to design an electric heater using Nichrome wire as the heating element, what parameters of the wire could you vary to meet a specific power output such as 1 000 W?arrow_forward
- Physics for Scientists and EngineersPhysicsISBN:9781337553278Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningPhysics for Scientists and Engineers with Modern ...PhysicsISBN:9781337553292Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningPhysics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage Learning
- Principles of Physics: A Calculus-Based TextPhysicsISBN:9781133104261Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningPhysics for Scientists and Engineers, Technology ...PhysicsISBN:9781305116399Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning