EBK AUTOMOTIVE TECHNOLOGY
6th Edition
ISBN: 9780135257470
Author: Halderman
Publisher: VST
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 28, Problem 7CQ
After the oil pan is removed, the technician should inspect __________.
- a. the oil pump and pickup screen
- b. to make certain that an rod and main bearings are numbered or marked
- c. the valve lifters (tappets) for wear
- d. Both a and b
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Which type of oil ring is slotted so that excess oil canpass through it?a. Cast ironb. Segmentedc. Both a and bd. Neither a nor b
What part of a relief valve covers the exhaust port?
A. Cap
B. Ball
C. Spring
D. Diaphragm
Which among the valves is called non return valve
a.flap check
b.ball
c.plunger valve
d.diaphragm
e.Check
Chapter 28 Solutions
EBK AUTOMOTIVE TECHNOLOGY
Ch. 28 - What are the differences between a minor and a...Ch. 28 - When should the factory-installed lifting hooks be...Ch. 28 - Why should the cylinder bore be measured before...Ch. 28 - Why should the ridge that sometimes forms at the...Ch. 28 - Why should the burrs often seen at the top of the...Ch. 28 - A short block includes the __________. a. block b....Ch. 28 - Technician A says that a minor overhaul can often...Ch. 28 - When removing the engine only from a vehicle...Ch. 28 - When removing cylinder heads, the fasteners should...Ch. 28 - With the rocker cover (valve cover) removed, the...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- d. Check oil level & moisture content 19. If the main wire (coil) to the distributor and the coil to the switch are broken, replace them and make sure the connections are clean and tight relevant to a. Breaking system b. Ignition system c. Ventilation system d. Combustion system 20. The required gap in ignition system between---------- a.-4 to 5 b.-0.4 to 5 c.-0.4 to 0.5 d.-4 to 0,5 |21. Which of the following is the fouled of spark plug a. Soot b. Oil c. Over heated d. All of the above |22.The suitable thread of spark plug for heavy engine is a. M19 b. M18 c. M15 d. M16 23. Using a Torque wrench, tighten the plugs to the specified torque. (Most) 4mm plugs are torqued to four kilograms per square inch. a. True b. False 24. Start the engine and evaluate its performance refers to a. Weekly Maintenance b. Annually Maintenance c. Daily Maintenance d. None of them 25. Check to see if Dynamo is working properly. If necessary, adjust the regulator refers to a. Weekly Maintenance b. Annually…arrow_forward__________ pump is prepared for oil production and fuel transfer a. Vane b. Screw c. Lobe d. Geararrow_forwardIn ___________ fluids coming from all sides to collide with each other at the center of the cased cylinder and dissipate the energy through “flow impingement.” a. Choke valve b. Gate valve c. Butterfly valve d. Safety valvearrow_forward
- When installing a new oil filter, it is a good idea to: Select one: a. wipe a small amount of contact cement on the gasket. b. clean all oil from the mounting area and install the gasket dry. C. wipe a small amount of oil on the new filter gasket. d. wipe a small amount of gasket sealer on the new filter gasket.arrow_forwardTechnician A says check balls are often used to block holes between the transmission valve body and the spacer plate. Technician B says spacer plates may be installed between the transmission valve body and case. Who is right?arrow_forwardThe _____ of a pressure regulator houses mechanical components a. body b. piston c. poppet d. pilotarrow_forward
- When fitting a freshly ground valve into a freshly ground seat: Technician A says that the seat should be ground more with the same stone if the margin is too small. Technician B says that the seat should be ground more with the same stone if the valve seat is too high. Who is correct?arrow_forwardChoose correct answer: A single way valve that lets air into the pneumatic system, but doesn’t allow the air to return back in same path is known as ____________ Receiver valve Three-way valve Direction control valve check valvearrow_forwardThe amount of fluid allowed to enter the cylinder can be controlled, this is done with the use of a/an ______________ control valve.arrow_forward
- Technician A says that the engine oil drain plug typically needs to be replaced with a new one at each oil change. Technician B says that engine oil drain plugs must be tightened with a torque wrench when they are installed. Who is correct? Select one: a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forwardhow are the ( Dismantling and Assembly) of plug valve ? in oil and gasarrow_forwardAn air regulator can be mounted at any position? Select: true or falsearrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningWelding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
- Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Principles of Lubrication | Automobile Engineering; Author: Magic Marks;https://www.youtube.com/watch?v=MGbbSxZTdCQ;License: Standard Youtube License