Mindtap For Erjavec/thompson's Automotive Technology: A Systems Approach, 4 Terms Printed Access Card (mindtap Course List)
7th Edition
ISBN: 9781337794381
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 39, Problem 1SA
After draining gear oil from a transaxie, the technician notices that the oil has shiny, metallic particles in it. What does this indicate?
Expert Solution & Answer
To determine
The condition it indicates if a shiny, metallic particle is draining oil from a transaxle.
Answer to Problem 1SA
It indicates the condition of excessive wear.
Explanation of Solution
Proper lubrication is required for longer transmission/transaxle life. The lubrication gear oil should be checked and replaced after required specified intervals of time. The condition of the draining oil gives a lot of indication about the parts and components of the transmission/transaxle. Thus, while draining the gear oil if it has some golden or shiny metallic particles in it, this indicates extensive internal wear or damage in the parts of a transaxle.
Want to see more full solutions like this?
Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
If the oil on the dipstick looks milky gray, it
is possible that there is water (or coolant)
being mixed into the oil. This could have
been caused by any of the following
EXCEPΤ:
Select one:
a. a bad head gasket.
b. a cracked head.
C. a leaky oil cooler.
d. a leaky fuel injector.
Technician A says that the engine oil drain
plug typically needs to be replaced with a
new one at each oil change. Technician B
says that engine oil drain plugs must be
tightened with a torque wrench when they
are installed. Who is correct?
Select one:
a. Technician A
b. Technician B
c. Both A and B
d. Neither A nor B
the speed can be positive or negative
false
true
Chapter 39 Solutions
Mindtap For Erjavec/thompson's Automotive Technology: A Systems Approach, 4 Terms Printed Access Card (mindtap Course List)
Ch. 39 - After draining gear oil from a transaxie, the...Ch. 39 - Prob. 2SACh. 39 - Prob. 3SACh. 39 - What tool is often required to remove gears and...Ch. 39 - When removing or installing bearings, where should...Ch. 39 - List five common sources for transmission fluid...Ch. 39 - What should you do to properly identify the type...Ch. 39 - List at least five items that are typically...Ch. 39 - Prob. 1TFCh. 39 - True or False? Bearing noise increases under load...
Ch. 39 - A rough, growling noise that is heard from a...Ch. 39 - A clicking noise during transrnission/transaxle...Ch. 39 - Worn teeth on a speed gear can cause_______. a....Ch. 39 - Using a lubricant that is thicker than the...Ch. 39 - A poorly adjusted shift linkage can cause which of...Ch. 39 - Technician A says that the transmission rear seal...Ch. 39 - A noise occurs in forward and reverse gears but...Ch. 39 - A rough, growling noise occurs when a vehicle with...Ch. 39 - A car jumps out of gear into neutral, particularly...Ch. 39 - While diagnosing a noise from a transmission:...Ch. 39 - Technician A says that broken or worn engine and...Ch. 39 - Technician A says that shims may be used to adjust...Ch. 39 - During a test drive, a noise that appears to be...Ch. 39 - While inspecting the synchronizers of a transaxle:...Ch. 39 - Technician A says that the proper fluid level for...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- While discussing thread sealants and lubricants: Technician A says that antiseize compound is used where a bolt might become difficult to remove after a period of time. Technician B says that thread sealants are used on bolts that are tightened into an oil cavity or coolant passage. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardDescribe the proper procedure to seal a puncture in a tire.arrow_forwardWhile discussing the results of an oil pressure test: Technician A says that when the fluid pressures are high, internal leaks, a clogged filter, low oil pump out put, or a faulty pressure regulator valve are indicated. Technician B says that if the fluid pressure increased at the wrong time, an internal leak at the servo or clutch seal is indicated. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
- True or False? Make sure you locate and adhere to the wet torque specs when tightening a bolt that has been lubricated with oil or any other liquid.arrow_forwardWhile inspecting the timing gears of an engine: Technician A says a gear with cracks, spalling, or excessive wear on the tooth surface indicates improper gear backlash. Technician B says the diameter of many of the engines timing gears and sprockets should be measured with the drive chain wrapped around the individual gears. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardAfter installing cam bearings: Technician A checks that the oi, holes in the bearings are properly aligned with those in the block by squirting oil into the holes. Technician B checks for proper alignment by inserting a wire through the holes. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- A fluid line that must be handled with special care is marked with a warning symbol. This symbol is a series of black __________________________________ on a white background. *arrow_forwardWhich of the following would NOT be cause for rejection when checking the tire condition? Any tire has a fabric break or cut exposing ply or cord or any tire is in contact with the body or frame. Any tire tread or recap is separated or any tire is flat. All of the statements shown are cause for rejection. Any tire has any bumps, bulges, or knots or is repaired with a boot or blowout patch.arrow_forwardWhat is Brake horsepower and where did the name come from?arrow_forward
- All of the following statements are correct except? a. Belts are reinforcing materials that encircle the tire under the tread. b. The carcass of a tire is made up of plies, layers of cloth, and rubber. c. Most tread patterns are designed to work well on both wet and dry roads. d. The bead is the decorative pattern at the outer edge of the tread.arrow_forwardWhat makes some spatter “hard?”arrow_forwardWhile discussing the cause of an oil leak in an axle housing, Technician A says if the fluid leaks past the threads of the drive pinion nut, the leak can be corrected by installing a copper washer under the nut. Technician B says fluid leakage past the stud nuts that hold the carrier assembly to the axle housing can be corrected by applying thread or gasket sealer on the threads and tightening the nuts to specifications. Who is correct?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Precision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Properties of Fluids: The Basics; Author: Swanson Flo;https://www.youtube.com/watch?v=TgD3nEO1iCA;License: Standard YouTube License, CC-BY
Fluid Mechanics-Lecture-1_Introduction & Basic Concepts; Author: OOkul - UPSC & SSC Exams;https://www.youtube.com/watch?v=6bZodDnmE0o;License: Standard Youtube License