EBK AUTOMOTIVE TECHNOLOGY
6th Edition
ISBN: 9780135257470
Author: Halderman
Publisher: VST
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 28, Problem 3CQ
When removing the engine only from a vehicle equipped with an automatic transmission, the torque converter normally __________.
- a. stays mounted on the transmission
- b. is removed and stays attached to the engine
- c. must be drained
- d. remains connected to the flexplate
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
The component used to ensure that the mainshaft (output shaft) and main (speed) gear locked to it are rotating at the same speed is known as a_____.
a. synchronizer
b. shift detent
c. shift fork
d. transfer case
Technician A says the torque converter uses engine oil to provide a fluid link between engine and transmission. Technician B says the torque converter is attached to the engine crankshaft and receives the engine torque output. who is correct?
The four common configurations used as the finaldrives on FWD vehicles are the __ gear, __ gear,__ gear, and __
Chapter 28 Solutions
EBK AUTOMOTIVE TECHNOLOGY
Ch. 28 - What are the differences between a minor and a...Ch. 28 - When should the factory-installed lifting hooks be...Ch. 28 - Why should the cylinder bore be measured before...Ch. 28 - Why should the ridge that sometimes forms at the...Ch. 28 - Why should the burrs often seen at the top of the...Ch. 28 - A short block includes the __________. a. block b....Ch. 28 - Technician A says that a minor overhaul can often...Ch. 28 - When removing the engine only from a vehicle...Ch. 28 - When removing cylinder heads, the fasteners should...Ch. 28 - With the rocker cover (valve cover) removed, the...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- An engine support fixture is used to hold the engine in place while removing a ______. A. fwd transxle B. rwd transmission C. both D . neitherarrow_forwardWhich of the following is the most likely cause for a shudder during the engagement of a lock-up torque converter? a. A bad converter b. Worn or damaged CV or U-joints c. A worn front planetary gearset d. Loose flexplatearrow_forwardIn the coupling stage of conventional torque converter operation,________. a. both the impeller and turbine are turning at essentially the same speed b. both the stator and turbine are stationary c. both the stator and impeller are stationary d. the stator turns with the turbine and impellerarrow_forward
- 122) Technician A says when removing a transmission, the rear of the engine will usually need to be tilted down to allow room. Technician B says moving the position of the engine could pull electrical harnesses or coolant hoses loose. Which technician is correct? O Technician A O Technician B Both technicians A and B O Neither technician A nor Barrow_forwardin an automatic transmission or transaxle, the torque converter is used toarrow_forwardAutomatic transmissions use a __ instead of a clutchto transfer power from the flywheel to the transmission’sinput shaft.a. differentialb. U-jointc. torque converterd. constant velocity jointarrow_forward
- Which torque converter components is attached to the engine flywheel? A-impeller B-stator C-turbine D-input shaftarrow_forwardthe transfer clutch in the all-wheel-drive automatic transaxle takes the place of the _________? A.Transmission B.reduction gears C.torque converter D.interaxle differentialarrow_forward1. Torque converter it is part of brake axle clutch Automatic transmission 2. .is the source of the power in the vehicle. dund engine clutch Automatic transmission 3. The final gear reduction in the drive train occurs in the. . assembly. drive shaft rear wheel friction disc differentialarrow_forward
- 30. Which component allows the vehicle to maximize engine torque? A- Torque converter B- Differential C- Transmission D- None of thesearrow_forwardTechnician A says that all manual transmission vehicles have at least one pilot bearing or bushing for the input shaft. Technician B says that the pressure plate always rotates with the input shaft when the engine is running. ‘Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardWhich of the following components is replaced as an assembly?a. The transfer caseb. the viscous clutchc. The interaxle differentiald. all wheel drive transaxlesarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,Understanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Understanding Motor Controls
Mechanical Engineering
ISBN:9781337798686
Author:Stephen L. Herman
Publisher:Delmar Cengage Learning
Fluid Mechanics - Viscosity and Shear Strain Rate in 9 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=_0aaRDAdPTY;License: Standard youtube license