Mindtap For Erjavec/thompson's Automotive Technology: A Systems Approach, 4 Terms Printed Access Card (mindtap Course List)
7th Edition
ISBN: 9781337794381
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 39, Problem 2SA
To determine
The visual inspections that should be done during inspecting the parts of transmission/transaxles.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
list five checks that should be made during the visual inspection of the parts of a transmission/transaxle.
List at least five separate checks that should be made during the visual inspection of tje transmission/transaxle
Why do we need to diagnose the transmission/transaxle failure?
Chapter 39 Solutions
Mindtap For Erjavec/thompson's Automotive Technology: A Systems Approach, 4 Terms Printed Access Card (mindtap Course List)
Ch. 39 - After draining gear oil from a transaxie, the...Ch. 39 - Prob. 2SACh. 39 - Prob. 3SACh. 39 - What tool is often required to remove gears and...Ch. 39 - When removing or installing bearings, where should...Ch. 39 - List five common sources for transmission fluid...Ch. 39 - What should you do to properly identify the type...Ch. 39 - List at least five items that are typically...Ch. 39 - Prob. 1TFCh. 39 - True or False? Bearing noise increases under load...
Ch. 39 - A rough, growling noise that is heard from a...Ch. 39 - A clicking noise during transrnission/transaxle...Ch. 39 - Worn teeth on a speed gear can cause_______. a....Ch. 39 - Using a lubricant that is thicker than the...Ch. 39 - A poorly adjusted shift linkage can cause which of...Ch. 39 - Technician A says that the transmission rear seal...Ch. 39 - A noise occurs in forward and reverse gears but...Ch. 39 - A rough, growling noise occurs when a vehicle with...Ch. 39 - A car jumps out of gear into neutral, particularly...Ch. 39 - While diagnosing a noise from a transmission:...Ch. 39 - Technician A says that broken or worn engine and...Ch. 39 - Technician A says that shims may be used to adjust...Ch. 39 - During a test drive, a noise that appears to be...Ch. 39 - While inspecting the synchronizers of a transaxle:...Ch. 39 - Technician A says that the proper fluid level for...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- 108) Technician A says that engine management malfunctions may be misinterpreted as transmission malfunction. Technician B says that imbalance in driveline components or wheels may be a likely cause of vibration. Which technician is correct? O Technician A O Technician B O Both technicians A and B O Neither technician A nor Barrow_forwardWhen servicing transfer cases, all of the following are correct, except_____. a. it must be supported on a transmission jack or safety stands b. the chain drive and a planetary gearset must be adjusted to specifications c. visual inspections for leaks and damage are necessary d. follow the manufacturers recommendations for lubricantsarrow_forwardTechnician A says that a prerequisite to accurate road-testing analysis is knowing what planetary controls are applied in a particular gear range. Technician B says that all slipping conditions can be traced to a leaking hydraulic circuit. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
- Technician A says that the proper fluid level for a manual transmission is normally to the bottom of the filler hole. Technician B says that low lubricant levels can cause a standard transmission to clash during shifting. Who is correct?arrow_forwardWhile discussing a pressure test: Technician A says that this test is the most valuable diagnostic check for slippage when a gear is engaged. Technician B says that the test can identify the cause of late or harsh shifting. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardWhich of the following is a probable cause for a converters stall speed being below specifications? a. Restricted exhaust b. Slipping transmission clutches c. Slipping transmission bands d. Worn planetary gearsetarrow_forward
- While discussing valve body assemblies in late-model transmissions: Technician A says that the valve body is no longer needed in some electronically controlled transmissions. Technician B says that an EPC solenoid maintains constant fluid pressure through the valve body regardless of the vehicle’s operating condition. Who is correct?arrow_forwardWhat is checked during a stall test?arrow_forwardExplain the benefits of dynamic testing of automatic transmission fluidarrow_forward
- True or False? Some crankshaft and camshaft timing sensors have a specified gap that must be set during installation.arrow_forwardTechnician A says that each ABS has its own diagnostic procedure involving use of the brake and antilock warning lamps, special testers, breakout boxes, scan tools, troubleshooting charts, and wiring diagrams. Technician B says that ABSs vary in the number of codes they can store and whether they will retain the code in memory when the ignition is turned off. Who is correct? Technician A only Technician B only Both A and B Neither A nor Barrow_forwardWhile discussing ways to determine if a pilot bushing is faulty: Technician A says that if it operated quietly, it does not need to be replaced. Technician B says that a careful inspection of the transmissions input shaft can determine the condition of the pilot bushing. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,